Jialexin H1 1500W Fast Heating Ceramic Electric Heater User Manual

Jialexin H1 1500W Fast Heating Ceramic Electric Heater

Thank you

Thank you for choosing our product. Please read this user manual carefully before use and keep it for future reference.

Product Diagram and Parameters

Product Parameters :

Important Security Instructions

Read and follow all safety information and instructions for future reference.

When using electrical appliances, basic precautions should always be observed to reduce the risk of fire, electric shock, and personal injury, including the following:

1. Please read all instructions before using this heater.

2. The surface of the heater will become hot during use. Avoid touching it with bare hands.

3. Do not place combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains, within at least 3 feet (0.9 m) of the front and top of the radiator. Also, please keep them away from the sides and back of the heater.

4. This equipment is not intended for use by individuals with physical, sensory, or mental impairments, or inexperienced individuals (including children) unless supervised by responsible adults.

5. Using the heater as a toy is strictly prohibited. Always supervise children when using it to prevent misuse.

6. Do not use a broken power supply cord or plug. Do not use the heater if it malfunctions or is dropped. Do not operate the heater after damage anyway. The heater should be returned to an authorized department to get fixed.

7. Do not use the heater outdoors or on wet surfaces.

8. Do not touch the plug or any part of the machine with wet hands.

9. Only use the heater in dry locations. This heater is not intended for use in bathrooms, laundry areas, and similar indoor spaces. Do not place the heater where it could fall into a bathtub or other container of water. Do not use or store it in areas where it could get wet or near a bathtub, shower, or swimming pool.

10. Do not wire under furniture or appliances. Arrange wires away from traffic areas and places where the wires will not be tripped over.

11. To shut down the heater, gently press the ON/OFF button, wait a few minutes for it to cool down, then unplug it.

12. To avoid potential fire, do not use the heater with any air-vent or exhaust opening blocked. Keep the heater away from dust, lint, hair, and any items that will reduce airflow. Do not put any objects into the air inlet/outlet as this may cause electric shock, fire, or damage to the heater.

13. There are heating, arcing, or sparking parts inside the heater. Do not use in areas where gasoline, paint, or flammable liquids are used or stored.

14. Use the heater according to the manual. Any other use may result in fires, electric shocks, personal injuries, or property damage.

15. To prevent overloads and blown fuses, make sure no other devices are plugged into the same socket or another socket connected to the same circuit

16. If the connection between the plug and the socket is loose or the plug becomes very hot, the socket may need to be replaced. Please consult a qualified electrician to replace the socket.

17. It is normal to feel hot touching the plug and power cord. The heating up and deforming may be the result of a worn socket. Worn sockets should be replaced before the further use of the heater. Plugging the heater into a worn socket may cause the power cord to overheat or catch fire.

18. The output of the heater may change, and its temperature may become high enough to burn exposed skin. This heater is not intended for people with reduced heat sensitivity or those who are unable to respond to avoid burns.

19. Make sure the heater is placed on a stable, safe surface to eliminate the possibility of tipping over.

20. Always plug the heater directly into a wall outlet. Never use an extension cord or repositionable power connector (outlet/power strip) together.

21. Make sure the plug is properly inserted into the socket. Regularly check for signs of overheating or deformation. If the socket is damaged, call your electrician.

22. Check for damage to equipment or power cords during shipping.

23. Do not attempt to modify or repair the product yourself. Doing so may void the warranty and cause damage or personal injury. Only service technicians should handle disassembly or repairs.

24. Choking Warning: Keep this remote control, which contains a small battery, out of the reach of children. Do not swallow the battery. If the battery is swallowed, seek immediate medical attention.

25. If the machine is not working properly, or if it’s been hit hard, dropped, damaged, left outdoors, or dropped in water, do not use it. Contact customer service for assistance.

26. When cleaning, storing, or not in use, turn off the heater and unplug it from the electrical outlet to allow it to cool.

Attention: During the first-time use, the heater might emit slight smoke or odor due to oil droplets on the heating coil. This is normal and will dissipate shortly.

Danger : Some abnormal conditions may cause high temperatures. Do not cover or block the front or rear part of the heater.

Operations and Functions

Product Diagrams：

1. LED Display
2. Operation Buttons
3. Pivot Joint
4. Grille
5. Base
6. Handle
7. Air Inlet
8. Dust Screen
9. Power Cord

Operation & Function:

| 1: Short press to start working with high-level heating by default. 2: Short press again to shut the heater down. 3: Long press for at least two seconds to activate the child safety lock. The child safety lock icon will light up on the LED display screen. Long press for two seconds again to unlock the child safety lock. The child safety lock icon will go out as well.
---|---
| 1: Short press to cycle through the modes: ‘High-level heat (L2) – Low-level heat (L1) – ECO mode.’ 2: Under the ECO mode, long press this button to adjust the temperature in the cycle
| 1: The heater starts with oscillation off by default. • Short press once to enable left & right oscillation. • Press again to disable left & right oscillation. • Short press again to enable up & down oscillation. • Short press again to disable up & down oscillation. 2: Long press for 2 seconds to enable both up & down and left & right oscillations simultaneously. • Long press for 2 seconds again to disable all oscillations
| 1: Short press to activate the shutdown timer, cycling through 2H-4H-6H-8H intervals. 2: Long press for 2 seconds to cancel the timer. 3: The timer would also be canceled when power is off.

Instructions:

Attention before using:

1. Check all product parts for completeness and intactness. Do not use if any damage is detected.
2. Place the product on a flat surface for proper operation. Uneven surfaces may cause the buttons on the switch to malfunction, leading to issues with the product’s functionality.
3. When using the remote control to operate the product, point it directly at the electric heater, maintain an appropriate distance, and ensure there are no barriers or obstacles between the remote control and the heater.

1. Once the power cord is plugged into the socket to supply power, the Fan Heater will beep to indicate it is powered on and in standby mode, while the LED screen light up.

2. Press the button on the top of the product’s body or on the remote control to start the heater. After hearing a ‘tick’, the heater will blow High-level hot air by default, and ‘L2’ will appear on the LED display. To activate the child safety lock, long press the on/off button for at least 2 seconds. The icon will light up on the LED display. To unlock the child safety lock, long press the button for 2 seconds again.

3. Short press the Mode button on the top of the product’s body or on the remote control, the heater turns to blow Low-level hot air instead of blowing High-level hot air, ‘L1’ Shows up on the Led display. Short press the Mode button again, the heater turns to the ECO constant temperature mode. Long press the Mode button on the top of the product’s body, the ECO icon flashes, and then short press the button again to set ECO temperature in the changing cycle of 20-35℃; The LED display shows the digits simultaneously, let go the button to confirm temperature setting. You may also set the temperature by using the buttons   and  on the remote control. After the temperature is set up, the heater turns to automatically work under the ECO constant temperature mode, the temperature of the air inlet shows up on the LED display (Indoor Temperature).

4. Short press the Oscillating button on the top of the product’s body, the heater starts oscillating Left & Right. Short press again to stop oscillating Left & Right. Short press again, the heater starts oscillating Up & Down; Short press again to stop oscillating Up & Down. Long press the Oscillating button for 2 seconds at least, Left & Right and Up & Down all start at once; Long press for 2 seconds again, Left & Right and Up & Down all go off. The buttons and on the remote control can separately turns on/off the Up & down and Left & Right oscillating. The icons and lights up on the LED display when the heater is oscillating in the corresponding mode. The lights are off when the heater stops oscillating.

5. 5.Short press the Timer button on the top of the product’s body or the buttons and on the remote control, the shutdown timer starts working. ‘0H’ Shows up on the LED display by default, the Timer icon lights on and flashes, short press again to change to ‘2H’, again to ‘4H’, again to ‘6H’, and again to ‘8H’. Repeating the cycle in such order. Long press the Timer button on the product’s body for 2 seconds at least to cancel the shutdown timer, the buttons on the remote control can only extend or shorten the timer.

6. Attention: After turning off the heater, the PTC will stop heating immediately. Please avoid cutting off power to the heater 10 seconds before it turns off in order to allow sufficient time for the PTC to cool down.

7. ECO Constant Temperature Mode: The temperature unit is °C, and the settable constant temperature range is 20 °C-35 °C (68 °F-95 °F). Due to the influence of the space heater and the environment, the displayed temperature of the space heater may be slightly different from the temperature on the thermometer.

   • Automatic Power-on Setting: For example, when the set temperature is 20 °C (68 °F), and the ambient temperature (inlet air temperature) is 19 °C (66.2 °F), the heater automatically turns on and runs at the highest level.
   • Automatic Shutdown Setting: For example, the set temperature is 20 °C (68 °F), and when the ambient temperature (inlet air temperature) reaches 22 °C (71.6 °F), the heater automatically shuts down. The space heater will then run in non-heating mode (PTC heat off) for 30 seconds and then stop.

Remote Control:

Notes：

1. When operating the heater using the remote control, ensure that the plug is inserted, the socket is powered on.
2. Use the and buttons to switch to ECO Mode. Press the button to change to Low heat state (L1) or High heat state (L2).

Other Features:

Memory Fuction

○ Once the power is on, the heater will always remember the last set modes (Temperature and Oscillation) and resume them when starting to work.

24-Hour Automatic Shutdown

○ The heater will automatically shut down after 24 hours of continuous operation without any user input.

Tip-over Protection

○ If the heater is tipped over or tripped, it will automatically stop heating, and a fault code “P4” will be displayed on its LED screen. The buzzer will also sound. To resolve this, place the heater back on a flat and stable surface, keeping it upright, and then turn it on again.

Overheat Protection

○ If the ambient temperature rises above 50°C (122°F), the heater will automatically stop heating and display a fault code “FF” on its LED screen. The buzzer will also sound as an alert. To resolve this issue, wait for the ambient temperature to drop below 50°C (122°F), then unplug the power supply and turn the heater back on.

Replacement of Remote Control Batteries

1. Remove the battery compartment cover in the direction of the indicated arrow.
2. Replace with two new button cells. Make sure the “+” and “-” poles are correctly positioned.
3. Reinstall the battery compartment cover.

Caution：

○ When replacement is required, use only new batteries of the same type.
○ Remove the batteries when the remote control will not be used for an extended period.
○ Do not attempt to remove the battery forcibly.
○ Do not dispose of the battery in fire, as it may explode or leak.

Cleaning and maintenance

It is recommended to clean the heater at least once during the operating season and before off-season storage to maintain optimum performance levels.

Before cleaning, ensure to disconnect the unit from the power supply by turning it off and unplugging it from the electrical outlet.
To clean the heater:

○ Press the on/off button on the top of the heater to turn it off. Wait for the machine to cool down, then unplug the power supply and allow the heater to cool down completely.
○ Use a soft cloth to gently wipe the outer surface of the heater. Avoid using any detergent.
○ Do not use any detergent.
○ Do not immerse the heater in water and prevent water from dripping into the motor housing. Ensure the heating element remain dry.
○ After removing the rear cover of the heater, take out the dust screen, and clean the dust with a soft brush or air gun. Make sure the dust screen is dry before putting it back into the machine if it gets wet.
○ For storage, you can cover the heater to keep dust out. Store it in a cool,
dry place, and arrange the cable away from traffic areas to prevent tripping or damage.

Warnings:

○ Do not allow water to enter the heater, as this may pose a fire or electric shock hazard.
○ For any other services or repairs, contact an authorized service representative.

Troubleshooting

The following troubleshooting guide addresses the most common problems.

returns to normal (temperature below 50°C / 122°F) before turning it back on
P4—Tip-over Protection| Place the heater back on a flat, stable surface and keep it upright
The heater does not work| The power cord is plugged in improperly| Plug to an energized socket.
Overheat protection is activated.| Turn off the heater, unplug it and wait for its cool down. Check and remove any objects on or near the heater. Wait 5-10 minutes and then reinsert the unit
No power actually passes through the unit.| Make sure your circuit breaker or fuse is working properly. Make sure your heater is placed on a flat surface.
The set temperature is lower than the room temperature.| Ensure that the thermostat is set at a temperature higher than room temperature
The heater stops Heating suddenly| Ambient temperature reaches Above 50°C / 122°F.| When the ambient temperature drops below 50°CI 122°F, unplug it from the power supply and turn it back on.
The heater is tipped over.| Place it on a flat, level and stable surface and keep it upright. Then open it again.

1 Year Warranty Against Manufacturing Defects

Products delivered to you in new condition in their original packaging are warranted against defects in materials and workmanship under normal use and service for one year, and repairs or replacements during the warranty period shall not extend the original warranty period. For products in warranty service, dated proof of purchase is required, and a copy of your dated bill of sale will satisfy this requirement.
This warranty does not cover accessories or consumables that are not warranted or replaced, such as dust screens, back covers, etc. This limited warranty covers all defects encountered during normal use of the product and does not apply to the following.

1. Loss or damage to the product due to misuse, neglect, mishandling, improper packaging, alteration, accident, current fluctuation, improper use, failure to follow safety instructions or other operating or maintenance instructions as specified in the documentation, drops, scratches and abrasions are considered to result from misuse, abuse or failure to follow the instructions in the user manual, or other documentation for the product.
2. Use of other parts or consumables that will cause damage to the product (except for those sold).
3. Privately disassembled or repaired products.
   For customer service and warranty, please contact us through our store.

eVatmaster Consulting GmbH

Bettinastr. 30 60325 Frankfurt am Main , Germany [email protected]

EVATOST CONSULTING LTD Suite 11, first floor , Moy Road Business Centre, Taffs Wall, Cardiff, Wales, CF157QR [email protected]

Manufacturer :
Manufacturer Base:
Shenzhen Carolx Technology Co., Ltd.
Floor 4, Building D, Guancheng Low Carbon Industrial
Park, Xitian Road, Guangming New District, Shenzhen

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>