tyco PGMODIQREM Power-G Modem iQ Remote Instruction Manual

June 6, 2024
tyco

POWER-G Modem iQ Remote
High Efficient Wireless Transceiver Module

INTRODUCTION

The Power-G Modem iQ Remote low power consumption module is a wireless transceiver designed for providing simple access to wireless devices. Its main application is an RF interface in a security system that communicates Power-G messages. The transceiver features UART ports that can communicate to the host of the control panel.   mechanical support and electrical connections are obtained by mounting the modem on an 8-pin connector and fastening it with a screw to the panel mainboard.

SPECIFICATIONS

Frequency band: USA: 912-919 MHz
Bandwidth: 118 kHz Data rate: 50 Kb/s
Communication interface: UART
Antenna input: Coaxial connector U. FL-R-SMT-1(60) – Herose
Supply voltage: 3.3V +/-5%
Transmit current consumption: 35mA
Receiver current consumption: 8mA
Operating temperature: -10 + 55 °C
Dimensions: 57x25x7mm

INSTALLATION

Figure 1

Callout Description
1 Antenna connector

U. FL-R-SMT-1(60) – HEROES
2| J1 connector
3| Support screw
4| 25.0 mm
5| 57.0 mm

Function: J1 connector

  1. VCC – Operating voltage: Nominal voltage: 3.3V
  2. UART_Rx – Serial asynchronous UART receive port
  3. UART_Tx – Serial asynchronous UART transmit port
  4. GND
  5. RST – low level active
  6. SYSTEM_INT – output, low level active, BOOT0 – input, low level active
  7. Not used
  8. Not used

COMPLIANCE WITH STANDARDS

USA: FCC 47CFR Part 15
Canada: IC RSS-247
Visonic Ltd.
M/N: Power-G Modem iQ Remote
FCC ID: WP3PGMODIQREM
IC: 1467C- PGMODIQREM
OEM Integration Notices
This device is intended only for OEM integrators under the following conditions:

  1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and
  2. The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC  authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating
the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transceiver module is only authorized for use in the device when the antenna is installed and maintained at a distance of 20 cm from the user (for example wireless AP, wireless Router). The final end product must be labeled in a visible area with the following: “Contains TX FCC ID: PGMODIQREM; IC: 1467C-PGMODIQREM”.
OEM Manual Information
The OEM integrator must not provide information regarding installing or removing this RF module in the end product user manual which integrates this module. The OEM integrator user manual must include the following information in a prominent location:
“IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.”
This device complies with Part 15 of the FCC Rules and RSS-247 of ISED. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
To comply with FCC and IC RF exposure compliance requirements, the device should be located at a distance of at least 20 cm from all persons during normal operation. The antennas used for this product must not be co-located or operated in conjunction with any other antenna or transmitter.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe B est conforme a la norme NMB003 du Canada.
WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

**** W.E.E.E. Product Recycling Declaration For information regarding the recycling of this product, you must contact the company from which you originally p chased it. If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste. European Directive 2012/19/EU Waste Electrical and Electronic Equipment.

© 2021 Johnson Controls. All rights reserved. JOHNSON
CONTROLS, TYCO, and VISONIC are trademarks of Johnson Controls.
D-308486 Power-G Modem iQ Remote (Rev 0. 05/21) D-308486 POWER-G Modem iQ Remote Installation instructions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

tyco User Manuals

Related Manuals