TRIPP-LITE B006-HD2UA2 2/4-Port USB 3.0 4K HDMI Dual Display KVM Switch User Guide

TRIPP-LITE B006-HD2UA2 2/4-Port USB 3.0 4K HDMI Dual Display KVM Switch

Package Contents

• B006-HD2UA2 or B006-HD2UA4 HDMI Dual Display KVM Switch

• Foot Pads (x4)

• Power Adapter

• Remote Port Selector

• Quick Start Guide*

• The complete Owner’s Manual is available on Tripp Lite’s website: tripplite.com/support.

Product Features

Front

Rear

1. Mode Selection Pushbutton
2. Port Selection Pushbuttons
3. Port LEDs
4. Audio Jacks
5. USB 3.1 Gen1 Peripheral Port
6. DCC Port (Daisy Chain Control)
7. Console Ports Section
8. KVM Ports Section
9. Power Jack
10. Audio Jacks
11. USB 3.1 Gen1 Peripheral Port
12. DCC Switch
13. Remote Port Selector Jack
14. Grounding Terminal

Installation

Note: B006-HD2UA4 shown. Installation steps are the same for the B006-HD2UA2 model.
To prevent damage to your installation from power surges or static electricity, it is important that all connected devices are properly grounded.

1. Ground the unit by connecting one end of a grounding wire o the Grounding Terminal and the other end to a suitable grounded object.
   Note: Do not skip this step. Proper grounding helps to prevent damage to the unit from power surges or static electricity.

2. Plug your USB keyboard and USB mouse into the USB console ports from the Console Ports Section located on the unit’s rear panel.

3. Plug your HDMI monitors into the HDMI console ports from the Console Ports Section located on the unit’s rear panel and power on the monitors.

4. Plug your microphone and speakers into the Audio Jacks located on the unit’s front panel. Audio cables are required to connect to the CPU for this connection to work.

5. Plug your secondary microphone and speakers into the Audio Jacks located on the unit’s rear panel.
   Note: The microphone and speakers plugged into the front panel have priority over those plugged into these jacks.

6. With a user-supplied HDMI cable, plug the HDMI connector into any available HDMI port on the KVM Ports Section of the switch (CPU1, CPU2, etc.). Then, plug the USB 3.0 cable, microphone cable and speaker cable into their corresponding ports. With a second user-supplied HDMI cable, plug the HDMI connector into the HDMI port in the same KVM Ports Section of the switch.
   Note: Verify that all the connectors are in the same KVM Ports Section (all in CPU1, all in CPU2, etc.).

7. At the other end of the cables from step 6, plug the HDMI cables, USB 3.0 cable, microphone cable, and speaker cable into their respective ports on the computer. Repeat steps 6, and 7 for each dual-screen PC system you are installing.

8. (Optional) Plug your USB peripherals into the front or rear USB 3.1 Gen1 Peripheral Ports.

9. (Optional) If you choose to use the remote port selector, plug its cable into the Remote Port Selector Jack, located on the unit’s rear panel.

10. Plug the power adapter included with the KVM switch into an AC power source, then plug the power adapter cable into the switch’s Power Jack.

11. Power on the computers.

Operation

Manual Switching
To bring complete focus (audio, KVM, and USB) to a computer, either:

• Press the Port Selection Pushbutton that corresponds to that computer; or
• Press the Mode Selection Pushbutton once (the Mode icons will light up), then press the Port Selection Pushbutton that corresponds to that computer (all three port icons will light up)

Mouse Switching
For mouse port selection: Double-click the scroll wheel of your USB mouse to cycle through the ports.
Notes:
Mouse switching is only supported by USB 3-key scroll wheel mice. Mouse switching is disabled by default (see Hotkey Setting Mode to enable mouse switching). Mouse switching is only supported when Mouse Emulation is enabled.

Hotkey Switching
All hotkey port switches begin with tapping the [Scroll Lock] key twice. The table below describes the actions that each combination performs.
Note: If using the [Scroll Lock] key conflicts with other programs running on the computer, the [Ctrl] key can be used instead.

from the port that currently has the KVM focus to the next port on the switch.

(1 to 2, 2 to 1 for the 2-port

B006-HD2UA2; 1 to 2, 2 to 3,

3 to 4, 4 to 1 for the 4-port B006-HD2UA4).

[Scroll Lock] [Scroll Lock] [n] [Enter]| Brings the KVM, USB hub and audio focus to the computer attached to the port corresponding to the specified Port ID.

Note: [n] represents the computer’s Port ID number (B006-HD2UA2: 1 or 2; B006-HD2UA4: 1, 2, 3 or 4)

.Hotkey Setting Mode (HSM)
Hotkey Setting Mode is used to set functions on the switch. Follow the steps below to invoke HSM and perform a hotkey function.

1.  Press and hold down the [Num Lock] key.
2. Press and release the [-] key.
3.  Release the [Num Lock] key.
4. 5. Warranty & Product RegistrationWarranty & Product RegistrationPress the hotkey to perform the desired function. Refer to the table below for the function.
      Key| Function
      ---|---
      [H]| Toggles between the default ([Num Lock] [-]) and alternate ([Ctrl] [F12]) HSM invocation keys.
      [T]| Toggles between the default ([Scroll Lock] [Scroll Lock]) and alternate ([Ctrl] [Ctrl]) Port Switching keys.
      [F4]| Prints the switch’s current settings via a text editor or word processor.
      [R] [Enter]| Resets the hotkey settings to their default status.
      Key| Function
      ---|---
      [U] [P] [G] [R] [A] [D] [E] [Enter]| Invokes Firmware Upgrade Mode.
      [E]| Enables/disables Power on Detection.
      [N]| Enables/disables keyboard emulation.
      [M]| Enables/disables mouse emulation.
      [W]| Enables/disables Mouse Switching.

Warranty & Product Registration

3-Year Limited Warranty
TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of three (3) years from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment which has been damaged by accident, negligence or misapplication or has been altered or modified in any way.

EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.

Warranty & Product Registration

PRODUCT REGISTRATION
Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*  No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)
• Send the new equipment back for recycling when this ultimately becomes waste

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Photos and illustrations may differ slightly from actual products.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>