HONDA E4000-01 4.0G LET User Manual
- June 6, 2024
- Honda
Table of Contents
User Manual
Product: 4.0G LET Manufacturer: Honda Motor Co., Ltd.
Model: E4000-01
For Original Equipment Manufacturer integration only this device cannot be
sold to the general public
FCC ID: N43E400001
IC: 2500A-E400001
The OEM must include the following notices as required by FCC/IC on the
product and in the User’s Manual.
This is Limited modular approval as this module is limited to installation by
the grantee into our host systems.
[for FCC]
Contains Transmitter Module FCC ID: N43E400001
or
Contains FCC ID: N43E400001
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
*If it is difficult to describe this statement on the host device due to the size, please describe it in the user’s manual and also either describe on the device packaging or on a removable label attached to the device.
[for ISED(IC)]
Contains IC : 2500A-E400001
[for FCC]
FCC CAUTION
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines. This equipment should be installed and operated keeping the
radiator at least 20cm or more away from the person’s body.
[for ISED]
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
for indoor use only
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF)
exposure rules. This equipment should be installed and operated keeping the
radiator at least 20cm or more away from the person’s body.
The following notice is not for end users but for the manufacturer of the
host device.
Therefore it isn’t described on the user manual of the host device.
This device complies with part 15 of the FCC Rules.
Part 15 Subpart C
Part 15 Subpart E
For products available in the USA/Canada market, only channels 1-11 can be
operated. Selection of other channels is not possible.
If this device is to be operated in the 5.15~5.25GHz frequency range, it is
restricted to indoor environments only.
Antenna: Proprietary
Antenna gain information: Embedded Antenna: 3.25dBi (2.4 GHz), 5.0dBi (5 GHz)
Frequency Tolerance：+/-20ppm
General Specifications
| Chipset: | QCA9377-3, (Qualcomm Atheros) |
|---|---|
| Host Interface: | Wifi: SDIO v3.0; BT: High-Speed UART |
| Operating Voltage: | 3.30 VDC +/- 5% |
| Operating Temperature: | -20 to +70 degrees C |
| Dimensions: | 18.0 x 13.0 x 2.2 mm (L x W x D) |
| Connector Type: | 52-pin proprietary |
| Radio Specifications: | 802.11b/g/n: 2.412 – 2.484 GHz; 802.11a/n: 5.18 – 5.825 |
GHz
BT: 2.402 – 2.480 GHz
Link Rates (1 stream):| IEEE 802.11b: 1-11 Mbps
IEEE 802.11g: 6-54 Mbps
IEEE 802.11a: 6-54 Mbps
IEEE 802.11n HT20: 6.5-65.0 Mbps
IEEE 802.11n HT40: 13.5-135.0 Mbps
IEEE 802.11ac VHT20: 6.5-78.0 Mbps
IEEE 802.11ac VHT40: 13.5-180.0 Mbps
IEEE 802.11ac VHT80: 29.3-390.0 Mbps
Modulation Modes:| OFDM (256QAM, 64QAM, 16QAM, QPSK, BPSK),
DSSS (CCK, DQPSK, DBPSK),
GFSK (1Mbps), π/4 DQPSK (2Mbps), 8DQPSK (3Mbps)
hardware Encryption:| WEP, WPA/WPA2 (TKIP/AES-CCMP), WAPI
Quality of Service (QoS):| WMM, WMM-PS, 802.11e
The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant (FCC Part 15.247/15.407), and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>