Avantree Audition 3 Bluetooth Over Ear Headphones User Guide

Audition 3 Bluetooth Over Ear Headphones

Specifications

• Bluetooth version: v 5.2
• Frequency response: 20Hz-20KHz
• Bluetooth profiles: headset, handsfree, A2DP, AVRCP
• Supported audio codecs: aptX Adaptive, aptX HD, SBC, aptX
• Play time: Up to 40 hours
• Operation range: Class 2, 10 meters
• Driver size: 40mm
• Impedance: 32 ohm
• Ear pads inner diameter: 6.3cm (length)* 4cm(width) 8.5cm(width)
• Headset size: 180mm170mm80mm
• Net weight: 180g

Product Usage Instructions

Connecting the Headphones to Your Device

1. STEP 1: Turn on the headphones. They will enter pairing mode automatically on the first use. Otherwise, slide & hold to the PAIR position for about 2 seconds until you hear “Pairing” and see the LED indicator flashing red & blue.
2. STEP 2: Turn on your device’s Bluetooth and select Avantree Audition 3 in the Bluetooth menu.
3. STEP 3: Keep the headphones close to your device and wait for 5-10 seconds until they connect. Once they’re successfully connected, you’ll hear a CONNECTED voice prompt on theheadphones. The headphones’ LED indicator will become solid blue.

Charging the Headphones
OPTION 1: Place the headphones on the charging dock to charge, and make sure that the headphones’ left side is on the charging dock’s left side, otherwise, it won’t charge. The charging dock’s LED will turn red while charging and green once charging is complete.
OPTION 2: You can also charge the headphones with its power port using a charging cable. A solid red light indicates that charging is in progress; once the light turns off, your headphones will be at full battery. It typically takes 2.5 hours to fully charge.

Frequently Asked Questions (FAQ)

• Q: How do I switch between balanced and clear voice modes?
  A: Press the EQ mode button (No.4) once to switch between balanced and clear voice modes.

• Q: How can I clear the pairing history of the headphones?
  A: Press and hold both buttons for 10 seconds to clear the pairing history of the headphones.

Audition 3
Quick Start Guide

Product Introduction

Product Overview

NOTE: The base is only a charging dock, it’s not a Bluetooth transmitter.

Button Functions

1

| ****| Switch to “ON / OFF” position to turn the headphones on / off
Hold in “PAIR” position for 2 seconds to enter pairing mode

2

| ****

| Press once to increase / decrease volume
Press & hold for 2 seconds to skip / replay tracks
Press & hold both buttons for 10 seconds to clear pairing history
3| ****

| Press once to play / pause
Press once to accept / end call
Press & hold for 2 seconds to reject call
If the headphones fail to auto-connect to the last paired device, press once to reconnect
4| | Press once to switch between balanced and clear voice modes

LED Indicators

A

| Power on| Solid blue for 1 second| Welcome to Avantree
Power off| Solid red, then off| Goodbye
Pairing| Flashing red & blue| Pairing
Connected| Solid blue| Connected
Low battery| Flashing red| Low Battery (every 20 minutes)
Charging| Solid red| /
Charging complete| Solid red, then off| /
B| Charging| Solid red| /
Charging complete| Solid green| /

Connecting the Headphones to Your Device

1. STEP 1
   Turn on the headphones. They will enter pairing mode automatically on the first use. Otherwise, slide & hold to the “PAIR” position for about 2 seconds until you hear “Pairing” and see the LED indicator flashing red & blue.

2. STEP 2
   Turn on your device’s Bluetooth and select “Avantree Audition 3” in the Bluetooth menu.

3. STEP 3
   Keep the headphones close to your device and wait for 5-10 seconds until they connect. Once they’re successfully connected, you’ll hear a “CONNECTED” voice prompt on the headphones. The headphones’ LED indicator will become solid blue.

For subsequent use
Your headphones should automatically reconnect to the last-paired device within a few seconds of being turned on. If not, press once or select “Aventred Audition 3” in your device’s Bluetooth menu to reconnect.

Charging the Headphones

OPTION 1
Place the headphones on the charging dock to charge, and make sure that the headphones’ left side is on the charging dock’s left side, otherwise, it won’t charge. The charging dock’s LED will turn red while charging and green once charging is complete.

OPTION 2
You can also charge the headphones with its power port using a charging cable. A solid red light indicates that charging is in progress; once the light turns off, your headphones will be at full battery. It typically takes 2.5 hours to fully charge.

Specifications

Contact Us

avantree.com/submit-a-ticket
Support Email support@avantree.com
Support Numbers

FAQavantree.com/support/as19

Product Registration See QR code on the product.

Manufacturer:
Avantronics Limited Luohu District, Shenzhen 518000 China + 86 755 8228 5022 support@avantree.com
US Importer:
Avantree Corporation San Jose, California 95119 USA +1 800 232 2078 support@avantree.com
UK Importer:
Avantree Limited Watford, WD180 0HQ UK +44 20 8068 2023 support@avantree.com

Servicer in Europe:
Gizmex GmbH,
Sternstr. 67, 40479 Dusseldorf, Germany
+49 322 2109 7297    support@avantree.com
Model No.: BTHS-AS19
Dispose of the packaging and this product in accordance with the latest provisions.

References

• Submit a Ticket For Customer Service | Avantree
• AS19 – Avantree Support
• The Best in Audio Solutions | Avantree
• Submit a Ticket For Customer Service | Avantree

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>