TESLA WF81492M Washing Machine User Manual
- June 6, 2024
- Tesla
Table of Contents
WASHING MACHINE
WF81492M User Manual
SAFETY INSTRUCTIONS
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury or loss of life. Explanation of the symbols:
WARNING!
This combination of symbol and signal words indicates a potentially dangerous
situation that may result in death or serious injuries unless it’s avoided.
CAUTION!
This combination of symbols and signal words indicates a potentially dangerous
situation that may result in slight or minor injuries or damage to property
and the environment. NOTE
This combination of symbols and signal words indicates a potentially dangerous
situation that may result in slight or minor injuries.
WARNING!
The electric shock!
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
- The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.
- Before any maintenance of the device, unplug the appliance from the mains.
- Always unplug the machine and turn off the water supply after use. The max. inlet water pressure, in pascals. The min. inlet water pressure, in pascals.
- To ensure your safety, a power plug must be inserted into an earthed three-pole socket. Check carefully and make sure that your socket is properly and reliably earthed.
- Make sure that the water and electrical devices must be connected by a qualified technician in accordance with the manufacturer’s instructions and local safety regulations.
- Pull out its plug from the power socket before cleaning or maintenance.
- Do not use any socket with a rated current less than that of the appliance. Never pull out the power plug with a wet hand.
- Please remember to disconnect the water and power supply immediately after the clothes are washed.
Risk to children!
- EN countries: the appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Children of less than 3years should be supervised to ensure that they do not play with appliances.
- Animals and children may climb into the machine. Check the machine before every operation.
- Kids should be supervised that they do not play with the appliance.
- Glassdoor may be very hot during the operation. Keep kids and pets far away from the machine during the operation in very wet rooms as well as in the rooms with explosive or caustic gas.
- Remove all packages and transport bolts before using the appliance. Otherwise, serious damage may result.
Risk of explosion!
- Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances( such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.)This may result in fire or explosion.
- The washer-dryer is not to be used if industrial chemicals have been used for cleaning.
- The exhaust air must not be discharged into a flue which is for exhausting fumes from appliances burning gas or other fuels.
- Beforehand thoroughly rinse items of washing by hand.
CAUTION!
Installing the product!
- This washing machine is for indoor use only.
- It isn’t intended to be built-in using.
- The openings must not be obstructed by a carpet.
- Washing machines shall not be installed in bathrooms or very wet rooms as well as in rooms with explosive or caustic gases.
- The washing machine with a single inlet valve only can be connected to the cold water supply. The product with double inlet valves should be correctly connected to the hot water and cold water supply.
- The plug must be accessible after installation.
- The appliance must not be installed behind a lockable door, a sliding door, or a door with a hinge on the opposite side to that of the washer dryer.
- The appliance shall not be installed in a humid place.
- Remove all packages and transport bolts before using the appliance. Otherwise, serious damage may result.
Risk of damaging appliance!
-
Your product is only for home use and is only designed for textiles suitable for machine washing.
-
Do not climb up and sit on the top cover of the machine.
-
Do not lean against the machine door.
-
Cautions during Handling Machine:
1. Transport bolts shall be reinstalled to the machine by a specialized person.
2. The accumulated water shall be drained out of the machine.
3. Handle the machine carefully. Never hold each protruded part on the machine while lifting. Machine door can not be used as the handle during the conveyance.
4. This appliance is heavy. Transport with care.
5. That the hands shall not be inserted into running water-extracting tub. -
Please do not close the door with excessive force. If it is found difficult to close the door, please check if the clothes are put in or distributed well.
-
It is forbidden to wash carpets.
Operating the appliance!
- Before using the washing machine, the product shall be calibrated.
- Before washing the clothes for the first time, the product shall be operated in one round of the whole procedure without the clothes inside.
- Flammable and explosive or toxic solvents are forbidden. Gasoline and alcohol etc. Shall not be used as detergents. Please only select the detergents suitable for machine washing, especially for drums.
- Make sure that all pockets are emptied. Sharp and rigid items such as coins, brooch, nails, screws or stones, etc. may cause serious damage to this machine.
- Please check whether the water inside the drum has been drained before opening its door. Please do not open the door if there is any water visible.
- Be careful of burning when the product drains hot washing water.
- After the program is completed, please wait for two minutes to open the door.
- Never refill the water by hand during washing.
- If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products. it is placed in a tumble dryer they should first be washed in hot water with extra detergent, this will reduce, but not eliminate, the hazard.
- Adequate ventilation has to be provided to avoid the backflow of gases into the room from appliances burning other fuels, including open fires.
- Do not dry unwashed items in the appliance.
- Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes, and wax removers should be washed in hot with an extra amount of detergent before being dried in the appliance.
- Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber-backed articles, and clothes or pillows fitted with foam rubber pads should not be dried in the machine.
- Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.
- The machine whose lid can be opened during water extraction, that it takes 15s or more for a complete stop of the water-extracting chamber tub.
- The final part of a washer-dryer cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged.
- Remove all objects from pockets such as lighters and matches before using the appliance.
- WARNING: Never stop a washer dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
Packaging/Old appliance
This marking indicates that this product should not be disposed of with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the collection systems or contact the retailer
where the product was purchased. They return and can take this product for
environmentally safe recycling.
INSTALLATION
Product Description
NOTE
- The product line chart is for reference only, please refer to real product as standard.
Transport hole plug| Supply hose
cold water| Supply hose hot
water (optional)| Drain hose support
(optional)| Owner’s manual
Installation area
WARNING!
- Stability is important to prevent the product from wandering!
- Make sure that the product should not stand on the power cord.
Before installing the machine, the location characterized as follows shall be selected:
- Rigid, dry, and level surface
- Avoid direct sunlight
- Sufficient ventilation
- Room temperature is above 0 °C
- Keep far away from the heat resources such as coal or gas.
Unpacking the washing machine
WARNING!
- Packaging material (e.g. Films, Styrofoam) can be dangerous for children.
- There is a risk of suffocation! Keep all packaging well away from children.
- Remove the cardboard box and styrofoam packing.
- Lift the washing machine and remove the base packing. Make sure the small triangle foam is removed with the bottom one together. If not, lay the unit down with side surface, then remove the small foam from the unit bottom manually.
- Remove the tape securing the power supply cord and drain hose.
- Remove the inlet hose from the drum.
Remove transport bolts
WARNING!
- You must remove the transport bolts from the backside before using the product.
- You’ll need the transport bolts again if you move the product, so make sure you keep them in a safe place.
Please take the following steps to remove the bolts:
- Loosen 4 bolts with a spanner and then remove them.
- Stop the holes with transport hole plugs.
- Keep the transport bolts properly for future use.
Leveling the washing machine
WARNING!
- The lock nuts on all four feet must be screwed tightly against the housing.
- Check if the legs are closely attached to the cabinet. If not, please turn them to their original positions tighten the nuts.
- Loosen the lock nut turn the feet until it closely contacts with the floor.
- Adjust the legs and lock them with a spanner, making sure the machine is steady.
Connect Water Supply Hose
WARNING!
- To prevent leakage or water damage, follow the instructions in this chapter!
- Do not kink, crush, modify or sever water inlet hose.
- For the model equips hot valve, connect it to a hot water tap with a hot water supply hose. Energy consumption will decrease automatically for some programs.
Connect the inlet pipe as indicated, There are two ways to connect the inlet pipe.
-
The connection between ordinary tap and inlet hose.
Loosen clamp nut and
four bolts| Tighten clamp nut| Press slide bushing insert inlet
hose into connecting base| Tighten clamp nut
2. The connection between screw tap and inlet hose.
Connect the other end of the inlet pipe to the inlet valve at the backside of the product and fasten the pipe tightly clockwise.
Drain Hose
WARNING!
- Do not kink or protract the drain hose.
- Position drain hose properly, otherwise damage might result from water leakage. There are two ways to place the end of the drain hose:
NOTE
- If the machine has drain hose support, please install it like the following.
WARNING!
- When installing a drain hose, fix it properly with a rope.
- If the drain hose is too long, do not force it into the washing machine as it will cause abnormal noises.
OPERATIONS
Quick Start
CAUTION!
- Before washing, please make sure it’s installed properly.
- Before washing for the first time, the washing machine shall be operated in one round of the whole procedure without clothes in as follows.
CALIBRATION
It’s recommended to calibrate the washing machine so that can serve you
better.
- Empty the washing machine;
- Plugin;
- Power on the washing machine and press “Delay” and “Speed” at the same time within 10 seconds then display “t19”
- Press to start the washing machine and wait till display “****”
1. Before Washing
NOTE
- Detergent needs to be added in “case I“ after selecting pre-washing for machines with this function.
2. Washing
NOTE
- If the default is selected, step 3 can be skipped.
- The function button line chart is for reference only, please refer to the real product as standard.
3. After Washing
Buzzer beep or “End” on display.
Before Each Washing
- The working condition of the washer should be (0-40) °C. If used under 0 °C, the inlet valve and draining system may be damaged. If the machine is placed under a condition of 0 °C or less, then it should be transferred to normal ambient temperature to ensure the water supply hose and drain hose are not frozen before use.
- Please check the labels and the explanation of using detergent before washing. Use non-foaming or less-foaming detergent suitable for machine washing properly.
WARNING!
- When washing single clothes, it may easily cause great eccentricity and give alarm due to great unbalance. Therefore it is suggested to add one or two more clothes to be washed together so that draining can be done smoothly.
- Don’t wash clothes that have been in touch with kerosene, gasoline, alcohol, and other flammable materials.
Detergent Dispenser
Prewash detergent
Main wash detergent
Softener
CAUTION!
- Detergent only needs to be added in “case I“ after selecting prewashing for machines with this function.
Program| | |
---|---|---|---
Cotton| | |
Quick 15’| | |
Rapid 45’| | |
60’ Wash| | |
ECO 40-60| | |
Intensive| | |
Rinse &Spin| | |
Sterilization| | |
Sport Wear| | |
Synthetic| | |
Mix| | |
Delicate| | |
Wool| | |
20°C| | |
Spin Only| | ****|
Means must
Means optional
NOTE
- As for the agglomerated or ropy detergent or additive, before they are poured into the detergent box, it is suggested to use some water for dilution to prevent the inlet of the detergent box from being blocked and overflowing while filling water.
- Please choose the suitable type of detergent for the various washing temperature to get the best washing performance with less water and energy consumption
Control Panel
NOTE
- The chart is for reference only, please refer to the real product as standard.
-
On/Off
The product is switched on or off. -
Start/Pause
Press the button to start or pause the washing cycle. -
Option
This allows you to select an additional function and will light when selected. -
Programs
Available according to the laundry type. -
Display
The display shows the settings, estimated time remaining, options, and status messages for your washer. The display will remain on through the cycle.
Option
Delay
Set the Delay function:
- Select a program
- Press the Delay button to choose the time(the delaying time is 0-24 H.)
- Press [Start/Pause] to commence the delayed operation
Cancel the Delay function:
Press the [Delay] button until the display is 0H. It should be pressed before
starting the program. If the program already started, should press the
[On/Off] button to reset the program.
CAUTION!
If there is any break in the power supply while the machine is operating, the
selected program will be stored in special memory when the power is restarted,
press the [On/Off] button, the program will continue.
Pre Wash
The Prewash function can get an extra wash before main wash, it is suitable
for washing the dust rises to the surface of the clothes; You need to put
detergent into the Case (I) when selecting it.
Extra Rinse
The laundry will undergo an extra rinse once after you select it.
My Cycle
To memory the frequently used program. After choosing the program and setting
the options, press [Speed] 3 sec. before starting to wash. The default setting
course is Cotton.
Other functions
Temp.
Press the button to regulate the temperature (Cold, 20 °C, 30 °C, 40 °C, 60°C,
90 °C)
Speed
Press the button to change the speed. 1400:
0-400-600-800-1000-1200-1400
Program| Default Speed (rpm)
---|---
| 1400
Cotton| 1000
Quick 15’| 800
Rapid 45’| 800
60’ Wash| 1000
ECO 40-60| 1400
Intensive| 800
Rinse &Spin| 1000
Sterilization| 800
Sport Wear| 800
Synthetic| 800
Mix| 1000
Delicate| 800
Wool| 600
20°C| 1000
Spin Only| 1000
Child Lock
To avoid miss-operation by children.
Press [Temp.] and [Speed] 3 sec. till buzzer beep.
CAUTION!
When the child lock is activated and the program starts, the child lock
indicator will switch on, and the CL and the remaining time on the display is
alternately displayed in 0.5s. Pressing the other buttons will make the child
lock indicator flash for 3s. when the program finishes, CL and END alternate
for 10s in 0.5s, then the child lock lights flash for 3s
- Only pressing and holding the two-button can release the child lock, even power off, switch off, and program end
- The “Child Lock” will lock all buttons except the Power button and Child Lock button
- Please release the child lock before selecting the program and staring washing
Mute the buzzer
To act the buzzer function, press the two buttons again for 3 seconds. The setting will be kept until the next reset.
CAUTION! After Muting the buzzer function, the sounds will not be activated anymore.
Programs
Programs are available according to the laundry type
Programs|
---|---
Cotton| Hard-wearing textiles, heat-resistant textiles made of cotton or
linen.
Synthetic| Wash synthetic articles, for example, shirts, coats, blending.
While washing the knitting textiles, the detergent quantity shall be reduced
due to its loose string construction and easily forming bubbles.
Mix| Mixed load consisting of textiles made of cotton and synthetics.
20°C| 20°C default, can choose cold water.
Quick 15′| Extra short program approx, suitable for lightly soiled washing as
a small amount of laundry.
Rapid 45′| This program is suitable for washing not very dirty clothes, saving
more
energy and washing.
60′ Wash
•| This program is suitable for daily wash, for daily laundry, to achieve a
good washing performance of about 60min.
ECO 40-60| Default 40°C, not selectable, suitable for laundry washing at about
40°C -60°C.
Wool| Hand or machine-washable wool or rich wool textiles.Especially gentle
wash program to prevent shrinkage, longer program pauses (textiles rest
in wash liquor).
Spin Only| Extra spin with selectable spin speed.
Intensive| To increase the washing effects, washing time is increased.
Sterilization
I.| Keep the washing temperature above 60 degrees for more than 30 minutes,
effectively removing harmful bacteria.
Delicate| For delicate, washable textiles, e.g. made of silk, satin, synthetic
fibers, or blended fabrics.
Sport Wear| This program is suitable for washing sportswear.
Rinse&Spin| Extra rinse with spin.
Washing Programs Table
Program | Load(kg) | Temp.(°C) | Default Time |
---|---|---|---|
8 | Default | 8 | |
Cotton | 8 | 40 | 3:39 |
Quick 15’ | 2 | Cold | 0:15 |
Rapid 45’ | 2 | 20 | 0:45 |
60’ Wash | 2 | 30 | 1:00 |
ECO 40-60 | 8 | – | 3:32 |
Intensive | 8 | 40 | 3:48 |
Rinse &Spin | 8 | – | 0:20 |
Sterilization | 4 | 70 | 2:27 |
Sport Wear | 4 | 20 | 0:45 |
Synthetic | 4 | 40 | 3:18 |
Mix | 8 | 40 | 1:20 |
Delicate | 2 | 30 | 0:50 |
Wool | 2 | 40 | 1:07 |
20°C | 4 | 20 | 1:01 |
Spin Only | 8 | – | 0:12 |
- Concerning Regulation(EU) No 1061/2010, The EU energy efficiency class is A+++ Energy test program: Intensive 60/40°C; Speed: The highest speed; Other as the default. Half load for 7.0/8.0Kg machine:3.5/4.0Kg.
- Concerning Regulation(EU) 2019/2023, The EU energy efficiency class is B Energy test program: ECO 40-60. Other as the default. Half load for 7.0/8.0Kg achine:3.5/4.0Kg. Quarter load for 7.0/8.0Kg machine:2.0/2.05Kg.
NOTE
The parameters in this table are only for the user’s preference. The actual
parameters may be different from the parameters in the above-mentioned table.
MAINTENANCES
Cleaning And Care
WARNING! Before your maintenance starts, please unplug the machine and close
the tap.
Cleaning The Cabinet
Proper maintenance on the washing machine can extend its working life. The
surface can be cleaned with diluted non-abrasive neutral detergents when
necessary. If there is any water overflow, use the wet cloth to wipe it off
immediately. No sharp items are allowed.
NOTE
Formic acid and its diluted solvents or equivalent are forbidden, such as
alcohol, solvents, or chemical products, etc.
Cleaning The Drum
- The rusts left inside the drum by the metal articles shall be removed immediately with chlorine-free detergents. Never use steel wool.
NOTE Don’t put laundry in the washing machine during the drum cleaning.
Cleaning The Door Seal and Glass
Wipe the glass and seal after each wash to remove lint and stains. If lint
builds up it can cause leaks. Remove any coins, buttons, and other objects
from the seal after each wash.
Cleaning The Inlet Filter
NOTE
- Inlet filter must be cleaned if the water pressure is low.
Washing the filter in the tap
- Close the tap.
- Remove the water supply hose from the tap.
- Clean the filter.
- Reconnect the water supply hose.
Washing the filter in washer dryer:
- Screw off the inlet pipe from the backside of the machine.
- Pull out the filter with long nose pliers and reinstall it back after being a wash
- Use the brush to clean the filter.
- Reconnect the inlet pipe.
NOTE
- If the brush is not clean, you can pull out the filter and wash it separately;
- Reconnect, turn on the tap.
Cleaning The Detergent Dispenser
- Press down the arrow located on the softener cover inside the dispenser drawer.
- Lift the clip up and take out the softener cover and wash all grooves with water.
- Restore the softener cover and push the drawer into position.
Pull out the dispenser drawer by pressing the button marked with “A“| Clean the dispenser drawer underwater| Clean inside the recess with an old toothbrush| Insert the dispenser drawer
NOTE
- Do not use alcohol, solvents or chemical products to clean the machine.
Cleaning The Drain Pump Filter
WARNING!
- Be careful of the hot water!
- Allow the detergent solution to cool down.
- Unplug the machine to avoid electrical shock before washing.
- A drain pump filter can filter the yarns and small foreign matters from the washing.
- Clean the filter periodically to ensure the normal operation of the washing machine.
CAUTION!
- Make sure that valve cap and emergency drain hose are reinstalled properly, cap plates should be inserted aligning to hole plates otherwise water may leak;
- Some machines don’t have an emergency drain hose, rotate the lower cover cap directly to make water run into the basin.
- When the appliance is in use and depending on the program selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the cover, ensure it is securely re-tightened.
TROUBLESHOOTING
Description | Reason | Solution |
---|---|---|
The washing machine cannot startup | The door is not closed properly | Restart |
after the door is closed Check if the clothes are stuck
The door can’t be opened| The washer’s safety protection design is working|
Disconnect the power, restart the product
Description| Reason| Solution
---|---|---
Water leakage| The connection between inlet pipe or outlet hose is
not tighten| Check and fasten water pipes Clean up outlet hose
Detergent residues in the box| Detergent is dampened or agglomerated| Clean
and wipe the detergent box
Indicator or display does not light| Disconnect the power PC board or harness
has
connection problem| Check if the power is shut down and the
the power plug is connected correctly
Abnormal noise| | Check if the fixing (bolts) have been removed Check it’s
installed on a solid and level floor
Description| Reason| Solution
---|---|---
| The door is not closed properly| Restart after the door is closed Check if
the clothes is stuck
| Water injecting problem while washing| Check if the water pressure is too
low
Straighten the water pipe Check if the inlet valve filter is blocked
| Overtime water draining| Check if the drain hose is blocked
| Water overflow| Restart the washer
| Others| Please try again first, call up service line if there are still
troubles
NOTE
- After the check, activate the appliance. If the problem occurs or the display shows other alarm codes
again, contact the service.
Technical Specifications
MAX. Current | 10A |
---|---|
Standard Water Pressure | 0.05MPa~1MPa |
Power Supply | 220-240V~,50Hz |
---|---|
Washing Capacity | 8.0kg |
Dimension (WxDxH) | 595x565x850 |
Weight | 68kg |
Rated Power | 2000W |
Product Fiches
Product fiche concerning to Regulation (EU) No 1061/2010
Trademark
Model identifier WF81492M
Rated capacity in kg of cotton laundry 8
Energy efficiency class on a scale from A+++ (most efficient) to D (least
efficient) A+++
Energy consumption 196kWh per year, based on 220 standard washing cycles for
the standard cotton programs at 60 °C and 40 °C at full and partial load, and
the consumption of the low-power modes. Actual energy consumption will depend
on how the appliance is used.
Energy consumption of the standard 60°C cotton program at full load 0.82kwh
Energy consumption of the standard 60°Ccotton program at partial load 0.75kwh
Energy consumption of the standard 40°Ccotton program at partial load 0.73kwh
Weighted power consumption of the off-mode 0.50W
Weighted power consumption of the left-on mode 1.00W
Water consumption 11000 liters per year, based on 220 standard washing cycles
for the standard cotton programs at 60 °C and 40 °C at full and partial load.
Actual water consumption will depend on how the appliance is used. Spin-drying
efficiency class Bona scale from G (least efficient) to A (most efficient)
Maximum spin speed 1400
Remaining moisture content 53%
‘ Intensive 60°C program’ and the ‘ Intensive 40°C program’ are the standard
washing programs to which the information in the label and the fiche relates,
that these programs are suitable to clean normally soiled cotton laundry and
that they are the most efficient programs in terms of combined energy and
water consumption.
Program time of the standard 60°C cotton program at full load 280min
Program time of the standard 60°C cotton program at half load 270min
Program time of the standard 40°C cotton program at half load 270min
Duration time of left-on mode 1min
Airborne acoustical noise emissions during the washing phase 57dB
Airborne acoustical noise emissions during spinning phase 79dB
‘built-in’ washing machine No
Energy test program: Intensive 60/40 °C; Speed: the highest speed; Other as
the default.
Supplier’s name or trademark:
Supplier’s address (b):
Model identifier: WF81492M
General product parameters:
Parameter | Value | Parameter | Value |
---|---|---|---|
Rated capacity (a) (kg) | 8.0 | Dimensions in cm | Height |
Width | 60 | ||
Depth | 57 | ||
Elia) | 60.0 | Energy efficiency class (a) | B |
Washing efficiency index (a) | 1. | Rinsing effectiveness (g/kg) (a) | 5.0 |
Energy consumption in kWh per cycle, based on the eco 40-60 pro-gram. Actual
energy consumption will depend on how the appliance is used.| 0.545 0.| Water
consumption in liter per cycle, based on the eco 40-60 program. Actual water
consumption will depend on how the appliance is used and on the hardness of
the water.| 48
The maximum temperature inside the treated textile ( )(°C)| Rated
capacity| 34| R
Remaining moisture content
(a) (%)| Rated
capacity| 54.
Half| 29| Half| 54.
Quarter| 21| Quarter| 54.
Spin speed (a) (rpm)| Rated
capacity| 1400| Spin-drying efficiency class (a)| B
Half| 1400
Quarter| 1400
Programme duration (a) (h:min)| Rated
capacity| 3:38| Type| free-standing
Half| 2:48
Quarter| 2:48
Airborne acoustical noise emissions in the spinning phase (6) (dB(A) re 1 pW)|
76| Airborne acoustical noise emission class (a) (spinning phase)| B
Off-mode (W)| 0.50| Standby mode (W)| N/A
Delay start (W) (if applicable)| 4.00| Networked standby (W) (if applicable)|
N/A
Minimum duration of the guarantee offered by the supplier (b):
This product has been designed to release silver ions during the washing
cycle| NO
---|---
Additional information:
Weblink to the supplier’s website, where the information in point 9 of Annex
II to Commission Regulation
(EU) 2019/2023 (1) (b) Is found:(a) for the eco 40-60 program.(b) changes to
these items shall not be considered relevant for the purposes of paragraph 4
of Article 4 of
Regulation {EU) 2017/1369.
(c) if the product database automatically generates the definitive content of
this cell the supplier shall not enter these data.
NOTE
- Program setting for testing in accordance with applicable standard En60456 for a wash.
- Program setting for testing in accordance with applicable standard En50229 for wash and dry.
- When using the test programs, wash the specified load using the maximum spin speed.
- The actual parameters will depend on how the appliance is used and may be different from the parameters in the above-mentioned table.
- The household washing machine is equipped with a power management system. The duration of the left-on mode time is less than 10 minutes.
- The noise emissions during washing/spinning for the standard washing cycle at full load.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>