ROTENSO Control Series SMART Air Conditioner Detector User Manual

ROTENSO Control Series SMART Air Conditioner Detector

PRECAUTIONS

WARNING
Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air- conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person could result in death or serious injury. When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that are attached to the equipment.

Read the following if you use the device in European countries:
The device can not be operated by children over 7 years old, disabled people and oraz people without experience and knowledge. Instructions should include a description of the correct and safe handling of the device and oraz information about possible dangers. Children should not play with the device. Cleaning and servicing should be carried out by authorized persons.
UTILIZATION:
Do not dispose of this product together with unsorted municipal waste. It’s necessary to transfer this type of waste for special processing. It’s illegal to throw the device together with other household waste. There are several ways to get rid of this type of equipment:w

• The city organizes electronic waste collection, you can pass the device without the cost.
• When you buy a new device the seller will accept the old device without any fees.
• Manufacturers will take the product from the buyer product without charging it with costs.
• Products of this type, contain valuable elements, it can be sold sprzedane on purchase of metals.

Throwing the device,,on wild” exposes you to the risk of losing your health. Dangerous substances from the device can penetrate to groundwater creating a danger of getting through to people’s food chain.

FEATURES

• Portable size with multi-function display
  The size is only 1809530 mm. The multi-function matrix LCD display can show you complicated information.

• Convenient for carrying and operation
  The weight is only 400g so that you can carry it easily to the site. Magnet on the back so that you can put it on any metal surface. Menu-style operations make all the detecting, checking and troubleshooting much easier.

• Easy connection
  You can connect it to inverter air conditioner directly at the terminals without disassembling the indoor or outdoor unit.

• Powerful functions
  With it you can check the communication, running parameters, error codes and set the running parameters of inverter air conditioners.

PACKING LIST

Please check if all items are inside the packing box when you get the detector.

PART NAME

1. UP button
2. DOWN button
3. OK button
4. BACK button
5. Connection selector
6. Port for high voltage connection
7. Port for low voltage connection
8. Magnet

OPERATIONS

• UP and DOWN button:
  For item selection, or page up and down in parameter inquiry mode, or increase and decrease the values in parameter setting mode. Press and hold them more than 5s if you want to adjust the values fast.

• OK button
  Confirm selection. Press and hold it for 3s, the device will directly go to the “Information Inquiry – Parameter Inquiry” function.

• Back button
  Back to the upper menu. Press and hold it for 3s, the device will go to the Primary Menu.

• Connection Selector and Connection Ports
  For selecting the right connection and power supply to the detector.

  • LNS: For a high voltage connection with the 3-core cable with a white connector, the other side is to be connected to the terminal of the inverter outdoor unit.
  • 5V: For low voltage connection with the 4-core cable with a white connector, the other side is to be connected to the Westport on the main PCB of the inverter outdoor unit.

SYSTEM MENU

Abbreviations

Menu Structure

Primary Menu| Secondary Menu| 3 rd **level Menu| Remark**
---|---|---|---

Information Inquiry

| Parameter Inquiry|  |

For 5V TestPort connection only

AD Value Inquiry|
Error Code Inquiry|

Parameter Setting

| Target Frequency|
Outdoor Fan Speed|
Open Steps of PMV|
4-way Valve|

Commu. Error Analysis

| Self-check|  |

For LNS connection only

Online Check|
Check Indoor PCB|
Check Outdoor PCB|

Commu. Simulation

|

Information inquiry

| IDU Query
ODU Query

IDU Simulator

| Mode
Target Frequency
Fan speed
Indoor Temp. T1
Evaporator Temp. T2

ODU Simulator

| Mode
Running Frequency
Condenser Temp. T3
Ambient Temp. T4
Discharge Temp. T5

OPERATION INSTRUCTIONS

ATTENTION!
Before commencing any tests, SWITCH-OFF ALL POWER SOURCES and WAIT for a MINIMUM OF 3 MINUTES to allow all capacitor voltages to decay. Before disconnecting of connecting any terminals, check that all voltages are zero. For LNS connection (Suitable for AC units with S communication) Connect this device to the void pins of outdoor wiring terminal with LNS connection cable. Make the Connection selector to “LNS”.

Note:

1. For convenience, you can move some wires from front pins to back pins so that you can connect the device on the front pins.
2. There is a clip inside the terminal of the connection wire. Always make the front side face you when you insert the terminal into the pins. Or you cannot press the clip when you want to put the terminals out of the pins.
3. Watch the sequence of L, N and S when you connect the device to the terminal.

Commun. Error Analysis

1. When the device is connected and powered on, it will carry out the communication check automatically.

2. You may get any of the below 3 feedbacks in about 40 seconds:

   • IDU commu. fault, please check the IDU and communication wire;
   • ODU commu. fault, please check ODU and communication wire;
   • Communication normal, Please press OK for information. (When OK pressed, it will go to “Commu. Simulation—Information inquiry” directly)
     Note: If you get c) result but E1 still shows, the indoor PCB is faulty and need to be replaced.

3. If you want to check the communication again, go to “Commu. Error Analysis—Online check”.

4. Self-check
   This function is to ensure the communication check function of the device is normal. Disconnect S (only L, N connected) and turn on the A/C unit, select “Commu. Error Analysis self-check”, you will get the feedback in about 10 seconds.
   Note: Self-check is unnecessary for each analysis.

Information Inquiry
Select “Commu. Simulation—Information inquiry—IDU inquiry” to check the indoor unit running parameter. Select “Commu. Simulation—Information inquiry—ODU inquiry” to check the outdoor unit running parameter.

IDU information| Data Range| ODU information| Data Range
---|---|---|---

Mode

|

OFF COOL HEAT ONLY FAN DRY

FORCE COOL DEFROST

|

Mode

| OFF COOL HEAT ONLY FAN DRY

FORCE COOL DEFROST

COOLDRY (Self-clean)

ECO

Target Frequency| 0~255| Frequency| 0~255
Room Temp.| -66.0~255| AC Input| 0~65535
Coil Temp.| -66.0~255|  |

Indoor Fan Speed

| OFF

High Middle Low Sneeze Turbo

Supper Sneeze

Auto

|

Ambient Temp.

|

-66.0~255

Set Temp.| 17-30| Coil Temp.| -66.0~255
 |  | Discharge Temp.| -66.0~255
 |  | ODU Fan speed| 0~65535
 |  | PMW steps| 0~65535

Indoor Unit Simulator
In this mode, the device can work as an indoor unit. You can set necessary parameters like values of room temperature senor T1, coil temperature sensor T2, target running frequency of compressor, mode, fan speed, even fault information and send them to outdoor unit to change the working state of it.
Note: The communication cable S should be disconnected to the indoor unit.

Outdoor Unit Simulator (Reserved)
For 5V Test Port Connection (Suitable for all inverter AC units) Remove the top cover of the inverter outdoor unit and find the main PCB. Connect this device to the TestPort on the main PCB of the outdoor unit. Make the Connection selector to “5V”.
Note: Never connect LNS and Westport at the same time.

Information Inquiry
Select “Information Inquiry—Parameter Inquiry” to check the running parameters of the inverter unit.

Indoor mode

| OFF, COOL, HEAT, ONLY FAN, DRY,

FORCE COOL, DEFROST

DC bus volt.| 0~65535
AC volt.| 0~65535
Current| 0~65535

AD Value Inquiry (Reserved)

Error Code Inquiry
You can check the error code if there is any. When error occurs, the display will show error code and the information you’re checking alternatively every two seconds.

Parameter Setting
Select “Parameter Setting”, you can set the frequency of compressor, outdoor fan speed, opening steps of electrical expansion valve and 4-way valve.

Outdoor Fan Speed

| 0~1599| DC Motor

0~1599

|

AC

Motor

| 0~Min. Speed rpm| Auto (by unit)
Min. Speed ~800 rpm| Low
800~1200 rpm| Med
1200~1500 rpm| Hi
Open Steps of EEV| 0~1599|

4-way Valve

|

0~2

| 0| Auto (by unit)
1| On
2| Off

WARNING!
DO NOT let compressor run at very high frequency or some certain frequency leading to resonance for a long time to avoid damage to compressor or the inverter control system.

Recommended set frequency range

Unit size

| Cooling Mode| Heating Mode
---|---|---
Min| Suitable| Max| Min| Suitable| Max
12K and lower| 14| 25-65| 85| 26| 35-75| 90
18-24K| 18| 25-65| 75| 26| 35-75| 85
36-60K| 20| 30-60| 70| 26| 35-70| 80

ATTENTION!
Any damage of inverter A/C units caused by the set frequency out of above range is the responsibility of the operators themselves.

email: info@rotenso.com

References

• HOME - Rotenso®

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>