PNI DK101 Control Access Keypad with Proximity Caed Reader User Manual

PNI DK101 Control Access Keypad with Proximity Caed Reader

PRODUCT DESCRIPTION

TECHNICAL SPECIFICATIONS

FACTORY DEFAULT VALUES

OPTIC AND SOUND INDICATORS

Normal working mode:

• command confirmation: short beep
• invalid command: long beep

Programming mode

• green LED on
• command confirmation: 2 short beeps
• invalid command: 3 short beeps

FUNCTIONS AND SETTINGS PROGRAMMING

• Enter programming mode: press [#] + [programming PIN] (the default programming PIN is 881122). You will hear 2 confirmation beeps and the green LED will light.

• Change programming PIN: press [0] + [new programming PIN] + [confirm new PIN]. You will hear 3 confirmation beeps.

• Door open mode selection

• card or PIN: press [1] + [0]. You will hear 2 confirmation beeps.

• card + PIN: press [1] + [1]. You will hear 2 confirmation beeps.
  NOTE: In card or PNI door open mode the PIN is either the public one or a private one (up to 999).

• Door open time setting: press [2] + [TT], TT = time interval in seconds. You will hear 2 confirmation beeps.
  For example, if the door open time is 3 sec then TT = 03

• Change public PIN: press [3] + [new 4 digit PIN]. You will hear 2 confirmation beeps.

• Tamper switch:

• disable: press [4] + [0]. You will hear 2 confirmation beeps.

• enable: press [4] + [1]. You will hear 2 confirmation beeps.

• Enrolling EM cards: press [5] + [3 digit index code] + present card 1 + present card 2 ……… + [3].
  After every presented card you will hear 3 confirmation beeps.

• the 3 digit index code (001 – 999) is important for deleting a lost card.

• when enrolling multiple cards the index code will be increased automatically.

• the default private PIN for every card is 0000

• Door contact:

• disable: press [6] + [0]. You will hear 2 confirmation beeps.

• enable: press [6] + [1] to deactivate the tamper switch. You will hear 2 confirmation beeps

• NOTE: The door contact must be purchased separately.

• Delete cards:

• Delete card by index code: press [7] + [index code 1] + [index code 2] + ..+ [#]. After every index code you will hear a long confirmation beep.

• Delete card by presenting it: press [7] + present card 1 + present card 2 + … + [#]. After every card you will hear a long confirmation beep.

• Delete all cards: restore factory default settings

• NOTE: The private PIN associated to a card will be deleted at the same time with the card.

• Modify private PINs:

• disable: press [1] + [2]

• enable: press [1] + [3] NOTE: Modify private PIN: exit programming mode the long press [#] (the green LED will light) + present card + [old private PIN] (default 0000) + [new private PIN] + [repeat new private PIN]. You will hear 2 confirmation beeps.

• Door contact alarm:

• disable: press [8] + [0]. You will hear 2 confirmation beeps.

• enable: press [8] + [1]. You will hear 2 confirmation beeps.
  NOTE: Enabling this option will cause the keypad to sound when the door is left open or when the door is not unlocked from the keypad.

• Alarm delay time: press [8] + [2] + [TT], TT = time interval in seconds. You will hear 2 confirmation beeps.
  For example, if the door open time is 3 sec then TT = 03.
  NOTE: This function can be used after enabling the door contact.

• Exit programming mode: press [#]. You will hear 3 confirmation beeps.

• Cancel command: press [#]

• Restore factory default: press [8] + [6]

• Reset programming PIN: short the J2 jumper to reset programming PIN to factory default.

USER INSTRUCTION

Card or PIN door open mode:

• present card or type your private PIN on the keypad

Card + PIN door open mode:

• present card the type your private PIN on the keypad

FREQUENTLY ASKED QUESTIONS

After the lock is opened there are 8 short beeps| – the keypad needs higher voltage, please check

the power supply

---|---
The card reading distance is to short or the card

can’t be read

| – the electric current is to low, please check the power supply
After presenting the card there are 3 beeps and the

lock doesn’t open

| – the keypad works only in card+PIN mode

– the keypad is in programming mode

Present an enrolled card does not unlock the door| – check if the door contact is in alarm mode. Disable door contact.
Can’t enter programming mode and a long beep is

heard

| – multiple buttons were pressed before trying to enter programming mode. Wait a few seconds then try again
After pressing [5] there are 3 beeps| – card memory full
After pressing [5] + [index code] there are 3 beeps| – the index code is already in use
---|---
The keypad exited programming mode by itself| – if there is no input in 20 sec the keypad will

automatically exit programming mode

WIRING DIAGRAM WITH TIME DELAY POWER SUPPLY

WIRING DIAGRAM WITH SIMPLE POWER SUPPLY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>