AUTEL Evo Lite Series Evo Lite Plus Drone User Guide

AUTEL Evo Lite Series Evo Lite Plus Drone

Reading notes

• Please read all documentation before your first flight.
• Failure to operate the aircraft responsibly could lead to injury or damages, and may void any applicable warranty coverage.

Aircraft

1. Propeller
2. Landing gear
3. Forward vision system
4. Gimbal camera
5. Front LED indicator
6. Motor
7. Power button
8. Rear vision system
9. Rear LED indicator
10. Exhaust port
11. SD card slot
12. Aircraft battery
13. USB-C port
14. Ultrasonic sensor
15. Downward vision lighting LED
16. Downward vision system

Flight LED indicator

A LED indicator is located on the end of each aircraft arm. The front LEDs will light up solid blue to help you identify the direction of the aircraft’s nose. The rear LEDs will display the current flight status of the aircraft. The chart below shows the meaning of each status indicator. The chart below shows the meaning of each status indicator.

Definitions of Flight LED Indicator Status

Front LED indicator| Rear LED indicator| Meaning
Normal status
Blue light is always

on

| Green light is always

on

| System self-test is

activated

Blue light is always

on

| Green light flashes slowly| The aircraft is in GPS

mode

Warning
Blue light is always

on

| Yellow light flashes slowly| The aircraft is in ATTI

mode

Blue light is always

on

| Yellow light flashes slowly| Low battery warning
Blue light is always

on

| Red light flashes slowly| Critical low battery warning
Blue light is always

on

| Red light flashes slowly| Critical problems, IMU error
Compass calibration
Blue light is always

on

| Yellow light is always

on

| Ready to calibrate

the compass

Blue light is always

on

| Green light is always

on

| Calibration is successful
Blue light is always

on

| Yellow light is always

on

| Calibration is failed
Pairing
Blue light flashes quickly| Green light flashes quickly| The aircraft and the remote control are being paired

Remote control

1. Power button
2. Pause button
3. Battery indicator
4. Charging interface
5. Home button
6. Joystick
7. Mobile device stand
8. Antenna
9. Remote control adapter
10. Camera/Video button
11. Custom button
12. Gimbal pitch control dial
13. Air inlet
14. Air outlet

Charge the aircraft battery & remote control

1. Aircraft battery: Press and hold the release button on both sides of battery and plug the charging cable into the charging slot of battery.
2. Charging the remote control: Insert the Type-C charging cable into the Type-C port of the remote control.

Note

• Always fully charge the aircraft and remote control batteries before flying. Please use a dedicated charger to charge the device.
• It takes about 90 minutes to fully charge the aircraft battery and 120 minutes to fully charge the remote control.
• The aircraft battery indicator will flash cyclically when it is charging, and it will be off when the battery is full.

Install the Autel SkyTM app

Refer to the following steps to connect to the application.

1. Enter the keyword “Autel Sky” in the App Store or Google Play, then search for and download the Autel SkyTM application.
2. Launch the application on your mobile device.
3. Follow the on-screen instructions to connect the mobile device and the remote control.

Prepare the aircraft

1. Please always remove the gimbal protective cover before turning on the power switch of the aircraft.
2. Unfold the arms and propellers. Important
   Before folding the arms, turn off the power switch of the aircraft. Fold the rear arm and propeller first, then fold the front arm.

Install the propellers

The propeller is installed by default on the aircraft. If you need to re- install it, please refer to the following instructions. Note that the propeller must be intact and firmly installed on the aircraft, and the propeller with the white circle mark must be paired with the motor.

• Install the propeller

1.  Confirm that the aircraft is turned off.
2. Choose the propeller that matches each motor.
3. Press down the propeller firmly, and then turn it in the locked direction to securely install the propeller.

• Disassemble the propeller

1. Turn off the aircraft.
2. Press down the propeller firmly, and then turn it in the unlocking direction to remove the propeller.![AUTEL Evo Lite Series Evo Lite Plus Drone fig11](https://manuals.plus/wp-content/uploads/2022/02/AUTEL-Evo-Lite-Series-Evo-Lite-Plus-Drone-fig11.jpg)

Introduction

Lock direction: Rotate in the indicated direction to fix the propeller.
Unlocking direction: Rotate the propeller as instructed to loosen it.
Black coded propeller>Pairing>Black coded motor
White coded propeller>Pairing>White coded motor

Warning
Before installing or removing the propeller, turn off the power switch of the aircraft.
Important
While installing or removing the propeller, it is recommended to wear protective gloves.

Prepare the remote control

1. Slowly pull out the mobile device holder.
2. When the antenna plane is facing the aircraft, the signal quality of the remote control and the aircraft can reach the best condition.

Power on

1. Hold the power button for 2 seconds to turn on the remote control.
2. Press and hold the power button for 3 seconds to turn on the aircraft. The battery indicator will then light up to show the current battery level of the aircraft.

Take off

1. Before taking off, please place the aircraft on a flat surface with the tail of the aircraft facing you.
2. Tilt the joystick inwardly or outwardly and hold for 1 second, as shown in the figure below.
3. After the motor starts, slowly push the left joystick upward (mode 2). Note: Before taking off, place the aircraft on a level surface with the back side of the aircraft facing you.

Joystick controls (Mode 2)

WWW.AUTELROBOTICS.COM
©2021-2022AUTEL ROBOTICS CO., LTD. ALL RIGHTS RESERVED

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>