CANTON Smart Sound 100 Instruction Manual

CANTON Smart Sound 100 Instruction Manual

www.canton.de/manual/sounddeck100

Thanks!
Thank you very much for choosing this Canton product. You can now look forward to countless hours filled with excellent sound.
Just a few steps and the music can start:

IMPORTANT SAFETY INSTRUCTIONS

Read and follow all instructions. Keep these instructions. Observe all warnings and safety instructions. Operate this device only in a moderate climate (not in a tropical climate). Do not operate this device at altitudes above 2000 m above sea level. To avoid the risk of fire or electric shock, the device must not be exposed to rain or moisture. Do not operate this device near water. Do not expose this device to dripping or splashing water. Strong temperature fluctuations lead to condensation (water droplets) in the device. Wait until the moisture has evaporated (at least three hours). Do not place objects filled with liquids (such as vases) on the device. Do not place open fire, such as lit candles, on or near the device. Do not place the device near heat sources such as radiators, heat accumulators, stoves or other devices (including amplifiers) that generate heat. Avoid direct sunlight. Keep a clearance of at least 5 cm around the device. Never prevent the protective function of polarised or grounded plugs: A polarised plug has two pins, one wider than the other. An earthed plug has a third earthing pin. The wide or third pin is for your safety. If the plug does not fit into your outlet, contact a qualified electrician to replace the obsolete outlet. To avoid electric shock, connect the mains plug only to sockets or extensions where the contact pins can be fully inserted to prevent exposed contact pins. Never touch the signal and mains cable with wet hands. Do not step on or pinch the mains cable, especially not in the area of the plugs, sockets or where the cable is led out of the device. For devices without a mains switch, in which the mains plug or the device mains socket serves as an isolating device, the plug of the mains cable or the device mains socket must be freely accessible at all times. Disconnect the device from the mains during thunderstorms or prolonged periods of non-use. To completely disconnect the device from the power supply, unplug the mains cable from the wall outlet. Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. Always switch off the device before connecting or disconnecting connection cables. Always pull the plugs and not the cables. Install the device according to the manufacturer`s instructions. Always choose a level surface. The device must be in a vertical position. Do not exert force on operating elements, connections and lines. The device may only be operated with the voltage and frequency specified on the device or the type plate. Do not insert any objects or body parts into the openings of the device. Live parts inside the housing could be touched and/or damaged. This can lead to short circuits, electric shocks and fire. Only use fixing materials and accessories that are approved by the manufacturer and/or supplied with the device. Only use trolleys, stands, tripods, holders or tables specified by the manufacturer or sold with the device.

When using a trolley, be careful when moving the trolley/device assembly to prevent damage and injury from tipping over.

Only clean this device with a clean, dry cloth. Do not use any aggressive, alcoholic or abrasive agents for cleaning. To avoid electric shock, do not open the housing! There are no user-serviceable parts in the device. Consult qualified personnel for all repair and maintenance work. This is required when the device has been damaged in any way, such as mains cable or plug damage, liquid or objects have been spilled, exposed to rain or moisture, does not operate normally, or has been dropped. Do not make any changes to the device or accessories. Unauthorised modifications can compromise safety, regulatory compliance or system performance. In this case, the type approval/guarantee may expire.

If sound distortions such as unnatural knocking, throbbing or high frequency clicking occur during playback, the volume level must be reduced immediately.

To avoid possible hearing damage, do not listen at high levels for long periods of time. Interrupt the playback if you hear ringing or whistling noises in your ears or if you have the impression that you can no longer hear high sounds (even for a short time).

New and used batteries must be kept away from children. Devices in which the battery compartment cannot be closed securely must not be used any longer and must be kept away from children. The remote control supplied with this device contains a button cell as battery. Swallowing the button cell can cause serious internal burns and thus death in only 2 hours! Do not ingest the battery, Chemical Burn Hazard. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Take care of your environment when disposing of the battery. Batteries must be disposed of at a battery collection point. Do not expose batteries to high temperatures, such as direct sunlight, fire or the like. Batteries must be inserted correctly according to the polarity imprint. Incorrect insertion can lead to damage. Only use the batteries or rechargeable batteries specified for the device. The batteries supplied are not rechargeable batteries, that means these batteries must not be recharged.

PACKAGING CONTENT

Carefully unpack the Sounddeck 100 and check that the delivery content is complete and undamaged. If any part is damaged, do not use it, but contact our service department (see back cover). Please keep the packaging during the warranty period.

Delivery content:

1x Smart Sounddeck 100
1x Smart-remote
1x Power cord
1x HDMI cable (3m)
1x Optical digital audio cable (1,5m)
1x Coaxial digital audio cable (1,5m)
1x Analog stereo audio cable (1,5m)
1x Short manual

SETUP

Place the Sounddeck 100 in the desired location and connect it to the power outlet using the power cord. To connect the Sounddeck 100 to your TV or other devices, please make sure that they are connected to the mains supply. If you want to connect your Sounddeck 100 to your WiFi network, make sure your WiFi router is active and has access to the internet.

CONNECTION TERMINAL (Back side)

1. HDMI OUT / ARC / [TV] (Supports eARC, 4k, 3D, HDR, HDCP 2.2, CEC) For the connection to the HDMI® (eARC / ARC) input on your TV.
2. HDMI 1-3 / HD1/[BDP], HD2/[SAT], HD3/[PS] (Supports 4k, 3D, HDR, HDCP 2.2, CEC) For the connection to the HDMI® output on your digital devices.
3. OPTICAL / OPT / [CD] For the connection to the optical audio output on your TV or digital device (TOSLINK, max. 24Bit/96kHz).
4. SERVICE For service purposes, only! No charging function, no audio playback!
5. ETHERNET / LAN / [NET] For the connection to the Internet via network cable (RJ45, 8-pin).
6. SUB OUT To connect an optional external subwoofer (RCA, max. 2Vrms).
7. COAXIAL / COX / [DVD] For the connection to the digital coaxial audio output on your TV or digital device (RCA, max. 24Bit/96kHz).
8. AUX LEFT+RIGHT / LIN / [AUX] For the stereo connection to the analog line output on your playback device (RCA, max. 2Vrms).
9. POWER INPUT For the connection to the mains (IEC C8).

SMART-REMOTE

DISPLAY INDICATIONS

The Sounddeck 100 has an On-screen display (menu visible on the TV), a LED status indicator (green or red) and a LED display (in the front of the Sounddeck 100).

On-Screen display
All settings and the configuration of the Sounddeck 100 can be conveniently performed via the On-screen display on your TV screen. To do this, the Sounddeck 100 must be connected to your TV via a HDMI® cable. The menu is simple and structured and all changes you make on the Sounddeck 100 are displayed on your TV. By pressing the menu button (M) on the Smart-remote, you can access the main menu.

Practical tip:

• To change the language of the On-screen display from German to English, please go to the main menu by pressing the button ,,M”. Under ,,Systemeinstellung” [SYS] select the menu item ,,Displayeinstellungen” [UIS] and change the language under the menu item ,,Spruce” [LAN].

LED status indicator
When you switch on the Sounddeck 100, the Status LED lights up green. In standby mode, the Status LED lights up red.

LED display
The LED display is located in the front of the Sounddeck 100 and lights up for five seconds when a command is sent. It indicates the selected function as abbreviation or scroll text. The most important display indications and their meanings are listed here:

Note:

• Further displays can be found in the detailed operating instructions. These can be found at: www.canton.de/manual/sounddeck100

CONNECTION TO TV DEVICE

HDMI® (recommended)

1. Connect a HDMI® cable from the HDMI OUT (ARC) output on the back of the Sounddeck 100 to the HDMI IN (eARC/ARC) input on your TV.
2. Now select the input [TV] by the Smart-remote using the up or down arrow key ( ).

Notes:

• A HDMI® connection supports digital audio and video with a single cable. It is the best option to connect your Sounddeck 100.
• If your TV features a HDMI® ARC/eARC connector, you can enjoy also the TV internal audio through your Sounddeck 100 by using this HDMI® cable.
• This HDMI® connection is required if you intend to connect other video devices to the Sounddeck 100 inputs to display on your TV.
• In this case, activate CEC mode on your TV. CEC (Consumer Electronics Control) is a feature that allows compatible devices to be controlled from a single remote control. For details, refer to the instruction manual of your TV.

Optical digital input (alternative)

1. Connect the input OPTICAL on the Sounddeck 100 to the OPTICAL OUT connector of your TV with an optical cable.
2. On the Smart-remote, use the up and down arrows ( ) to select the input [CD].

Note:

• Make sure you have removed the protective caps from both ends of the optical cable.

CONNECTION TO OTHER DEVICES

HDMI® (recommended)
To connect other digital devices such as a satellite receiver, BluRay-player, game console, etc. it is recommended to connect them via one of the 3 HDMI® inputs of the Sounddeck 100.

1. Connect one of the 3 HDMI® inputs (HD1/HD2/HD3) on the back of the Sounddeck 100 with the HDMI OUT output on your digital device with a HDMI® cable.
2. Now, select the used input [BDP] for HD1, [SAT] for HD2 or [PS] for HD3 with the up or down arrow key ( / ) on the Smart-remote.

Note:

• Make sure that you do not connect the other playback devices to the TV, but directly to the Sounddeck 100. This is the only way to ensure that the best possible multichannel audio format / audio signal is reproduced.

Optical digital input (alternative)

1. Connect the input OPTICAL at the Sounddeck 100 to the OPTICAL OUT connector of your TV with an optical cable.
2. On the Smart-remote, use the up and down arrows ( ) to select the input [CD].

Notes:

• If the optical digital input is already in use, please use one of the other unused inputs (COAXIAL and/or AUX).
• Make sure you have removed the protective caps from both ends of the optical cable.

USING CHROMECAST BUILT-INTM

Notes: · On your (mobile) device the WiFi and Bluetooth® function must be switched on. Make sure that your (mobile) device is already connected to the WLAN (WiFi network). · You will need an app that supports playback via Chromecast built-in (e.g. Spotify, Deezer, All Cast, Tune In, etc.). Audio playback with the Google Home app directly is not possible.

Download the Google Home app
To use the integrated Chromecast built-in function, you need to install the Google Home app on your (mobile) device. Open the app ,,Play Store” / ,,App Store” on your (mobile) device. Search for the Google Home app and install it on your (mobile) device. You need to confirm access to several functions, such as identity, etc. Please start the Google Home app and follow the instructions. You`ll need to assign a Google Account to the app (create a new Google Account if necessary) to complete the sign-in process.

Setting up Sounddeck 100 using the Google Home app

1. Open the Google Home app on your (mobile) device.
2. Your (mobile) device is now searching for available speakers within range. If necessary, you may have to select the search function manually. The Sounddeck 100 will be available only after [NET] followed by [SET] has been indicated (once) in the speaker display.
3. Select Sounddeck100xxx as the device to set up.
4. Now, your (mobile) device is trying to connect to Sounddeck 100 using Bluetooth® wireless technology. Please follow the installation steps of the Google Home app.
5. After the connection has been established, the Sounddeck 100 plays a melody (sound sequence). Please confirm that you have heard the melody.
6. Now select the ,,room” in which you want to use the Sounddeck 100 (e.g. living room) and confirm with ,,Next”.
7. Please select the WiFi network (WLAN) you want to use for the Sounddeck 100 and click ,,Next”.
8. The selected WiFi network and the Sounddeck 100 are now connected. After a successful connection the display of the Sounddeck 100 shows [WIF] followed by [CON].
9. Now the installation is almost finished. Please follow a few final steps on your (mobile) device to complete the installation.

Google Assistant Voice control
You can operate the Sounddeck 100 in two ways with the ,,Google Assistant” voice control:

1. Connecting to a separate Google Home device.
2. Using the Google Home app-integrated voice control.

Further information can be found under: assistant.google.com

Note:

• Google Assistant is not available in certain languages and countries.

PLAYBACK VIA SPOTIFY CONNECT

Use your phone, tablet, or computer as a remote control for Spotify. Go to spotify.com/connect to learn how.

CONNECTION VIA BLUETOOTH® WIRELESS TECHNOLOGY

You can conveniently connect the Sounddeck 100 to your (mobile) device via Bluetooth® wireless technology. For this, please proceed as follows:

Establish connection via Bluetooth® wireless technology

1. Select the Bluetooth® input [BT] by repeatedly pressing the arrow keys ( ) on the Smart-remote.

2. Now, press the button ,,Bluetooth Pairing” on the Smart-remote. The dis- play indicates [BTP].

3. Start the search on your (mobile) device.

4. Select Sounddeck 100 as the playback device.
   Note:
   • If you have assigned a name to the Sounddeck 100 during network setup (e.g. living room), this name is also displayed here.

5. After confirmation, the connection is established automatically and the message [BT-] and [CON] appears on the display of the Sounddeck 100.

6. Start playback of a track on your (mobile) device and the sound is automatically played back via the Sounddeck 100.

7. If the connection has failed, you receive the message [FAI].

8. If the (mobile) device requires a code, enter 0000.

9. If [BT-] and [DIS] appears on the display, your (mobile) device is out of range or logged out.

USING AirPlay 2 TECHNOLOGY

With Apple AirPlay technology, you can play audio content over the wireless network (WLAN) using your Smart Sounddeck 100. Additionally, AirPlay 2 technology offers you the possibility to play your content on several loudspeakers and/or amplifiers synchronously.

Connecting the Smart Sounddeck 100 to the WLAN (WiFi network) via iPhone, iPad or iPod touch

To connect your Smart Sounddeck 100 to your wireless network (WLAN) via iPhone, iPad or iPod touch, please proceed as follows:

1. Connect your Sounddeck 100 to the power outlet and wait until the display shows [NET] and [SET].

2. On your iPhone, iPad or iPod touch, select ,,Settings” and then ,,Wi-Fi” (WLAN).

3. Under the menu item ,,SET UP NEW AIRPLAY SPEAKER” select the Smart Sounddeck 100 as the device to be installed.

4. The ,,AirPlay Config…” window opens.
   a. Under ,,Network” select the network to which you want to connect the Smart Sounddeck 100.
   b. Under “Speaker name” enter the name (synonym) you want to assign to the Sounddeck 100.
   c. Optionally, you can assign a password under ,,SPEAKER PASSWORD”.
   d. Select the function ,,Next” and wait (approx. 30 seconds) until the Sounddeck 100 shows [WIF] / [CON] in the display.

5. Finalize the registration process in the ,,Configuration finished” window that opens by pressing the ,,Done” button. The Smart Sounddeck 100 is now connected to your WLAN (WiFi network) and ready for use.

Playback via AirPlay resp. AirPlay 2 Technology
Requirements to play music using AirPlay 2 technology:

• iPhone, iPad, iPod touch or Home Pod with iOS 11.4 or higher.
• Apple TV 4k or Apple TV HD with tVOC 11.4 or higher
• Mac or PC with iTunes 12.8 or higher resp. Mac with macOS Catalina or
  higher.

Playback on Smart Sounddeck 100 (and other devices):

1. To play your music using the Sounddeck 100, start the playback of the desired title in a media app on your [mobile] device.
2. Open the Control Center on your Apple device. Swipe from the top right corner (iOS 12 or higher) or from the bottom (iOS 11 or lower) towards the center of the display.
3. Select the AirPlay symbol in the Audio Card, and in the dialog that opens select the speaker(s) resp. amplifier(s) which you want to use for playback.

To start music playback on one or more AirPlay-enabled speaker(s) via Mac, Apple TV or Apple Music, please refer to the following support page: https://support.apple.com/en-ca/HT202809

Notes:

• Use Siri on your iPhone, iPad, Home Pod, or Apple TV to control the Sounddeck 100 with just your voice.
• The Smart Sounddeck 100 supports only audio streaming, no video streaming.

ASSIGNING PRESET 1-3

The Sounddeck 100 is able to assign three memory buttons with ,,presents”. Settings like volume, selected input and settings in the Speaker Setup [SPS] menu (sound settings, etc.) as well as playlists from the app ,,Spotify” can be stored.

Practical tip:

• We recommend you to store the settings you have made in the loudspeaker menu during the initial set-up of the Sounddeck 100, e.g. regarding loudspeaker levels and distances, sound settings, etc., to one of the preset buttons so that your settings are not overwritten by the (neutral) factory settings if you accidentally press one of these three preset buttons.

To store playlists and/or (sound)settings, please proceed as follows:

1. Please apply the desired settings regarding volume, sound, input, etc. and press and hold the memory button 1, 2 or 3 until the corresponding number [P1], [P2] or [P3] is shown in the display and no longer flashes.
2. To store a playlist, please open the desired playlist on the app ,,Spotify” on your (mobile) device and start playback. Be sure to select Spotify Connect as your connection to the Sounddeck 100, not Chromecast built-in. Now, press and hold the corresponding memory button 1, 2 or 3 until the corresponding number [P1], [P2] or [P3] is shown in the display and no longer flashes. Storing a playlist automatically stores all (sound)settings, too.
3. To recall the settings resp. a playlist from these presents, please press the corresponding button 1, 2 or 3 briefly. The settings are then called up, resp. the tracks from the stored playlist are played back automatically by the Sounddeck 100 (even without using your (mobile) device).

Note:

• To delete the settings or a playlist from a preset button, please press and hold the relating button for 10 seconds until the corresponding preset [P1], [P2] or [P3] is shown in the display rapidly flashing.

PAIRING WIRELESS SPEAKERS

The Sounddeck 100 offers you the possibility to pair up to 7 Canton Smart Speakers wirelessly to an up to 5.1.2 home theatre system.

Attention:

• Before pairing a Canton Smart Speaker to Smart Sounddeck 100, please make sure that the Smart Speaker to be (newly) paired has been disconnected from the power supply for minimum 30 seconds.

Pairing Smart Speakers wirelessly:

1. Enter the main menu by pressing the ,,M” button. Select the menu item ,,Wireless Setup” [WIS] using the up or down arrow ( ) and press ,,OK”.
2. Confirm the first item ,,Wireless Speaker Pairing” [WSP] with the ,,OK” button. Now, select the speaker to be connected (paired) using the up or down arrow ( ) and confirm your selection with the ,,OK” button.
3. After ,,Pairing” is shown on the TV screen and [PIR] is indicated on the speaker display, plug the power cord of the (new) speaker to be connected into the power outlet and/or turn on the power switch (if present). After a successful pairing process the On-screen display shows ,,Connected” and the display of the Sounddeck 100 as well as the display of the slave speaker indicates [CON].

Note:

• In a home theatre setup, the Sounddeck 100 is always the ,,master speaker”, all other speakers are defined as ,,slave speakers”. and controlled by the Sounddeck 100.

AUTOMATIC UPDATES

After you have connected the Sounddeck 100 to the network, firmware updates are executed automatically. After each connection to the power supply and at regular intervals (also in standby mode), the Sounddeck 100 searches for an update and installs it, if available. The LED flashes green/red during the update and the display first shows ,,DOWNLOADING”, then ,,UPDATING”. During this time the Sounddeck 100 is not operable. To do this, the Sounddeck 100 must have been connected to the network router via the Google Home app or an iOS device (by use of WLAN) or alternatively by a network cable (by use of LAN).

Caution:

• Do NOT disconnect the Smart Sounddeck 100 from the power supply during an update process!

FURTHER FUNCTIONS AND NOTES

The Sounddeck 100 contains a multitude of other great functions. All settings can be found in the detailed instruction manual. This can be found under: www.canton.de/manual/sounddeck100

TECHNICAL DATA

Power supply

• Operating voltage 100–240V~
• Operating frequency 50/60Hz
• Power consumption ECO Standby 0.40W
• Power consumption NSB Standby WLAN [WIF] ca. 1.9W (Factory setting)
• Power consumption NSB Standby LAN [ETH] ca. 6.6W
• Power consumption AUT Standby ca. 6.6W
• Power consumption MAN Standby ca. 4.2W
• Power consumption in idle mode (no output signal) ca. 9.8W
• Power consumption maximal ca. 150W

Bluetooth® Wireless Technology

• Bluetooth® standard 4.1 (A2DP)
• Distance Up to 10m
• Max. transmission power 100mW (+20dBm)
• Frequency range 2402–2480MHz (ISM band)
• Antenna gain 4.2dBi

Dimensions:
W: 100cm
H: 7cm
D: 33cm

Weight:
12,3kg

WLAN

• Max. transmission power 100mW (+20dBm)

• Frequency range 2412-2472MHz (802.11b/g/n)
  5150-5350MHz and 5470-5725MHz (802.11a/n/ac)

• Antenna gain 4.2dBi @ 2.4GHz, 4.5dBi @ 5GHz

Wireless Audio

• Max. transmission power 100mW (+20dBm)

• Frequency range 2402-2480 MHz (2412MHz, 2438MHz and 2464MHz)
  5180-5240 MHz (5180MHz, 5210MHz and 5240MHz)
  5736-5814 MHz (5736MHz, 5762MHz and 5814MHz)

• Antenna gain 4.2dBi @ 2.4GHz, 4.5dBi @ 5GHz

Decoder

• Dolby Atmos®
• DTS-HD®
• PCM (32kHz-96kHz, 8Bit-24Bit)

Ambient temperature

• Minimum 5°C (41°F)
• Maximum 35°C (95°F)

FURTHER IMPORTANT INFORMATION

Information on “Intended Use”
The speaker system is designed for indoor use and must not be used outdoors or in a wet environment. Do not make any conversions or modifications to the device. Connect the speaker system as described in the instructions and observe the safety instructions. Only operate the device with the mains voltage and frequency specified on the rating plate.

Information about an environmentally friendly operation
To reduce the power consumption, switch the speaker system to standby mode by pressing the Power ,, ” button when not in use. This “saves power” and lowers your electricity bill.

Information about the CE marking
Electrical and electronic devices placed on the market within the European Union must be given a CE mark to indicate that the equipment complies with the applicable requirements (e.g. equipment safety or electromagnetic compatibility).

Disposal instructions
According to the EU Directive on Waste Electrical and Electronic Equipment, devices marked with this symbol must not be disposed of together with municipal waste (household waste). Please inform yourself, if necessary, contact your local disposal company or the municipal/city administration about the free disposal for you. It serves the environmental and health protection as well as the saving of (rare) raw materials by recycling.

Batteries must also not be disposed of together with general household waste. They must be collected separately and returned to a battery collection point. Throw empty batteries into the collection container free of charge, for example, those situated at the trade. Improperly disposed of batteries can harm human and animal health and/or the environment.

EU – Declaration of Conformity

labelling
We, the manufacturer / importer Canton Elektronik GmbH + Co. KG · Neugasse 21-23 · 61276 Weilrod · Germany

confirm and declare in sole responsibility that the product
Smart Sounddeck 100
(Dolby Atmos® enabled sounddeck with several signal in- and outputs, WiFi and Ethernet connections, Bluetooth® wireless technology, internal switch mode power supply and infrared remote control) is in accordance with the Directives of the European Parliament and of the Council
Directive 2014/53/EU (Radio Equipment)
Directive 2014/35/EU (Low Voltage Directive)
Directive 2011/65/EU (Restriction of the Use of Certain Hazardous Substances)
Directive 2012/19/EU (Waste of Electric and Electronic Equipment)
Directive 2009/125/EG (Ecodesign requirements for Energy-related Products)
Operation is permitted in all countries of the European Union. A complete Declaration of Conformity can be found at: www.canton.de/en/doc
Legally binding signature:
Date: 01st April 2021 Name: Günther Seitz Function: Managing Director 44

LICENSE INFORMATION

http://www.spotify.com/connect/third-party-licenses

http://patents.dts.com.

WARRANTY

Above and beyond the legal warranty period Canton offers a warranty of 5 years on all its passive loudspeakers. A 2-year warranty is offered for active and semi-active speakers and devices. The warranty period begins at the time of purchase and only applies to the purchaser. Warranty claims will only be accepted if accompanied by the original packaging. The warranty does not cover damages incurred in transit or damages caused by improper use. The warranty is not extended if parts are exchanged within the period covered by the warranty. This applies to all loudspeakers purchased from an authorised Canton dealer. In the event of damage please contact your dealer or the Canton Service department direct.

For further questions, please do not hesitate to contact our Customer
Service:

Canton Elektronik GmbH + Co. KG
Neugasse 21 – 23
61276 Weilrod, Germany
Tel. +49 (0)6083 287-87
info@canton.de
www.canton.de

All Statements without guarantee.
Technical changes, typing errors and other errors reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>