ROTENSO SETU Remote Control User Manual

: June 6, 2024
: ROTENSO

CONTROL
SERIES
REMOTE CONTOL
USER MANUAL
MODELE: SETU

www.rotenso.com

PRECAUTIONS

WARNING

Only qualified personnel should install and service the equipment. The installation, starting up and servicing of heating, ventilating, and air- conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person could result in death or serious injury. When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that are attached to the equipment.

Read the following if you use the device in European countries:
The device can not be operated by children over 7 years old, disabled people, and oraz people without experience and knowledge. Instructions should include a description of the correct and safe handling of the device and oraz information about possible dangers. Children should not play with the device. Cleaning and servicing should be carried out by authorized persons.

UTILIZATION:
Do not dispose of this product together with unsorted municipal waste.
It’s necessary to transfer this type of waste for special processing.
It’s illegal to throw the device together with other household waste.
There are several ways to get rid of this type of equipment:w
A. The city organizes electronic waste collection, you can pass the device without the cost.
B. When you buy a new device the seller will accept the old device without any fees.
C. Manufacturer will take the product from buyer product without charging it with costs.
D. Products of this type contains valuable elements, it can be sold sprzedane on purchase of metals.
Throwing the device, on wild” exposes you to the risk of losing your health. Dangerous substances from the device can penetrate to groundwater creating a danger of getting through to people’s food chain.

REMOTE CONTROL SUPPORT

TECHNICAL SPECIFICATIONS

Model	SETU
Power	3.0V ( Dry batteries R03/LR03×2)
Remote range	8m
Working temperature	-5°C~60°C(23°F~140°F)

QUICKSTART GUIDE

NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a detailed description of how to use your air conditioner.

SPECIAL NOTE

Button designs on your unit may differ slightly from the example shown.
If the indoor unit does not have a particular function, pressing that function’s button on the remote control will have no effect.
When there are wide differences between “Remote controller Manual” and “USER’S MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.

HANDLING THE REMOTE CONTROLLER

Inserting and Replacing Batteries

Your air conditioning unit may come with two batteries(some units). Put the batteries in the remote control before use.
3. Slide the back cover from the remote control downward, exposing the battery compartment.
4. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
5. Slide the battery cover back into place.

WARNING

For optimum product performance:

Do not mix old and new batteries or batteries of different types.
Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.
Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

TIPS for Using the remote control

The remote control must be used within 8 meters of the unit.
The unit will beep when a remote signal is received.
Curtains, other materials, and direct sunlight can interfere with the infrared signal receiver.
Remove batteries if the remote will not be used for more than 2 months.

Notes for using the remote control

The device could comply with the local national regulations.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment.

BUTTONS AND FUNCTIONS

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control.
The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual.

ON/OFF
Button to turn on and turn off the air conditioner.
TEMP ∧
Increases temperate in 1°C (1°F) increments. Max. temperature is 30°C (86°F).
Note: Press together ∧ & ∨ buttons at the same time for 3 seconds will alternate the temperature display between the °C & °F.
SET
Scrolls through operation functions as follows:
Breeze Away ( ) →Sleep ( )→ Follow Me ( ) →AP mode ( ) Sleep ( ) →Funkcja Breeze Away ( ) →… The selected symbol will flash on the display area, press the OK button to confirm.
TEMP ∨
Decreases temperature in 1°C (1°F) increments. Min. temperature is 16°C (60°F).
FAN SPEED
Selects fan speeds in the following order: AU 20% 40% 60% 80% 100%. Press together & buttons to increase/decrease the fan speed in 1% increments.
SWING
Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate the vertical louver auto swing feature.
MODE
Scrolls through operation modes as follows: AUTO →COOL →DRY →HEAT→ FAN
Note: HEAT mode is not supported by the cooling-only appliance.
ECO/GEAR
Press this button to enter the energy-efficient mode in a sequence of the following: ECO →GEAR (75%) →GEAR (50%)→ Previous setting mode→ …
OK
Used to confirm the selected functions.
TIMER
Set timer to turn unit on or off
FRESH
Used to starts and stop the Fresh feature.
CLEAN Used to start/stop the Self Clean or Active Clean function. (Model dependent, please refer to the USER’S OPERATION & INSTALLATION MANUAL).
LED
Turns the indoor unit’s LED display and air conditioner buzzer on and off (model dependent), which creates a comfortable and quiet environment.
Turbo
Enables the unit to reach present temperature in the shortest possible time.

REMOTE SCREEN INDICATORS

Information is displayed when the remote controller is powered up.

NOTE

All indicators shown in the figure are for the purpose of clear presentation. But during the actual operation, only the relative function signs are shown on the display window.

| Breeze Away display (some units)
Active clean feature display
Fresh feature display
Sleep mode display
Follow me feature display
Wireless control feature display
Low battery detection display (If flashes)
---|---

| Auto mode
Cool mode
Dry mode| | Heat mode
Fan mode
---|---|---|---

| ECO display
Displays when ECO feature is activated
GEAR display
Displays when GEAR feature is activated
LOCK display
Displays when LOCK feature is activated.
---|---

| Horizontal louver swing display

Vertical louver auto swing display
TURBO mode display
Not available for this unit
Not available for this unit
---|---

|

Fan speed display

1%
2%-20%
21%-40%
41%-60%
61%-80%
81%-100% *

---|---

This fan speed can not be adjusted in AUTO or DRY mode.
Note: [*] Not all the models can display the fan speed values between AU-100%.

6. Temperature/Timer/Fan speed

Displays the set temperature by default, or fan speed or timer setting when using TIMER ON/OFF functions.
Temperature range:
16-30°C/60-86°F/(20-28°C/68-82°F) (Model dependent)
Timer setting range: 0-24 hours
Fan speed setting range: AU -100%
This display is blank when operating in FAN mode.

| Transmission Indicator
Lights up when remote sends a signal to indoor unit
TIMER ON display
TIMER OFF display
Silence feature display
---|---

HOW TO USE BASIC FUNCTIONS

Information is displayed when the remote controller is powered up.

ATTENTION
Before the operation, please ensure the unit is plugged in and power is available.

AUTO mode

NOTE:

In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT function based on the set temperature.
In AUTO mode, fan speed can not be set.

COOL or HEAT mode

DRY Mode

NOTE:
In DRY mode, fan speed can not be set since it has already been automatically controlled.

FAN Mode

NOTE:
In FAN mode, you can’t set the temperature. As a result, no temperature is displayed in the remote screen.

Setting the TIMER

TIMER ON/OFF – Set the amount of time after which the unit will automatically turn on/off.

TIMER ON setting

Press TIMER button to initiate the ON time sequence.

Press Temp. up or down button multiple times to set the desired time to turn on the unit.

Point remote to unit and wait 1sec, the TIMER ON will be activated.

TIMER OFF setting

Press the TIMER button to initiate the OFF time sequence.

Press Temp. up or down button multiple times to set the desired time to turn off the unit

Point remote to the unit and wait 1sec, the TIMER OFF will be activated.

NOTE:

When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1-hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24.
Cancel either function by setting its timer to 0.0h.

TIMER ON & OFF setting (example)
Keep in mind that the time periods you set for both functions refer to hours after the current time.

Example: If the current timer is 1:00 PM, to set the timer as above steps, the unit will turn on 2.5h later (3:30 PM) and turn off at
6:00 PM.

HOW TO USE ADVANCED FUNCTIONS

SWING function

Press Swing button

The horizontal louver will swing up and down automatically when pressing the Swing button. Press again to make it stop.

Keep pressing this button for more than 2 seconds, the vertical louver swing function is activated. (Model dependent)

Airflow direction (some models)

If continue to press the SWING button, five different airflow directions can be set. The louver can be moved at a certain range each time you press the button. Press the button until the direction you prefer is reached.

NOTE:
When the unit is off, press and hold the MODE and SWING buttons together for one second, the louver will open for a certain angle, which makes it very convenient for cleaning. Press and hold MODE and SWING buttons together for one second to reset the louver (Model dependent).

LED display

Press this button to turn on and turn off the display on the indoor unit.

Press this button more than 5 seconds (some units)

Keep pressing this button for more than 5 seconds, the indoor unit will display the actual room temperature. Press more than 5 seconds again will revert back to display the set temperature.

ECO/GEAR function (some units)

Press the GEAR-ECO button to enter the energy-efficient mode in a sequence of the following:
ECO →GEAR(75%) →GEAR(50%)→ Previous setting mode →ECO……
NOTE: This function is only available under COOL mode.

ECO operation:

Under cooling mode, press this button, the remote controller will adjust the temperature automatically to 24°C/75°F, fan speed of Auto to save energy (only when the set temperature is less than 24°C/75°F). If the set temperature is above 24°C/75°F, press the ECO button, the fan speed will change to Auto, the set temperature will remain unchanged.
NOTE:
Pressing the ECO button, or modifying the mode or adjusting the set temperature to less than 24°C/75°F will stop ECO operation.
Under ECO operation, the set temperature should be 24°C/75°F or above, it may result in insufficient cooling. If you feel uncomfortable, just press the ECO button again to stop it.

GEAR operation:
Press the ECO/GEAR button to enter the GEAR operation as follows:

75% ( up to 75% electrical energy consumption).
50% (up to 50% electrical energy consumption)
Previous setting mode

Under GEAR operation, the display on the remote controller will alternate between electrical energy consumption and set temperature.

Silence function

Keep pressing the Fan button for more than 2 seconds to activate/disable the Silence function (some units).
Due to the low-frequency operation of the compressor, it may result in insufficient cooling and heating capacity. Press ON/OFF, Mode, Sleep, Turbo or Clean button while operating will cancel the silence function.

FP function

To activate the FP function, start the air conditioner in heating mode, set the lowest available temperature (16°C/63°F), then press the down arrow button 2 times within one second.

The unit will operate at high fan speed (while the compressor is on) with a temperature automatically set to 8°C/46°F.
NOTE: This function is for heat pump air conditioners only.
If you press any buttons: ON/OFF, Sleep, Mode Fan or up/down button while the FP function is working it will be canceled.

LOCK function

Press together the Clean button and Turbo button at the same time for more than 5 seconds to activate the Lock function.
All buttons will not respond except pressing these two buttons for two seconds again to disable locking.

SET function

Press the SET button to enter the function setting, then press a SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area, press the OK button to confirm.
To cancel the selected function, just perform the same procedures as above.
Press the SET button to scroll through operation functions as follows:
Breeze Away ( ) →Sleep ( ) →Follow Me ( )→ AP mode ( ***)
[]: If your remote controller has a Fresh button or Sleep button, you can not use the SET button to select the Fresh or Sleep feature.

Breeze Away ( ) (some units):
This feature avoids direct airflow blowing on the body and makes you feel indulging in silky coolness.
NOTE: This feature is available under cool, Fan, and Dry mode only.

Sleep function ( ):
The SLEEP function is used to decrease energy use while you sleep (and don t need the same temperature settings to stay comfortable). This function can only be activated via remote control.
For the detail, see “sleep operation” in user manual.
NOTE: The SLEEP function is not available in FAN or DRY mode.
Follow me function ( ):
The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3 minutes interval. When using AUTO, COOL or HEAT modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself ) will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.

NOTE:
Press and hold the Turbo button for seven seconds to start/stop the memory feature of Follow Me function.

If the memory feature is activated “ON” displays for 3 seconds on the screen.
If the memory feature is stopped “OFF” displays for 3 seconds on the screen.
While the memory feature is activated, press the ON/OFF button, shift the mode or power failure will not cancel the Follow me function.

AP function ( ):
Choose AP mode to do wireless network configuration. For some units, it doesn’t work by pressing the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.

Clean Function

Airborne bacteria can grow in the moisture that condenses around the heat exchanger in the unit. With regular use, most of this moisture is evaporated from the unit.
By pressing the CLEAN button, your unit will clean itself automatically. After cleaning, the unit will turn off automatically. Pressing the CLEAN button mid- cycle will cancel the operation and turn off the unit. You can use CLEAN as often as you like.
NOTE: You can only activate this function in COOL or DRY mode.

Turbo Function

When you select the Turbo feature in COOL mode, the unit will blow cool air with the strongest wind setting to jump-start the cooling process.
When you select the Turbo feature in HEAT mode, for units with Electric heat elements, the Electric HEATER will activate and jump-start the heating process.

Fresh Function (some units)

Fresh function ( )
When the FRESH function is initiated, the ion generator is energized and will help to purify the air in the room.

email: info@rotenso.com

www.rotenso.com