tyco IFS04-D12-OIA4 Network Outdoor Dome Camera User Guide

tyco IFS04-D12-OIA4 Network Outdoor Dome Camera User Guide

Note: Please visit illustracameras.com for access to firmware updates that include new features, cyber-security enhancements and bug fixes.

In the box

• 1 x Flex Gen 4 Dome Camera
• 1 x Torx T10 Security L-Key
• 1 x Adaptor Plate (for use with pendant cap and electrical box)
• 3 x 18mm screws & 3 x Plastic screw anchors
• 2 x 8 mm screws (for use with the pendant cap)
• 1 x Desiccant bag
• 1 x Plastic side cover
• 1 x Waterproof cap
• 1 x Waterproof rubber insert
• 1 x Printed Regulatory Document & 1 x Printed QSG
• 1 x Mounting template sticker

Installation tools

• 1 x Screwdriver
• 1 x Drill
• 1 x Wire cutters

Figure 1: Flex Gen 4 Indoor Dome camera parts

Table 1: Flex Gen 4 Indoor Dome camera parts descriptions

Quick reference

• Default IP: 192.168.1.168 (DHCP enabled)
• Default Username / Password: admin / admin
• Power: PoE Class 3 or 24V AC / 50-60Hz / 0.6A

Table 2: Camera interior buttons and I/O ports

Figure 2: Camera interior buttons and I/O ports
Note: Use the T10 security L-Key to unscrew the three screws (5) (Figure

1. on the bubble assembly to access the interior buttons I/O ports.
   

Figure 2: Camera interior buttons and I/O ports (continued)
Note: Connectors and field wiring terminals for external Class 2 circuits provided with marking indicating minimum Class of wiring to be used. Class 2 shall be marked adjacent to the field wiring terminals.

Figure 3: Alarm and audio pin definitions

Mounting the camera

Refer to the Illustra mounting accessories webpage
https://www.illustracameras.com/products/accessories/mounts for assistance. The following mount accessory part numbers are applicable with the Illustra Flex Gen4 2MP, 4MP and 8MP Indoor Dome cameras: ADCi6DPCAPIW, IFDRECMNT, ADLOMARM, ADCDMPOLE, ADCDMCRNRO, and IBJB-F-4NSD-A.

Removing the bubble assembly from the camera base

1. Use the Torx T10 security key to unscrew the three captive screws on the bubble assembly (4) (Figure 1).
2. Lift the bubble assembly away from the camera bottom base.

Connecting the cables

The camera supports oneof the following options as a power supply.

1. AC 24V: Connect the 24V (～)cables to terminals ～AC 24V ‘OR’ Power over Ethernet (PoE): Connect the RJ-45 jack to aPoE compatible network device that supplied power through the Ethernet cable.
2. Insert the audio cable and alarm cable to the camera and connect the network cable to the RJ-45 terminal of as witch.
   Note: The power source must be NEC Class 2 or LPS. The PoE connection should be provided by a UL listed product andthe connections shall bemadein accordance with Article 800of the NEC or localregulations.

Installing the camera onto a wall or ceiling

1. Hold the guide pattern sticker up to the surface and drill three 6mm holes and
   if you are not using the cable side entry hole on the camera bottom case then cut out a cable entry hole on the surface as per the guide pattern.
   Note: If you are not using the cable side entry hole then insert the side cover.

2. Use the Torx T10 security key to unscrew the three captive screws on the bubble assembly (4) (Figure 1).

3. Use a screwdriver to remove the safety lanyard screw that is attached to the bubble assembly.
   Note: The bubble assembly is now completely disconnected from the camera bottom base.

4. Use a hammer to insert the three plastic screw anchors into the holes.

5. Remove the three captive screws on the camera bottom base (1) (Figure 4).

6. Insert the camera power cables through the cable holes on the surface or the side entry hole on the camera bottom case.

7. Hold the camera bottom case up to the wall or ceiling and connect the cables to their respective ports on the camera. See the ‘Connecting the cables section’.
   
   

8. Align the three 6mm holes on the wall or ceiling with the three holes in the camera bottom case.

9. Insert the three 18mm screws into the holes and securely attach the bottom case to the wall or ceiling.

10. Adjust the camera lens position as follows. See Figure 5.

    • Pan Adjustment (A): Rotate the lens base until you are satisfied with the field of view.

    • Tilt Adjustment (B): Tilt the eye-ball assembly as needed.

    • Rotate Adjustment (C): Rotate the 3D assembly in the camera base.
      
      Note: Limitation for the three axis positions:

    • Pan range: ±375°

    • Tilt range: 90°.

    • Rotation range (Lens): Motorized = 356°

11. Hold the bubble assembly up to the safety lanyard on the camera bottom base and align the hole on the safety lanyard with the hole on the bubble assembly.

12. Insert the safety lanyard screw into the hole and securely attach the bubble assemble to the camera bottom base.

13. Align the three holes on the bubble assembly with the three holes on the camera bottom base.

14. Use the T10 security L-Key to securely attach the three captive screws on the bubble assembly to the camera bottom base.

Installing the camera onto an electrical junction box

You can mount the camera onto a single gang or a two-gang electrical box.

1. See steps 1 and 2 in the Installing the camera onto a wall or ceiling procedure.
2. Remove the screws from the electrical box cover plate.
3. Hold the adaptor plate up to the electrical box and align the holes on the adaptor plate with the holes on the electrical box.
4. Insert the screws into the holes and securely attach the adaptor plate to the electrical box.
5. Hold the camera bottom case up to the adaptor and connect the cables to their respective ports on the camera. See the ‘Connecting the cables section’.
6. Align the three holes on the camera bottom base with the three holes on the adaptor plate.
7. Use the T10 security key to secure the three captive screws on the camera bottom base to the adaptor plate.
8. See steps 6 to 14 in the Installing the camera onto a wall or ceiling procedure to complete the installation.

Inserting the desiccant bag

1. Gently lift the tilt adjustment (C) (Figure 5).
2. Remove the desiccant from the packaging and insert the desiccant (1) (Figure 6) into the tilt adjustment.
3. Lower the tilt adjustment back into its original position.
   

Warnings

1. Installation and service should be performed only by qualified and experienced technicians and comply with all local codes and rules to maintain your warranty.
2. Theseunits operateat AC 24V/ PoE.
3. Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and wipe with a dry soft cloth.
4. Do not apply benzene or thinner to the camera, which may cause the surface of the unit to be melted or lens to be fogged.
5. Avoid operating or storing the unit in the following locations:
   • Near fluorescent lamps or objects with reflections.
   • Under unstable or flickering light sources.

Table 4: Camera part numbers and descriptions

IK10, TDN, TWDR
IFS04-D12-ITA4| Illustra Flex Gen4 4MP Mini-Dome, 2.7-13.5mm, Indoor, IP67, IK10, TDN, TWDR
IFS08-D13-ITA4| Illustra Flex Gen4 8MP Mini-Dome, 3.6-11mm, Indoor, IP67, IK10, TDN, TWDR

© 2021 Johnson Controls. All rights reserved. JOHNSON CONTROLS, TYCO and ILLUSTRA are trademarks and/or registered trademarks. Unauthorized use is strictly prohibited.

References

• Tyco Illustra Cameras | Beyond Security
• Security Camera Accessories | Home & Business | Illustra

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>