Idpoo Dual Wireless Magnetic Camera User Manual

June 9, 2024
Idpoo

Idpoo Dual Wireless Magnetic Camera

INTRODUCTION
The user manual has a detailed description of how to correctly use the hitch camera and provides detailed product information, including operation, installation precautions, and technical specifications.

PACKAGE LIST

  • 2x wireless camera
  • 1x HD monitor
  • 3x 2.4G antenna(5DB)
  • 1x 2.4G antenna extension cable(10ft)
  • 1x CAR charger cable(incar)
  • 1x USB charger cable(indoor)
  • 1x fan-shaped mount bracket
  • 2x mount metal plates with strong adhensive(Optional)
  • 1x magnetic car vent mount kit(Optional)

Note: The actual parts list may have small changes based on customer needs

FEATURE

  • Wireless transmission up to 200ft range in an open area
  • Camera magnetic base for instant mounting and removing
  • Built-in rechargeable long-life battery for about 15Hrs of continuous use.
  • Color HD 7″ IPS monitor
  • Install in a minute ready to use no screw necessary no wiring
  • With battery display and wireless signal strength indicator.

BEFORE BEGINNING INSTALLATION

Please do indoor 3-minute simple basic function verification before actual installation on the trucks/trailers/RVs.

FUNCTIONS OF EACH PART

CAMERA INSTALLATION

Recommended installation placement that closes to the hitch ball and adjusts the camera angle of viewing comfort.

MONITOR INSTALLATION

The recommended installation location of viewing comfort. and adjust the mounting angle to allow optimum driver viewing comfort.

START TO USE

  1. Turn on the camera by long pressing the power button(hold 3s), then the red led will turn on.
  2. You will view the camera image on your monitor.

FINISH/END TO USE

Turn off the camera by long pressing the power button, then the 4 led will flash once at the same time, avoiding the camera is always on and draining the battery.

FUNCTIONS AND OPERATION

  1. Menu setting:
    Press the “MENU” button on the panel, can open the option of “contrast”, “saturation” and “brightness” in the menu.

  2. Flip setting:
    Press the “FLIP” button to set UP, Down, Left(front view), and Right(rearview) flip image

  3. ParkingLine setting:
    Press the “ParkingLine ” button, parking line setting on/off.

  4. Camera pairing:
    Firstly, Short press the “Pairing” button on the panel enter to the single- channel state; Secondly, Long press the “Pairing” button to enter the pairing state (the state lasts for 10S) and display “pairing” (as shown in the figure below). In the pairing state, interrupt the power supply of the camera and re- power it, It will show the text“Successfully Pairing”, or will show “Pairing Fail” which means failure to pair, needs to pair again;

  5. Support camera charge methods:
    CAR charge cable/USB charge cable/power cable.

  6. Test signal strength:
    Put the monitor and the camera in the intended position to test signal strength.

  7. Split screen setting:
    Short press the “Pairing” button on the panel to toggle from one split screen(full screen) and dual split screen.

WIRING DIAGRAM

SPECIFICATION & DIMENSION

Wireless camera

Sensor 1/2.7” Color CMOS
Resolution 1280x720P
System P/N auto
Viewing Angle 120˚
Night Vision 4 infra-red lights
Transmission Type Digital Wireless (2400-2483.5MHz)
Transmission Range up to 200ft in open area
Waterproof Level IP67
Operation Temperature –20℃ ~ 70℃
Battery Capacity 6400mAh
Battery working time up to 18 hrs daytime/15hrs night
Battery standby time up to 360 hrs daytime/68 hrs night
Battery Charging time 8 hrs(80%),16 hrs(100% full)
Battery capacity indicator 4 LED lights
Built-in Strong Magnet Base Yes
Camera adjustable angle 0-100 degree
Dimensions 7445.556.5mm

Wireless monitor

Lcd size 7” color IPS pannel
Resolution 1024×3(RGB)x600
View angle U/D:85˚;L/R:85˚
Power Supply DC9-36V
Power Consumption <3W
Working temperature -20~+70℃
Transmission Type Digital Wireless (2400-2483.5MHz)
Transmission Range up to 200ft in an open area

TROUBLESHOOTING

If you have any questions about this product/free to extend your warranty to 12 Months, contact: csderk@outlook.com.

  1. No signal

  2. Please check the camera is turned on or draining the battery.

  3. Please check the antenna is plugged into the camera.

  4. Please check the angle of the antenna.

  5. Please check metal obstacles near the antenna.

  6. If pairing information is missing or wrong, please repair it.

  7. Out of range: please add an antenna extension cable or change the camera mounting location, The extension antenna for the camera or monitor bypasses obstacles and allows the camera to be placed in an obstructed location with the antenna positioned in an unobstructed area.

  8. No picture

  9. If pairing information is missing or wrong, please repair it.

  10. Out of range, the wireless signal is blocked too badly or poor signal, please add an antenna extension cable or change the camera mounting location.

  11. Please check the low voltage red light blinking(flash) indicator, please charge first!

  12. Freezes and disconnects/Unstable/static video

  13. Out of range, Please add an antenna extension cable or change the camera mounting location.

  14. If the wireless signal is blocked too badly or poor signal, please add an antenna extension cable or change the camera mounting location.

  15. Fuzzy picture, Not clear

  16. Please remove the camera lens protector to get the best picture quality after installation.

  17. Please check whether wipe off the camera lens.

  18. The mounted camera slides or falls
    Please check whether remove the film from the camera base,

  19. for mounting non-magnetic surface(plastic/aluminum/glass/wood surface)
    Please use the mount metal plates with strong adhensive,

Notes: It takes 72 hours to reach the best effect after pasting.

FAQs

Q: Battery life
A: charged time:8 hours (80%), daytime continuous work time:18 hours, night continuous work time:15 hours, cold weather will consume power a little faster.

Q: How to check the camera turn-on/turn-off mode?
A: Please check after short pressing the power button, turn-on mode when the red led is on status, turn-off mode or drain battery when the red led is off status.

Q: How to check whether the camera is draining the battery?
A: The 4 leds of the camera are always off by long pressing the power button hold 3 seconds.

Q: How to turn on/off the camera?
A: turn on: the red led on when long press the power button hold 3 seconds; turn off: the full four led blink on and then all off when long press the power button hold 3 seconds.

Q: How to check the battery?
A: In power on mode, Please check whether the four leds of the camera indicator by short pressing the power button, one red led on plus three green led on(about 100%), one red led on plus two green led on(about 75%), one red led on plus one green led on(about 50%), one red led on plus three green led off(about 25%), full four led off (about 0%).

Q: How to check the low voltage of the “No picture /Fuzzy picture”
A: the red LED blinking(flash) indicator, please charge first!

contact: csderk@outlook.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals