AUTEL 2AGNTNEST Transmission Module User Manual

: May 15, 2024
: AUTEL

Table of Contents

Overview of Nest
Characteristics
Installation
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Nest user manual

Overview of Nest

Nest is an image transmission module with WIFI, Ethernet and RTK module designed and manufactured by Autel Robotics LTD., CO.
The module is developed based on the LTE technology platform and is suitable for point-to-point image and data bidirectional transmission. The module provides the function of automatically and manually selecting frequency bands, and has super anti-interference ability.

Characteristics

Single power supply, wide voltage input
USB+2 serial ports
Support four-frequency automatic selection, adaptive frequency point
Support wireless upgrade
Automatic network repair
Encrypted transmission
Full industrial grade components to meet the harsh working environment
Product size is small and easy to integrate Specification

Parameter	Description	Comments
System	Linux/Android
eMMC/Flash	32GB+24Gb
Image transmission Frequency	900MHz：902-928MHz

Installation

The Module use for connect to the drone and remote control, it can make the drone land precisely on the tarmac.
The module is installed in the control center area of EVO Nest, the module connects to the EVO Nest air conditioner, tarmac, charging pole, and control by the skylink app. AUTEL 2AGNTNEST Transmission Module -
Fig Below is the EVO Nest AUTEL 2AGNTNEST
Transmission Module - Fig 1

Antenna info. AUTEL 2AGNTNEST Transmission Module - Fig
2

2.4G&5GWIFI ANT
900M/2.4G/5G PCB TX&RX ANT2
900M/2.4G/5G PCB RX ANT2
900M/2.4G/5G External ANT2
900M/2.4G/5G PCB RX ANT1
900M/2.4G/5G PCB TX&RX ANT1
900M/2.4G/5G External ANT1
GNSS ANT

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modiﬁcations to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01
2.2 List of applicable FCC rules
FCC Part 15 Subpart C 15.247 & 15.407 & 15.207 & 15.209
2.3 Specific operational use conditions
The module is a Nest with WiFi 2.4GHz, WiFi 5GHz, SRD 5.2G/5.8GHz function.
The EUT has one PCB antenna, the antenna cannot be replaced by other authorized antennas, and the gain of each replacement antenna is no more than 1dBi.
This device is to be used only for mobile and fixed applications. This module can only be used with the antenna design in strict compliance with the OEM instructions provided. The odule antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required.
2.4 Limited module procedures
Not applicable. The module is a Single module and complies with the requirement of FCC Part 15.212.
2.5 Trace antenna designs
Not applicable. The module has its own antenna, and doesn’t need a host’s printed board microstrip trace antenna etc.
2.6 RF exposure considerations
The module must be installed in the host equipment such that at least 20cm is maintained between the antenna and users’ body; and if RF exposure statement or module layout is changed, then the host product manufacturer required to take responsibility of the module through a change in FCC ID or new application. The FCC ID of the module cannot be used on the final product. In these circumstances, the host manufacturer will be responsible for re- evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
2.7 Antennas
The module has its own antennas are as follows:

No.| Antenna| Antenna Type| Frequency Range| Antenna Gain
---|---|---|---|---
1| WiFi ANT| FPC Antenna| 2412MHz-2462MHz| 6.7dBi (Max.)
5180MHz-5240MHz| 4.0dBi (Max.)
5745MHz-5825MHz| 4.0dBi (Max.)
2| 900M/2.4G/5G PCB
TX&RX ANT2| PCB Antenna| 904MHz-926MHz| 3.1dBi (Max.)
2403.5MHz-2471.5MHz| 3.3dBi (Max.)
5154MHz-5246MHz| 3.0dBi (Max.)
5728MHz-5847MHz| 3.0dBi (Max.)
3| 900M/2.4G/5G PCB
RX ANT2| PCB Antenna| 904MHz-926MHz| 3.1dBi (Max.)
2403.5MHz-2471.5MHz| 3.3dBi (Max.)
5154MHz-5246MHz| 3.0dBi (Max.)
5728MHz-5847MHz| 3.0dBi (Max.)
4| 900M/2.4G/5G
External ANT2| External Antenna| 904MHz-926MHz| 5.0dBi (Max.)
2403.5MHz-2471.5MHz| 5.0dBi (Max.)
5154MHz-5246MHz| 5.0dBi (Max.)
5728MHz-5847MHz| 5.0dBi (Max.)
5| 900M/2.4G/5G PCB
RX ANT1| PCB Antenna| 904MHz-926MHz| 3.1dBi (Max.)
2403.5MHz-2471.5MHz| 3.3dBi (Max.)
5154MHz-5246MHz| 3.0dBi (Max.)
5728MHz-5847MHz| 3.0dBi (Max.)
6| 900M/2.4G/5G PCB
TX&RX ANT1| PCB Antenna| 904MHz-926MHz| 3.1dBi (Max.)
2403.5MHz-2471.5MHz| 3.3dBi (Max.)
5154MHz-5246MHz| 3.0dBi (Max.)
5728MHz-5847MHz| 3.0dBi (Max.)
7| 900M/2.4G/5G
External ANT1| External Antenna| 904MHz-926MHz| 5.0dBi (Max.)
2403.5MHz-2471.5MHz| 5.0dBi (Max.)
5154MHz-5246MHz| 5.0dBi (Max.)
5728MHz-5847MHz| 5.0dBi (Max.)

This device is intended only for host manufacturers under the following conditions:
The transmitter module may not be co-located with any other transmitter or antenna;

The module shall be only used with the original antenna(s) that has been originally tested and certified with this module. The antenna must be either permanently attached or employ ‘unique’ antenna coupler.
2.8 Label and compliance information
Host product manufacturers need to provide a physical or e-label stating “Contains FCC ID: 2AGNTNEST” with their finished product.
2.9 Information on test modes and additional testing requirements
Host manufacturer must perform test of radiated & conducted emission and spurious emission, etc. according to the actual test modes for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product.
Only when all the test results of test modes comply with FCC requirements, then the end product can be sold legally.
2.10 Additional testing, Part 15 Subpart B disclaimer
The modular transmitter is only FCC authorized for FCC Part 15 Subpart C 15.247 &15.407 & 15.207 & 15.209 and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.