Idpoo B08TBDH8X4 Wireless Hitch Camera Magnetic with 5-Inch IPS Monitor User Manual

Idpoo B08TBDH8X4 Wireless Hitch Camera Magnetic with 5-Inch IPS Monitor

INTRODUCTION

The user manual has a detailed description on how to correctly use the hitch camera and provides detailed product information, including operation, installation precautions and technical specifications.

PACKAGE LIST

• 1x wireless magnetic hitch camera
• 1x 5”color HD IPS monitor
• 2x 2.4G antenna(5DB)
• 1x 2.4G antenna extension cable(10ft)
• 1x CAR charger cable(incar)
• 1x USB charger cable(indoor)
• 1x fan-shaped mount bracket
• 1x mount metal plates with strong adhensive(Optional)
• 1x magnetic car vent mount kit(Optional) Note: The actual parts list may have small changes based on customer needs

FEATURE

• Wireless transmission up to 200ft range in open area
• Camera magnetic base for instant mounting and removing
• Built-in rechargeable long life battery for about 15Hrs of continuous use.
• Color HD 5″ IPS monitor
• Install in minute ready to use no screw necessary no wiring
• With battery display and wireless signal strength indicator.

BEFORE BEGINNING INSTALLATION

Please indoor 3-minute simple basic function verification
before actual installation on the trucks/trailers/RVs.

FUNCTIONS OF EACH PART

See package list figure

CAMERA INSTALLATION

Recommended installation placement that close to hitch ball and adjust the camera angle of viewing comfort.

MONITOR INSTALLATION

Recommended installation location of viewing comfort. and adjust mounting angle to allow optimum driver viewing comfort.

START TO USE

1. Turn on the camera by long press the power button(hold 3s), then the red led will turn on.
2. You will view the camera image on your monitor.

FINISH/END TO USE

Turn off the camera by long press the power button, then the 4 led will flash once at the same time, avoiding the camera is always on and draining battery.

FUNCTIONS AND OPERATION

1. Menu setting:
   Press the “MENU” button on the panel, can open the option of the “contrast”, “saturation” and “brightness” in menu

2. Flip setting:
   Press “FLIP” button set UP, Down,
   Left(frontview),Right(rearview) flip image

3. ParkingLine setting:
   Press “ParkingLine ” button, parking line setting on/off.

4. Camera pairing:
   Long press the “Pairing” button on the panel to enter the pairing state (the state lasts for 10S) and display “pairing” (as shown in the figure below). In the pairing state, interrupt the power supply of the camera and re-power it, It will show a text“Successfully Pairing”, or will show “Pairing Fail” means failure to pair, needs to pair again;

5. Support camera charge methods:
   CAR charge cable/USB charge cable/power cable.

6. Test signal strength:
   Put the monitor and the camera at the intended position to test signal strength.

WIRING DIAGRAM

SPECIFICATION & DIMENSION

Wireless camera

Wireless monitor

TROUBLESHOOTING

If you have any questions about this product, Pls send us [email protected]

1. No signal
2. Please check the camera is turn-on or draining battery.
3. Please check the antenna are plugged on the camera.
4. Please check the angle of the antenna.
5. Please check metal obstacles near the antenna.
6. Pairing information is missing or wrong, please re-pair.
7. Out of range, please add an antenna extension cable or change the camera mounting location
8. No picture
9. Pairing information is missing or wrong, please re-pair.
10. Out of range, the wireless signal is blocked too badly or poor signal, please add an antenna extension cable or change the camera mounting location.
11. Please check low voltage red light blinking(flash) indicator, please charge first!
12. Freezes and disconnects / Unstable / static video
13. Out of range, Please add an antenna extension cable or change the camera mounting location.
14. The wireless signal is blocked too badly or poor signal, please add an antenna extension cable or change the camera mounting location.
15. Fuzzy picture,Not clear
16. Please remove the camera lens protector to get best picture quality after install.
17. Please check whether wipe off the camera lens.
18. The mounted camera slides or falls Please check whether remove the film from the camera base,
19. for the plastic/aluminum/glass/wood surface Please use the mount metal plates with strong adhensive,
    Notes: It takes 72 hours to reach the best effect after pasting.

FAQs

Q: Battery life
A: charged time:8 hour(80%), daytime continuous work time:18 hours,night continuous work time:15 hours,cold weather will consume power a little faster.
Q: How to check the camera turn-on/turn-off mode?
A: Please check after short press the power button, turn-on mode when the red led is on status,turn-off mode or drain battery when the red led is off status.
Q: How to check whether the camera is draining the battery?
A: the 4 leds of the camera are always off by long-press the power button hold 3 second.
Q: How to turn on/off the camera?
A: turn on: the red led on when long-press the power button hold 3 second; turn off: the full four led blink on and then all off when long-press the power button hold 3 second.
Q:How to check the battery?
A: In power-on mode, Please check whether the four leds of the camera indicator by short press the power button,
one red led on plus three green led on(about 100%),
one red led on plus two green led on(about 75%),
one red led on plus one green led on(about 50%),
one red led on plus three green led off(about 25%),full four led off (about 0%).
Q:How to check low voltage of the “No picture /Fuzzy picture”
A: the red LED blinking(flash) indicator, please charge first!

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>