OLIGHT O Bulb MC Sapphire Blue Mini LED Light User Manual
- June 6, 2024
- OLIGHT
Table of Contents
OLIGHT O Bulb MC Sapphire Blue Mini LED Light
IN THE BOX
FEATURES
- 8 light modes: White light (low), White light (high), Red, Green, Blue, Fade between colors, Cycle between colors, Flashing red.
- IPX7 waterproof and 1.5-meter impact-resistant, the Obulb MC can be a good pool light and game partner.
- Short press the intuitive rubber-coated button to switch on and cycle through 8 light modes, or long press to turn off.
- Lightweight and small, the light orb fits well in your pockets or backpacks for everyday carry.
- Operating temperature: 0℃ ~ 40℃; Storage temperature: -20℃ ~ 60℃.
SPECIFICATIONS
- All data above are test results according to ANSI/NEMA FL 1-2009 standards.
- The tests are performed using the built-in battery that is fully charged.
PRODUCT OVERVIEW
UNLOCK THE LIGHT AT FIRST USE
NOTE:
When the charging cable is connected for the first time, it is normal that the
indicator of the cable flashes red once or twice to signal charging cable
detection.
CHARGING
- Before first use please fully charge the product.
- Connect the USB end of the magnetic charging cable (MCC 1A) to an external USB power s ource, then attach the other end of the cable to the charging port at the bottom of the product. It takes 1.5 hours to fully charge.
- Charged at 4.2V/max 1A.
- The red indicator means charging, while the green indicator meanscharging completed.
- If the battery power is less than 10%, it will flash once when turn on the light or switch the modes, and it will flash once every 30 seconds to remind the user to charge it.
WARNING
Input voltage higher than 5V or voltage fluctuation may damage the IC, leading
to short-circuit and even melting of the charging interface.
BATTERY TYPE
Built-in 630mAh 3.7V Rechargeable Lithium Polymer Battery.
HOW TO USE THE ADHESIVE METAL BADGE
- Clean and dry the paste position.
- Gently and carefully peel out the protective film and DO NOT touch the sticky side.
- Paste the sticky side of the adhesive metal badge onto the desired position and press it evenly until it is fixed in place.
- Attach the Obulb MC on the adhesive metal badge.
NOTICE
- When the light is turned off, the current output mode will be memorized for next activation.
- The output brightness will decrease as the battery runs low and its voltage decreases, until the light goes off.
- DO NOT use any charging cable other than the provided MCC 1A cable.
DANGER
DO NOT drop the light or impact it heavily to protect the built-in battery.
WARNING
- DO NOT charge the product if it becomes dirty or wet after used in a wet place. Before charging, please clean and dry it.
- DO NOT let a pet play with it, in case the pet will bite and damage it.
- DO NOT hit it as a ball, which may cause irreversible damage.
- DO NOT use it as a baby toy.
- I t may be damaged or distorted at a temperature of 60℃ or higher.
HOW TO OPERATE
The button is located at the bottom of the product. It can be operated by
pressing the flat part of the bottom, or by pressing the top of the cover
provided that the product sits securely on a hard surface.
ON/OFF:
Single-click the button to turn on the light. Press and hold the button to
turn it off, and the last mode will be memorized.
CHANGE OUTPUT:
When the light is on, single click to switch the modes. The circular order is
as following: White light (low)→White light (high)→Red→Green→Blue→Fade between
colors→Cycle between colors→Flashing red→OFF → White light (low) →…
SPECIAL MODE:
Continuously click (at less than 5 seconds intervals) on the button for 20 to
200 times, the special mode will occur at random. At this time, flowing
colorful light appears, and the speed slows down over time. 30 seconds later,
it will enter into white light (low) mode automatically. To re-enter this
special mode, please repeat the above operation.
WHITE LIGHT (LOW):
When the light is off, press and hold the button for less than 2 seconds to
access white light (low) directly.
LOCK/UNLOCK:
When the light is off, press and hold the button for over 2 seconds, the light
will be locked out after a short flash. Under the lockout mode, if press the
button for less than one second, the light will be on with low white light
momentarily. To exit the lockout mode, press and hold the button for over one
second until the light is on with low white light after a quick blink.
WARRANTY
WITHIN 30 DAYS OF PURCHASE: Contact the original seller for repair or replacement.
WITHIN 2 YEARS OF PURCHASE: Contact Olight for repair or replacement.
USB MAGNETIC CHARGING CABLE: One year. This warranty does not cover normal wear and tear, modifications, misuse, disintegrations, negligence, accidents, improper maintenance, or repair by anyone other than an authorized retailer or Olight itself.
USA Customer Support
cs@olightstore.com
Global Customer Support
customer-service@olightworld.com Visit
www.olightworld.com to see our complete product line of portable illumination
tools.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>