SWIT BM-215NDI BM-NDI 4K Studio LCD Monitor

SWIT BM-215NDI BM-NDI 4K Studio LCD Monitor

Attention

Warning

1. Do not put the monitor in rainy or wet environment to avoid the dangerous of fire or electric shock；
2. Do not put the monitor close to any device with high-intensity magnetic.

Warning of power connection

1. Please using original power adaptor to avoid damage；
2. When using other DC power ,make sure the range of voltage,output power and polarity of it meet requirements；
3. Please cut off the power including AC power cable or battery under below conditions:
   （A）If the monitor will not be used for a long time.
   （B）If the power cable or power socket is damaged.。
   （C）If the housing of the monitor is broken by out-force or falling.

Warning of using

1. Do not touch the surface of screen directly to avoid damage,also the fingerprint on the screen will be hard to clean.
2. Do not put pressure on the LCD screen because LCD screen is fragile；
3. Do not put the monitor on anywhere unstable to avoid falling.

Maintenance and cleaning

1. Use soft dry cloth and LCD screen clean liquid to clean the dust and stain on the screen.
2. Do not put pressure on LCD screen when doing cleaning.
3. Do not clean the LCD screen by water or other chemical liquid to avoid damage.

Packing list

No.| Standard accessories

Monitor

| Quantities

X 1

---|---|---
1| Monitor| X 1
2| Battery plate（V-mount or Gold-mount）| X1
3| Monitor stand| X 2
4| Power cable| X 1

Overview

The resolution of BM-NDI series LCD monitor is up to 19201080, H178°/ V178° super wide angle of view, support 2 3G/HD/SD-SDI input , 1 HDMI 2.0 input and 1 NDI input, 1 3G/HD/SD-SDI loop out, 1 NDI to SDI loop out, 1* 3.5mm jack input and speaker.

Features

• 1920×1080 HD resolution
• Support NDI signal input, multi signal source input
• Support 16 channel embedded audio bar, any of two channel can be chosen to output
• Waveform Y/Cb/Cr/R/G/B/RGB, support single line waveform
• Support vector scope, R/G/B/Y histogram, red/blue focus assist
• Support 3DLUT（17x17x17）Auto self-calibration
• Support TSL UMD and text TALLY（TSL 3.1/4.0)
• Safety Marker：4:3/13:9/14:9/15:9/16:9/1.85:1/2.35:1/2.39:1/2:1/User 1/User 2
• Support USB firmware update and LOG file uploading (The format of USB driver should be FAT 32)
• Support Green mode.

Instruction

Front panel view

1. Tally light: Can be set to red, green and yellow
2. Speaker: Can play embedded audio of HDMI, SDI and NDI（. Speaker will not work when earphone is connecting)
3. Desktop stand feet
4. User1~User4：In order to quickly enter in the mode which was preset already .Hold the shortcut button to save current user setting.Specific please see“ The menu content-Ⅷ. System”
5. INFO：Press ”INFO” to remove or recover all current function in display like status information and A/V analyzed pattern；Press“ INFO” to exit menu when the menu is on
6. F1~F5 Function key：User can set these function key to different function according to their requirement
7. 
8. Menu/Enter：When menu is off,press the button directly to open the Main Menu；rotate “ MENU” to choose different setting selection or adjust the value；press the knob to confirm the setting；
9. LUT/Firmware：Firmware update or LUT file upload；
10. PHONE：3.5mm jack input，monitor embedded SDI and HDMI audio signal；
11. Power：power switch.

Back side view

1. SDI IN1/2： 3G-SDI

2. NDI-SDI loop out：3G-SDI

3. SDI loop out：3G-SDI

4. NDI IN：12G /3G-SDI

5. HDMI 2.0 IN：The DHCP protected content is not displayed

6. Reset: Formatting button
   Instruction（Do not do this without SWIT permission)

   • Switch off monitor；
   • Touch and keep pressing the small button with suitable tool (Do not release it when switch on monitor)
   • Switch on monitor with“ POWER” button，Tally light will show red light (release the reset button after tally light shows red light)
   • Wait for 5~10s，Tally light shows green
   • Reboot monitor to finish resetting.

7. RS485 #：TSL UMD control port

8. GPI #：GPI control port

9. Fan

10. DC IN：12V～17V

11. AC IN：100V～240V

12. Battery plate：Support V-mount battery or Gold-mount battery

OSD

1. Time code（SDI）
   Display the information of time code which is embedded in SDI signa（l LTC，VITC1&2），monitor will show“ TC:UNLOCKED” if no time code information is detected.User can set shortcut key (F1~F5) or GPI pin to“ time code” function，in order to quickly switch on/off this function.

2. On screen TALLY
   The tally signal is controlled by GPI.

3. Source ID/UMD
   Display/UMD（TSL3.1/4.0），user can set in the UMD menu.

4. Lissajous pattern
   Lissajous pattern will show audio signal，user can set shortcut key（F1~F5） or GPI pin to “Lissajous pattern” function，in order to quickly switch on/off this function.

5. Waveform
   User can switch on/off“ Waveform” function or choose different type of waveform by setting shortcut key(F1~F5) or GPI pin to“ Waveform” function on the front panel.The parameters such as on-screen-position,transparency and color of“ waveform” can be set in MENU.

6. Vector scope
   User can switch on/off“ Vector scope” function by setting shortcut key(F1~F5) or GPI pin to “Vector scope” on the front panel.The parameters such as on- screen-position, transparency and color of“ Vector scope” can be set in MENU.

7. Audio meter
   In order to monitor audio signal，User can switch on/off“ Audio meter” function by setting shortcut key(F1~F5) or GPI pin to“ Audio meter” function on the front panel. The parameters such as on-screen position, transparency and numbers of audio channel o“f Audio meter” can be set in MENU.

8. Histogram
   User can switch on/off“ Histogram” function by setting shortcut key(F1~F5) or GPI pin to “Histogram” function on the front panel.

Status

Press“ Menu/Enter”，the menu will show in the top left corner of screen，“Exit & status” will show current working status of monitor.

1. Format
   Show current input signal format；Will show“ NO SIGNAL” when there is no recognizable input signal”.Will show the format of current SDI source when the input source is SDI.

2. Channel
   Show current chosen input source.

3. Color temp
   Show current color temperature.

4. Function Key F1~F5
   Show the function of Key F1~F5.

5. Loaded Profile
   Show current user mode.

6. Network
   Show the connection status of Internet.

7. Version
   Show version of current firmware .

8. Host name
   Show the model of this monitor

Operation

Steps

1. Press“ Menu/Enter” knob，the menu will show on top left corner of screen.
2. Turn“ Menu/Enter” left and right to choose different sub-menu,the chosen one will show yellow backlight, press“Menu/Enter” knob to set the corresponding parameter.
3. Turn“ Menu/Enter” knob left and right to set corresponding parameter，press“ Menu/Enter”knob, the chosen one will show yellow backlight.
4. Turn“ Menu/Enter” knob left and right to set corresponding parameter,press“ Menu/Enter” knob to save the setting after finish adjustment.
5. Turn“ Menu/Enter” knob to choose“ EXIT”，press“ Menu/Enter” knob，exit the sub menu, choose “ EXIT & STATUS” in the main menu,press“ Menu/Enter” knob to exit main menu.

Attention

• The options which shown grey can not be set.
• The menu will save and exit automatically when no operation is performed within a period of time.

The menu content

“The menu content” will introduce the specific contents of setting in menu and sub-menu,the menu option which is noted with“ * ” will be explained in detail under the list.

Input—Set the color of input video

Menu option

Input range *1

| Instruction

Set the input range of video

| The range of value

0-1023,4-1019,64-940，64-1023

---|---|---
YUV Color Matrix| Choose YUV Color Matrix| Auto，BT.601，BT.709，BT.2020
Red Gain| Adjust the value of Red Gain| -100 ~ +100
| |
Green Gain| Adjust the value of Blue Gain| -100 ~ +100
Blue Gain| Adjust the value of Red Bias| -100 ~ +100
Red Bias| Adjust the value of Green Bias| -100 ~ +100
Green Bias| Adjust the value of Blue Bias| -100 ~ +100
Blue Bias| Reset the value of Gain and Bias| -100 ~ +100
Reset| Reset the value of Gain and Bias| /

Input range
Set the input range to compatible with input video signal,the default input range is 64-940 which is compatible with broadcast application program.

*Picture 1—Set the display of input video**

Menu option

Contrast

| Instruction

Adjust the contrast of video

| The range of value

-100 ~ +100

---|---|---
Brightness| Adjust the brightness of video| -100 ~ +100
Saturation| Adjust the saturation of video| -100 ~ +100
Sharpness| Adjust the sharpness of video| 0 ~ +100
Backlight| Adjust the backlight of video| 0 ~ +100
| |

The value of“ Contrast”“, Brightness”“, Saturation”，“Sharpness” and“ Backlight” can be quickly adjusted by the shortcut key on the front panel.

Color management—Set the color of input video

Color Gamut *1

Gamma

| Set the Color Gamut| LCD Panel，DCI-P3，Rec.709，Rec.2020
HLG System| Set the value of Gamma| 1.0，1.8，2.2，2.4，2.6，PQ1000，HLG1000，S-Log3
Tohpetisoen wilolwonulynder

tohfespveacluifiec CanodloGr aGmamat

| Gamma 2| Set HLG System Gamma| 1.0,1.1,1.2（default）,1.3,1.4,1.5
D3-Log to 709| Set the camera LUT when Color Gamut is Rec 709.| OFF，J-Log1，Log-C，S-Log2，C-Log，V-Log， RedLogFilm，S-Log3，User-Log

OFF,ARRI_Log  PQ,Cano  _CLog2Cin_PQ

D-Log to PQ| Set the camera LUT when Color Gamut is Rec.2020，Gamma is PQ1000| CREanDo_nL3_GCL1o0_gP3CQi，nS_oPnQy，_PSaLnoags3o_nCicin__VPLQog, _PQ,

SOony_SLog3o_SG3_LPGQ,Canon_CLog2Cin_HLG

FF,ARRI_L  g   _H

D-Log to HLG| Set the camera LUT when Color

HaLGm1u0t0i0s Rec.2020，Gamma is

| CREanDo_nL3_GCL1o0_gH3CLiGn，_HSLoGn，y_PSaLnoags3o_nCicin_VHLLoGg, HLG,

Sony_SLog3_SG3_HLG

Color temp| Set the value of color temperature et the value of color temperature| 2000K~10000K, D55,D65,D75,D93,USER1,USER2
Color temp(USER)| (USER)| 2000K~10000K，D55，D65，D75，D93
Red Gain| Adjust the value of Red Gain(USER)| -100 ~ +100
Green Gain| Adjust the value of Green Gain(USER)| -100 ~ +100
Blue Gain| Adjust the value of Blue Gain(USER)| -100 ~ +100
Red Bias| Adjust the value of Red Bias(USER)| -100 ~ +100
Green Bias| Adjust the value of Green Bias(USER)| -100 ~ +100
Blue Bias| Adjust the value of Blue Bias(USER)

Choose th cube file which need to

| -100 ~ +100
Import*4| be imported| None，3DLut.cube

• *1 Color Gamut
  Set the Color Gamut to match with input video.

• *2 HLG System Gamma
  Only adjustable when Gamma is HLG1000

• *3 D-Log to 709：Only adjustable when Color Gamut is Rec.709 and Gamma is between 1.0, 1.8, 2.2，2.4，2.6

• *4 Import
  Put the cube file in the root of USB driver，connect USB driver with the monitor via USB interface on the front panel,choose and import corresponding file in the menu.

Control

Ⅳ、Control

Menu option

F1*1

| Instruction| Selection
---|---|---
F2|

Set the function of shortcut key

| TimveefCoormdet,yCpoel,orinTgelme plin,Weawveafvoerfmor,m, MHiasrkoegrr,aBmlu,eOodndl/yE,AveundiForaBmare,Z,Leibssra,jVoeucstor, pattern,Focus assist,False color ,H/V delay
F3
F4
F5
*1F1~F5

*1F1~F5
Now only support“ Waveform,Vector,Audio Bar,Blue only,Marker”

Assist

Ⅴ、MAesnsuisotption

False color

| ISnwsittcrhuocnt/iooffnfalse color function| SOFeFl,eOcNtion
---|---|---
Blue only| Switch on/off Blue only function| OFF,ON
| |
Focus assist| Schwoitocsheothne/ocffoFloorcoufsita.ssist function and| OFF,Blue,Red
Zebra        Waveform| Switch on/off Zebra function| OFF,ON

WSeatvtienfgorm

| WFM Type| Switch on/off waveform function| OFF,ON
WFM Position| Set the tdyipspelaoyf Wpoasvietifonrmof Waveform pattern| Y, Cb, Cr, R,G,B, RGB
| Set the transparency of the background of| Bottom left,Bottom right,Top left,Top right
WFM Blending WFM Color| Waveform                   pattern Set the color of the Waveform| OFF,LOW,HIGH
WFM Single Line*1| Switch on/off Single line Waveform function| White,Green,Color
WFM Line Count| Adjust to show Waveform of specific lines| OFF,ON
Vector| Switch on/off Vector function| 1-2160

VSetttionrg

| CIE| Swtich on/off color gamut pattern| OFF，ON
Vector Position| Set the display position of Vector pattern.| OFF,ON
| | Bottom left,Bottom right,Top left,Top right
Vector Blending Vector color| SVect ttohreptarattnesrpna.rency of the background of

Set the color of Vector pattern

| OFF,LOW,HIGH
Histogram| Switch on/off Histogram pattern| White,Green,Color
Hseistttionggram| | | OFF,ON
Histogram Blending

Marker

| SHeistttohgeratrmanpsaptaterern c. y of the background of

Switch on/off Marker function

| OFF,LOW,HIGH

Mseattriknegr

| | | OFF,ON
Marker Select

Horizontal*2

| Set the ratio of Marker

Set the X value of Marker function

| 1.8:95，:11，5U:9S，E1R4:19，，U1S3E:9R，42:3，2.39:1，2.35:1，2:1
Vertical| Set the Y value of Marker function| 50%~99%（0~1920）
Safety area| Set the ratio of Safety area| 50%~99%（0~1080）
Fit Marker| Switch on/off Fit Marker function| 80%~99%
Center Marker| Switch on/off Center Marker function| OFF,ON
Marker Color| Set the color of Marker| OFF,ON
| Set the type of Marker| White,Red,Green,Blue,Black,Grey
Marker Type| Switch on/off Marker Outside function and| Type 1，Type 2
Marker Outside| change the color.| OFF,Black,Grey

12

• *1 WFM Single line
  Switch on“ WFM Single line” function,Monitor only show one line waveform of video. Turn “Menu/Enter” knob left and right to choose the number of waveform lines.。（The selected range of waveform lines depends on the current signal format.）

• *2 Horizontal/Vertical
  When the“ Marker Select” is“ USER 1” or“ USER 2”，User can adjust X value and Y value of Marker according to their requirement，the value is adjustable between 50%~99%（0~1920 and 0~1080）

De-embed

Menu option

Lissajous

| Instruction

Switch on/off Lissajous pattern

| Selection
---|---|---
| | OFF,ON
Lissajous Position| Set the display position of Lissajous Pattern| BToopttorimghlteft,Bottom right,Top left,
Audio Bar| Switch on/off Audio Bar function| OFF,ON left,Bottom right,Top left,

ottom

Bar Position| Set the display position of Audio Bar

Set the transparency of the background

| Top right
Bar blending| of Audio Bar .| OFF,LOW,HIGH
Bar type1| Set the type of Audio Bar| Type 1，Type 2
Left Channel| Select left input audio channel| Channel 1~16
Right Channel| Select Right input audio channel| Channel 1~16
Volume| Adjust the volume of audio signal| 0~100
H/V delay2| Switch on/off H/V delay function| ON,OFF

• *1 Bar type:Audio bar show 16 channel
  Type 1:Audio bar only
  Type 2:Show db value of audio signal，audio warning signal and right/left channel information

H/V Delay
H/V Delay is not displayed on HDMI channel.

Auto Calibration

• *1 Auto Calibration
  Monitor internally installed 3DLUT Calibrate software，support to directly connect with below calibrator via USB interface on the front panel.
  When start to calibrate, calibrate probe will read the standard color created by monitor and upload the result to monitor via USB interface.
  Monitor will compare the color which created by calibrate probe with standard color and create a 3D LUT file and finish calibrating automatically.

• *2 Probe Select
  This monitor support below kinds of calibrate prob

Start Calibration

Steps:

1. Switch on monitor.
2. Connect Calibrator with monitor via USB interface on the front pane（l Compatible with X-rite and JETI）.Make sure monitor and calibrator is in good condition and the aging time of monitor is over 30 minutes.
3. Select“ MENU”“- AUTO CALIBRATION”“- Probe Select” to select current calibrate probe.
4. Select“ Start Calibration”“- YES” to start calibrating.Monitor will show info box and calibrate position hint box，make sure the lens of calibrator is forward to the calibrate position hint box.Do not push the LCD screen when setting the calibrator.
5. Select“ OK” to do auto-calibratio.Calibrator will measure the color of screen and calibrate the screen automatically，please pay attention to the progress bar.
6. Press“ INFO” to stop calibration.When the progress bar reach to 100%，auto calibration finished. Press“ INFO”to exit menu after auto-calibration,monitor will recover to normal.
7. The screen will show the Delta value before and after calibration,shown as below

Measurement

Monitor have calibrated in factory already but also need to re-calibrate after a period of time using.Before re-calibrating“, Measurement” function will show Delta value of last time calibration, user can decide to calibrate or not from comparing the Delta value.
Connect calibrate probe with monitor and put it on the right position，Select“ Auto Calibration”“- Measurement”，Monitor will create part of color and finish testing within 30 seconds.Testing result shown as below

System

Lock, All, Rotary Knobs, Lock Key Buttons, Factory，USER1~USER4
| |
Save Profile| Save current setting to one of USER setting| USER1~USER4
Green Mode| Set the display mode of Green Mode| Black Bcklight,Grey Backlight
Idle Duration| Set the stand-by time before switch on Green Mode| 30s，1hour，2hour，4hour，OFF
DHCP3| Switch on/off DHCP Mode| ON,OFF
IP 4| Show current network information of monitor| 192.168.001.200
Net mask| 255.255.255.000

192.168.001.001

Gateway|
OSD TIME| Set the lasting time of OSD| 5~180s
Language| Select the operation language of monitor| 中文(Chinese)，English
System Reset| Reset all setting in the menu| NO/YES
Update *5| To do update for monitor| NO/YES

Key Lock

When“ Key Lock” function is“ ON”，part of menu will be hidden,only“ Menu” button is available, other button will be locked. Screen will show“ Key Locked” when the locking button is pressed,shown as below:

Recall Profile/Save Profile
Monitor supply 4 User setting,User can save current setting according to demand and habit to (USER1~USER4).After that,user only need to select“ USER1~USER4” to show corresponding menu setting.
For example: Adjust“ Color Temp” to 2200K，switch on assist function such as“ Histogram”，set function key such as F1 to“ Only Blue” ，now save all these setting to“ USER 1”，turn“ Menu/Enter” to select“ Recall Profile”“- USER 1”，monitor will change all setting to the setting which saved in“ USER 1”.

DHCP
The IP address will be assigned by router or switch automatically when“ DHCP” function is“ ON”; User can set IP/Net mask/Gateway manually to match their own Network segment when“ DHCP” function is“ OFF” in order to detect the NDI signal source in system.

IP
Connect monitor to the LAN with NDI IN/ETHERNET port in order to control monitor by website.

Website loading：Open browser and enter the IP address to load the monitor web page.

• Make sure the network cable which used to connect monitor with computer directly is cross line cable.
• Make sure the network cable which used to connect monitor with router is straight-through cable.
• If you have any problem with your network connection,please ask your network administrator for help.

Update
Firmware can be updated via USB port，update steps as below：

1. Update the latest firmware to the root of USB driver
2. Switch on monitor,connect your USB driver with monitor
3. Select“ MENU”“- SYSTEM”“- Update”,the monitor will update automatically.
4. Press“ Power” button to switch off and reboot monitor after successfully updating.

Multiview Setting

PIC 2
PIP Window Position| Set the Position of PIP on screen| Bottom left,Bottom right,Top left,Top right, Center
Border| Set the border of PIP function| ON，OFF

• *1 Multiview Type
  “ Multiview Setting” is available when signal channel is Multiview,otherwise“ Multiview setting” will show grey and unavailable. The“ Input range”“, Color gamut”“, Gamma”“, UMD” and“ Payload ID” of each video can be set separately when signal channel is“ Multiview”
  Part of menu function will be disabled when signal channel is Multiview.

• *2 PIC 1、PIC 2
  When signal channel is“ Multiview”，“PIC 1” and“ PIC 2” can select to display any signal channel

Overall Dimension

Specification

LCD Performance

Model| BM-215-NDI| BM-245-NDI
Size| 21.5| 23.8
Display area| 495.6×292.2mm| 543.0×316.72mm
Resolution| 19201080| 19201080
Display color| 16.7M| 16.7M
Display ratio| 16:9| 16:9
Brightness| 400| 400
Contrast| 3000:1| 3000:1
Viewing angle

Input /Output

| H/ V：178°/ 178°| H/ V：178°/ 178°

Input

| BNC×2| 3G/HD/SD-SDI×2
HDMI×1| HDMI Input
RS-485×2| UMD×1
GPI×1|
USB×1|
ETHERNRT/NDI| 12G/6G/3G/HD/SD
Output| BNC×1| 3G/HD/SD-SDI×1
BNC to NDI×1| 3G/HD/SD-NDI×1
RS-485×1| UMD×1
Other specification
Wvooltrakgineg| AC：100V～240V
DC/Battery：12V～17V
Power consumption| 45W
Working Temperature| 0℃～+50℃
Working Humidity| 10%～90%
Storage Temp| ﹣15℃～﹢60℃
Storage Humidity| 10%～90%
Overall Dimension

Net weight

| 530.6×364.3×74.2mm| 580.9×392.3×74.2mm
（Only monitor body）| 5.90KG| 8.87KG

Supported format: Below signal format can be displayed on the monitor

No.

|

Format

| Input terminal| Signal format shown in the Status Display as
---|---|---|---
SDI1/2| NDI| HDMI| SDI| HDMI| NDI
1| 720×480/60I| √| —| —| 720480I60| —| —
2| 720×480/60P| √| —| √| 720×480/60P| 720480P60| —
3| 720×576/50I| √| —| —| 720×576/50I| —| —
4| 720×576/50P| √| —| √| 720×576/50P| 720576I50| —
5| 1280×720/23.98P| √| —| √| 1280×720/23.98P| 1280720P24| —
6| 1280×720/24P| √| —| √| 1280×720/24P| 1280720P24| —
7| 1280×720/25P| √| —| √| 1280×720/25P| 1280720P25| —
8| 1280×720/29.97P| √| —| √| 1280×720/29.97P| 1280720P30| —
9| 1280×720/30P| √| —| √| 1280×720/30P| 1280720P30| —
10| 1280×720/50P| √| √| √| 1280720P50| 1280720P50| 1280720P50
11| 1280×720/59.94P| √| √| √| 1280720P59.94| 1280720P60| 1280720P59.94
12| 1280×720/60P| √| √| √| 1280720P60| 1280720P60| 1280720P60
13| 1920×1080/50I| √| √| √| 19201080I50| 19201080I50| 19201080I50
14| 1920×1080/59.94I| √| √| √| 19201080I59.94| 19201080I60| 19201080I60
15| 1920×1080/60I| √| √| √| 19201080I59.94| 19201080I60| 19201080I60
16| 1920×1080/23.98PSF| √| —| √| 1920×1080/23.98PSF| 19201080PSF24| —
17| 1920×1080/24PSF| √| —| √| 1920×1080/24PSF| 19201080PSF24| —
18| 1920×1080/23.98P| √| √| √| 1920×1080/23.98P| 19201080P24| 19201080P24
19| 1920×1080/24P| √| √| √| 19201080P23.98| 19201080P24| 19201080P24
20| 1920×1080/25P| √| √| √| 19201080P25| 19201080P25| 19201080P25
21| 1920×1080/29.97P| √| √| √| 19201080P29.97| 19201080P30| 19201080P30
22| 1920×1080/30P| √| √| √| 19201080P29.97| 19201080P30| 19201080P30
23| 1920×1080/48P| √| —| √| 1920×1080/48P| 19201080P48| —
24| 1920×1080/50P| √| √| √| 19201080P50| 19201080P50| 19201080P50
25| 1920×1080/59.94P| √| √| √| 19201080P59.94| 19201080P60| 19201080P59.94
26| 1920×1080/60P| √| √| √| 19201080P59.94| 19201080P60| 19201080P60
27| 2048×1080/23.98PSF| √| —| √| 2048×1080/23.98PSF| 20481080PSF24| —
28| 2048×1080/24PSF| √| —| √| 2048×1080/24PSF| 20481080PSF24| —
29| 2048×1080/25PSF| √| —| √| 2048×1080/25PSF| 20481080PSF25| —
30| 2048×1080/29.97PSF| √| —| √| 2048×1080/29.97PSF| 20481080PSF30| —
31| 2048×1080/30PSF| √| —| √| 2048×1080/30PSF| 20481080PSF30| —
32| 2048×1080/23.98P| √| —| √| 2048×1080/23.98P| 20481080P24| —
33| 2048×1080/24P| √| —| √| 2048×1080/24P| 20481080P24| —
34| 2048×1080/25P| √| —| √| 2048×1080/25P| 20481080P25| —
35| 2048×1080/29.97P| √| —| √| 2048×1080/29.97P| 20481080P30| —
36| 2048×1080/30P| √| —| √| 2048×1080/30P| 20481080P30| —
37| 2048×1080/47.94P| √| —| √| 2048×1080/47.94P| 20481080P50| —
38| 2048×1080/48P| √| —| √| 2048×1080/48P| 20481080P48| —
39| 2048×1080/50P| √| —| √| 2048×1080/50P| 2048*1080P50| —

No.

|

Format

| Input terminal| Signal format shown in the Status Display as
---|---|---|---
SDI1/2| NDI| HDMI| SDI| HDMI| NDI
40| 2048×1080/59.94P| √| —| √| 2048×1080/59.94P| 20481080P60| —
41| 2048×1080/60P| √| —| √| 2048×1080/60P| 20481080P60| —
42| 3840×2160/23.98P| —| √| √| —| 38402160P24| 38402160P23.98
43| 3840×2160/24P| —| √| √| —| 38402160P24| 38402160P24
44| 3840×2160/25P| —| √| √| —| 38402160p25| 38402160p25
45| 3840×2160/29.97P| —| √| √| —| 38402160P30| 38402160P29.97
46| 3840×2160/30P| —| √| √| —| 38402160P30| 38402160P30
47| 3840×2160/47.94P| —| —| √| —| 38402160P50| —
48| 3840×2160/48P| —| —| √| —| 38402160P48| —
49| 3840×2160/50P| —| —| √| —| 38402160P50| —
50| 3840×2160/59.94P| —| —| √| —| 38402160P60| —
51| 3840×2160/60P| —| —| √| —| 38402160P60| —
52| 4096×2160/23.98P| —| —| √| —| 40962160P24| —
53| 4096×2160/24P| —| —| √| —| 40962160P24| —
54| 4096×2160/25P| —| —| √| —| 40962160P25| —
55| 4096×2160/29.97P| —| —| √| —| 40962160P30| —
56| 4096×2160/30P| —| —| √| —| 40962160P30| —
57| 4096×2160/47.94P| —| —| √| —| 40962160P48| —
58| 4096×2160/48P| —| —| √| —| 40962160P48| —
59| 4096×2160/50P| —| —| √| —| 40962160P50| —
60| 4096×2160/59.94P| —| —| √| —| 40962160P60| —
61| 4096×2160/60P| —| —| √| —| 4096*2160P60| —

Troubleshooting

Problem| Possible fault reasons| Solution

Check the power connection of monitor,press“POWER”

---|---|---

No video

| Monitor have not switched on Wrong input source is selected.| button on the front panel.
| Press“Source”button to change the input source
No NDI signal source is selected| Select NDI signal in“NDI source”
Input voltage is not stable| Reconnect the power
Scoignnnaelcctaiobnle loose/wrong| Ccohnenckecstiigonnailscraigbhlet,make sure the signal cable
Tphoewberatwtehreynppoowweerriesdoubtyobfattery| Change a new battery
The polarity is reversed when using DIY power supply| Reconnect the cable refer to standard power supply.
The Network segment of monitor and NDI source is not same.| 12. MSwakitechsuorne“thDeHsCePg”mfuenct toiof nmtoonaitsosriganntdhNe DIPI saodudrrceessis same；

automatically

Image    or color abnormal

| Signal cable is in poor contact| Change a new signal cable
Video signal interference| Remove interference sources
Parameters of color is over adjust| Upload User mode to“Factory”
Video is distorted| Reset the aspect ratio
Video show all blue| Switch off“Blue only”function
The“focus assist”function is“ON”| Switch off“Focus assist”function
The“False Color”function is“ON”| Switch off“False Color”function
No audio output| Monitor is set to mute mode| Turn“MENU/ENTER”knob left and right to adjust volume
Audio cable is in poor contact| Change audio cable
Audio cable is disconnected or connect wrong.| Check and reconnect the audio cable

Company Statement

Any internal technology (including hardware equipment, software design and product trademark) of the product shall be protected by law, and any infringement of intellectual property rights of the product shall be investigated for legal liability.
All the brand and trademark in this product are protected by law,all other company’s brand and trademark in this product are protected by their owner’s law.
In order to better service majority users, SWIT products will keep improving and developing, SWIT keep the right to revise and improve this user manual without previous notice.
The warranty period of this product are two years,the following condition are not covered by the warranty:

1. The appearance and the LCD panel are damaged by man-made out force；
2. The amount of defective pixels are under three；
3. The product is damaged by using incompatible power adaptor；
4. The product is damaged by failure to use, maintain or storage according to the user manual.；
5. The product is disassembled by user in the process of using；
6. ther faults or damages not caused by design ,technology,manufacture and quality.
   ＊Any sales person have no right to provide extra warranty beyond these terms.

Please feel free to contact with us by phone, fax or email when you have any question or need any help in the process of using.

• This user manual applies to all BM-NDI model monitor, all the illustration take BM-215-NDI for example, any difference of specification or appearance, this manual will be attached text explanation;
• The function with mark ”#” in this user manual have not been realized yet.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>