AIE USBCDPLAY1DLX Fully Universal Application Operational Guide

AIE USBCDPLAY1DLX Fully Universal Application

INTRODUCTION

THIS SECTION WILL COVER THE PROPER MOUNTING ORIENTATION/POSITION AND ANGLE OF YOUR NEW CD PLAYER. THE UNIT MUST BE AFFIXED TO A SOLID SURFACE VIA THE PROVIDED ADHESIVE PAD. PLEASE FOLLOW THESE PRECISELY TO ENSURE PROPER FUNCTIONALITY AND FITMENT.
FAILURE TO COMPLY VOID WARRANTY, CAUSE DAMAGE TO THE UNIT AND CREATE IMPROPER PERFORMANCE AND SOUNDS

INSTALL POSITIONING CORRECT

STEP 1 WHEN CHOOSING A PROPER LOCATION FOR YOUR CD PLAYER, YOU MUST ENSURE THAT THE UNIT WILL BE FREE FROM DUST, EXCESSIVE VIBRATIONS OR ERRATIC ENVIRONMENTS SUCH AS EXTREME HEAT FROM IN-VEHICLE COMPONENTS (HEATER VENTS ETC.)

STEP 2 ONCE CHOSEN, MAKE SURE THE MOUNTING POSITION IS WITHIN COMPLIANCE AS REQUIRED BY THE MANUFACTURER. THIS IS AS FOLLOWS:

HORIZONTAL POSITION IS DEFINED AS CD SLOT BEING ON THE TOP SIDE OF THE UNIT WITH THE ARROW PORTION OF THE EJECT BUTTON POINTING UP

VERTICAL POSITION IS DEFINED AS CD SLOT FACING UP. UNIT ANGLED  NO GREATER THAN ZERO DEGREES  (PERFECTLY STRAIGHT & UPRIGHT)  THE MOUNTED ANGLE MUST NOT EXCEED PAST ZERO DEGREES TO AVOID DAMAGE/ABUSE TO THE UNIT AND CAUSE UNIT TO POSSIBLY  MAKE IMPROPER FUNCTIONING SOUNDS.

ANY ANGLE ZERO TO 90 DEGREES (CORRECT)

INSTALL POSITIONING NOT CORRECT

INSTALLATION

Thank you for your purchase of the USB CD player kit. This unit has 3 methods of installation and is based on the configuration of your vehicle. Please reference each of the 3 installation techniques to find the proper one that suites your vehicle. Please ensure that you are only utilizing the parts intended for your vehicle configuration to ensure proper functionality.

KIT CONTENTS

INSTALL ATION ADVISORY

PLEASE DO NOT ATTEMPT INSTALL ATION WITHOUT READING THES INSTRUCTIONS FIRST. FOR QUESTIONS REGARDING THIS INSTALLATION OR YOUR CONFIGURATION, PLEASE CONTACT YOUR AUTHORIZED DE ALER FOR FURTHER DETAILS AND PRODUCT SUPPORT.

PLEASE READ EACH OF THE 3 INSTALLATION CONFIGURATIONS CAREFULLY TO IDENTIFY WHICH IS BEST SUITABLE FOR YOUR VEHICLE. THIS SECTION WILL COVER INSTALL OPTION 1 OF 3 WHICH IS A DIRECT USS CONNECTION. PLEASE REFER TO THE ENCLOSED FIT CHART TO SEE IF YOUR VEHICLE IS APPLICABLE. IF YOU DO NOT FIND YOUR VEHICLE, PLEASE PROCEED TO INSTALL OPTION 2 OF 3 OR 3 OF 3.

INSTALL OPTION 1 (REFER TO FIT CHART)

STEP 1 TAKE USB CD PLAYER AND FIND SUITABLE LOCATION. TRY TO FIND A LOCATION THAT DOES NOT REQUIRE ANY USB EXTENSION CABLE IF POSSIBLE.

STEP 2 THE CD PLAYER CAN MOUNT VERTICALLY OR HORIZONTALLY. PLEASE MAKE SURE IF MOUNTINGVERTICALLY THAT THE UNIT IS A COMPLETE 90 DEGREES. ONCE A LOCATION IS CHOSEN, TAKE THE PROVIDED MOUNTING TAPE AND PROCEED TO PEEL AND STICK IT TO THE CD PLAYER IN A DISCREET BUT STABLE FLAT SURFACE ON THE TOP OR BOTTOM OF THE UNIT. THEN PEEL THE OPPOSITE SIDE AND PROCEED TO STICK IT TO THE CHOSEN SURFACE MAKING SURE ENOUGH SURFACE CONTACT IS MADE TO STABILIZE THE UNIT  AND KEEP IT FROM MOVING ONCE SECURED.

STEP 3 CONNECT THE CD PLAYER USB PLUG COMING OUT OF THE REAR OF THE CD PLAYER UNIT AND CONNECT IT TO YOUR VEHICLES DATA BASED USB CONNECTION INPUT. PLEASE MAKE SURE YOU ARE CONNECTING TO YOUR DATA PLUG AND NOT A USB POWER ONLY PLUG. THIS WILL BE THE SAME CONNECTION(S) THAT YOUR SMART DEVICE OR USB MEDIA MUSIC STICK WOULD CONNECT TO FOR RADIO PLAYBACK AND CONTROL.

STEP 4 ONCE CONNECTED, YOU MAY INSERT A DISC INTO THE USS CD SLOT. IF PROPERLY CONNECTED, THE UNIT WILL ACCEPT THE CD AND BEGIN THE LOADING PROCESS.

STEP 5 ONCE THE CD IS IDENTIFIED AND IS A PROPERLY FORMATTED CD, THE UNIT MAY BEGIN TO AUTO PLAY. THIS PROCESS WILL BE PART OF THE INDEX PROCESS AND CANNOT BE INTERRUPTED FOR AT LEAST 15 SECONDS. THE INDEXING PROCESS IS CREATING A TABLE OF CONTENTS FOR YOUR RADIO TO IDENTIFY AND IF THIS IS INTERRUPTED IN ANY WAY BY JUMPING TO A SONG OR PAUSING THE AUTO PLAYBACK, YOU WILL CORRUPT THE CDS PLAYBACK CAPABILIT Y AND YOU MUST START OVER. PLEASE REFER TO THE TROUBLESHOOTING SECTION OF THIS GUIDE FOR HOW TO CORRECT THE INDEXING CORRUPTION PROCESS.

STEP 6 ONCE INDEXING IS COMPLETE, YOU MAY PROCEED TO CHOOSE THE SONG OF YOUR CHOICE AND YOU WILL HAVE FULL CONTROL OF IT WITH FF, REW, PLAY/PAUSE

PARTS NEEDED

THIS SECTION WILL COVER INSTALL OPTION 2 OF 3. YOUR VEHICLE MUST BE EQUIPPED WITH A 3.5MM MIN/JACK AUDIO CONNECTION AND A 12 VOLT POWER PORT SHOWN HERE. IF EQUIPPED, PLEASE PROCEED WITH INSTALLATION INSTRUCTIONS BELOW.

INSTALL OPTION 2

STEP 1 TAKE USB CD PLAYER AND FIND SUITABLE LOCATION. TRY TO FIND A LOCATION THAT DOES NOT REQUIRE ANY USB EXTENSION CABLE IF POSSIBLE.

STEP 2 THE CD PLAYER CAN MOUNT VERTICALLY OR HORIZONTALLY. PLEASE MAKE SURE IF MOUNTING VERTICALLY THAT THE UNIT IS A COMPLETE 90 DEGREES. ONCE A LOCATION IS CHOSEN, TAKE THE PROVIDED MOUNTING TAPE AND PROCEED TO PEEL AND STICK IT TO THE CD PLAYER IN A DISCREET BUT STABLE FLAT SURFACE ON THE TOP OR BOTTOM OF THE UNIT. THEN PEEL THE OPPOSITE SIDE AND PROCEED TO STICK IT TO THE CHOSEN SURFACE MAKING SURE ENOUGH SURFACE CONTACT IS MADE TO STABILIZE THE UNIT AND KEEP IT FROM MOVING ONCE SECURED.

STEP 3 LOCATE THE CD ADAPTER CONTROLLER. REMOVE IT FROM ITS BAG AND UNRAVEL THE CABLING. NOTE THAT YOU MAY HAVE EXCESS CABLING THAT MAY CHOOSE TO EITHER BUNDLE TOGETHER OR TUCK AWAY IN A DISCREET, LESS VISIBLE LOCATION BUT KEEPING ENOUGH SLACK ACCESSIBLE TO LOCATE EACH COMPONENT ACCORDINGLY

WIRING PROCEDURE

1. CONNECT CD PLAYER USB TO USB INPUT CONNECTION ON CD ADAPTER.
2. LOCATE CD CONTROL AND FIND EASILY REACHABLE LOCATION. PEEL DOUBLE STICK TAPE PROTECTOR FROM BOTTOM AND STICK TO FLAT, CLEAN SURFACE
3. LOCATE AUX IN AUDIO CONNECTION ON RADIO FACEOR INSIDE CENTER CONSOLEOR BELOW RADIO. CONNECT3.5MM AUX AUDIO OUTPUT FROM CD ADAPTER CONTROL
4. LOCATE 12V POWER ADAPTER AND PROCEED TO INSERT PROVIDED POWER ADAPTER INTO 12V CAR POWER RECEPTACLE. MAKE SURE POWER IS ON AND ON/OFF SWITCH IS IN THE ON POSITION AND TEST CD PLAYER.

THIS SECTION WILL COVER INSTALL OPTION 3 OF 3. YOUR VEHICLE MUST BE EQUIPPED WITH A USB DATA INPUT CONNECTION AND A 12 VOLT POWER PORT SHOWN HERE. IF EQUIPPED, PLEASE PROCEED WITH INSTALLATION INSTRUCTIONS BELOW.

INSTALL OPTION 3

STEP 1 TAKE USB CD PLAYER AND FIND SUITABLE LOCATION. TRY TO FIND A LOCATION THAT DOES NOT REQUIRE ANY USB EXTENSION CABLE IF POSSIBLE.

STEP 2 THE CD PLAYER CAN MOUNT VERTICALLY OR HORIZONTALLY. PLEASE MAKE SURE IF MOUNTING VERTICALLY THAT THE UNIT IS A COMPLETE 90 DEGREES. ONCE A LOCATION IS CHOSEN, TAKE THE PROVIDED MOUNTING TAPE AND PROCEED TO PEEL AND STICK IT TO THE CD PLAYER IN A DISCREET BUT STABLE FLAT SURFACE ON THE TOP OR BOTTOM OF THE UNIT. THEN PEEL THE OPPOSITE SIDE AND PROCEED TO STICK IT TO THE CHOSEN SURFACE MAKING SURE ENOUGH SURFACE CONTACT IS MADE TO STABILIZE THE UNIT AND KEEP IT FROM MOVING ONCE SECURED.

STEP 3 LOCATE THE CD ADAPTER CONTROLLER AND AUX USB AUDIO CABLE. REMOVE IT FROM ITS BAG AND UNRAVEL THE CABLING. NOTE THAT YOU MAY HAVE EXCESS CABLING THAT MAY CHOOSE TO EITHER BUNDLE TOGETHER OR TUCK AWAY IN A DISCREET, LESS VISIBLE LOCATION BUT KEEPING ENOUGH SLACK ACCESSIBLE TO LOCATE EACH COMPONENT ACCORDINGLY

WIRING PROCEDURE

1. CONNECT CD PLAYER USB TO USB INPUT CONNECTION ON CD ADAPTER.
2. LOCATE CD CONTROL AND FIND EASILY REACHABLE LOCATION. PEEL DOUBLE STICK TAPE PROTECTOR FROM BOTTOM AND STICK TO FLAT, CLEAN SURFACE
3. LOCATE USB AUX AUDIO CABLE PROVIDED CONNECT TO AN OPEN DATA USB RADIO INPUT AND LOCATE 3.5MM AUDIO OUTPUT FROM CD CONTROLLER. CONNECT TOGETHER. YOU MAY NEED TO PERFORM AUDIO CALIBRATION. PLEASE SEE CALIBRATE SECTION
4. LOCATE 12V POWER ADAPTER AND PROCEED TO INSERT PROVIDED POWER ADAPTER INTO 12V CAR POWER RECEPTACLE. MAKE SURE POWER IS ON AND ON/OFF SWITCH IS IN THE ON POSITION AND TEST CD PLAYER.

NOTE: IF YOU DO NOT HAVE AUDIO PROCEED TO THE AUDIO CALIBRATION SECTION OF INSTRUCTIONS

There are 3 Types of installation for the USBCDPLAY1DLX

1. Using the single USB cable and assuming you have confirmed the vehicle you are attempting installation on is covered by the fit chart .JPG, simply connect the USB cable, mount the unit and you are done.
2. If the vehicle is not on the fit chart .JPG , proceed to using the CD player adapter. Plug the USB cable from the USB CD player into the provided input on the adapter, connect ACC power and ground to the adapter power and ground leads, take the provided 3.5mm mini jack audio output and plug it into the vehicles provided 3.5mm audio input and then mount the provided dial controller somewhere convenient and accessible and you are complete.
3. If the vehicle is not on the fit chart .JPG and does not have a 3.5mm mini jack audio input , take the USB AUX cable that is provided in the box and proceed to connect that to an open USB data input port of your vehicle. Please make sure the USB port you choose is for data and not just for charging only. This adapter is designed to an emulator which will adapt and convert the USB port to a 3.5mm mini jack input. This will allow the 3.5mm mini jack audio output connector from the CDP-1 to connect to and provide audio to your factory radio system.

Install Summary Instructions for adapter:

• Connect 3.5mm audio plug to car audio input
• Connect USB to CD player USB
• Put control knob in easy access location
• Connect red wire to ACC 12V
• Connect white wire to chassis ground

Functions for controller knob:

• Knob quick left – previous song Knob quick right – next song
• Knob push – play/pause
• Knob hold left – volume down
• Knob hold right – volume up

First, please check the Vehicle Fit Guide on the site page located in the images and check to make sure you ordered the correct model# for your vehicle. Also please check the Factory Requirements column to make sure the CD Player will work with your specific vehicle radio. The CD Players will not necessarily work with all radio types.

If the vehicle does not find the USB CD Player:

Check to make sure the CD Player is plugged into the USB port for data and not the USB port for charging. The charging port is usually marked with a lighting symbol, but it could be faint and hard to see. The charging port will not work to connect the CD Playe r to the car.
Also, make sure to disconnect any USB extensions and plug in the CD Player directly. Some vehicles have sensitivity to USB cable lengths.

If the CD will not play or skips:

Step 1 Insert CD

Step 2 WAIT. If the unit begins to auto play, still WAIT. The indexing process is being performed whereby the USB hub in your vehicle is building a table of contents to follow. This can take up to 20 seconds. If at any time this indexing process is interrupted by skipping to a song or pausing or unplugging or changing the source, it will interrupt the table of contents and it will skip songs, miss songs, play 10 sec then stop or just not work at all.
Ford and GM display on the screen that the unit is indexing and to “please wait”. It will even tell you when the indexing is complete. Other vehicles may not display anything on the screen. However, you must still wait for at least 20 seconds for the CD to index before pushing any buttons or trying to fast forward, skip, play, etc.
If the indexing process gets interrupted , you must eject the disc. Then insert a different disc to purge the vehicle USB hub. Let it index for that CD, then eject and reinsert the original CD. Let the original CD index again. Once finished indexing, it will be ready to listen to.

• These CD Players work with many vehicles and have an extremely low defect rate if properly installed. Please make sure you let every CD index for 20 seconds before trying to fast forward, skip, play, etc.
• Make sure you have read the Quick Reference Set-up Guide included with the CD Player and also located online in the images, as well as the on line Troubleshooting Guide located in the images. If you are still experiencing issues, please call customer service at: (442) 400-9489 for more assistance.

FAQs

Does this work with mmi, mib-3, and olufsen systems in Audi vehicles?****

Yes, it will, as it is a universal application whose objective is to give you a successful CD player installation result regardless of the automobile design.

I’ve used several variations of this CD player. Why must I allow the player 45 minutes to relax when they stop playing after an hour?****

I don’t know why yours stops working. In between pit stops, mine continues to play.

Can you use an AIE USBCDPLAY1DLX USB CD drive in a car?****

Your car’s most recent model most likely contains a USB port. You should buy and connect a USB adaptor for a CD player. You should think about a power supply. Select a player that runs on batteries or search for a plug-in wire that your car will take.

How can I use the AIE USBCDPLAY1DLX CD player in my car?****

After it has started, put your favourite CD in the CD player. Your portable CD player and the aux port in your automobile are connected by two ends of aux cables, respectively. Your car’s sound system should be set to “AUX” mode. Select “PLAY” on your CD player and turn the volume up.

Can you use an AIE USBCDPLAY1DLX USB CD drive in a car?****

Your car’s most recent model most likely contains a USB port. You should buy and connect a USB adaptor for a CD player. You should think about a power supply. Select a player that runs on batteries or search for a plug-in wire that your car will take.

How can I use the AIE USBCDPLAY1DLX CD player in my car?****

After it has started, put your favourite CD in the CD player. Your portable CD player and the aux port in your automobile are connected by two ends of aux cables, respectively. Your car’s sound system should be set to “AUX” mode. Select “PLAY” on your CD player and turn the volume up.

How should an AIE USBCDPLAY1DLX car CD player be maintained?****

Make use of a soft-bristled brush to remove all of the loose debris and dust. Use an electric fan or a compressed air can to remove tiny particles. Use an interior cleaner to wipe the CD player panel’s surface.

AIE USBCDPLAY1DLX CD players are distributed in what ways?****

Press and hold the EJECT button as you turn your ignition to the accessory power position. Try gently inserting a blank disc about an inch into the player and continually pressing the EJECT button to get both discs to come out of the machine at once.

What AIE USBCDPLAY1DLX CD player is the best fit for my Hyundai Palisade?****

Examine the description to see if the item will fit in your automobile. It worked because I adhered strictly to the instructions.

What went wrong with my car’s AIE USBCDPLAY1DLX CD player?****

Usually, the CD’s scratched or broken tracks are to blame. Test a few more current CDs to see if the skipping behaviour persists before concluding that the player is the issue. If not, you’ll need to consider repairing or cleaning the disc itself so that it resumes playing normally.

What does the focus error on the AIE USBCDPLAY1DLX CD player mean?****

This indicates a problem with the eye that scans the data lines on the disc. Before it can start functioning once again, it needs to be cleaned and calibrated by professionals.

Why is there a report of an error from the CD player AIE USBCDPLAY1DLX?****

When inserting the disc into the disc tray, make sure the playback side is facing downward. If the disc has damage—such as scratches, breaks, or is dirty with smudges or fingerprints—the player might not be able to read it. To fix the issue, wipe the disc with a soft, dry cloth.

How long is the lifespan of an AIE USBCDPLAY1DLX CD player?****

Hi-fi systems should live much longer, roughly 10 to 20 years, or at least the speakers, turntable, and amplifier components of those systems. CD players don’t live as long, while having a lifespan of five to ten years.

Video

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>