xavax 00110225 Stacking Kit for Washing Machines/Dryers Instruction Manual

xavax 00110225 Stacking Kit for Washing Machines/Dryers Instruction

Manual

xavax 00110225 Stacking Kit for Washing Machines/Dryers

Stacking Kit

Thank you for choosing a Xavax product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference.
If you sell the device, please pass these operating instructions on to the new owner.

1. Explanation of Warning Symbols and Notes

Warning

This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

2. Package Contents

• 1 Stacking kit
• 2 Foam strips
• 1 Lashing strap
• This operating instructions

3. Safety Notes

Warning – Installation

• Ensure that the washing machine and dryer are disconnected from the mains power before installation.
• For a stacked washer-dryer installation, the tumble dryer (A) must always be positioned on top of the washing machine (B).
• The product is intended for private, non-commercial use only.
• Use the product for its intended purpose only.
• Do not modify the product in any way. Doing so voids the warranty.
• Once you have mounted the product and the attached load, check that they are sufficiently secure and safe to use.
• You should repeat this check at regular intervals (at least every three months).
• When doing so, ensure that the product does not exceed its maximum permitted carrying capacity and that no load exceeding the maximum permitted dimensions is attached.
• Make sure that the product is loaded symmetrically.
• During adjustment, ensure that the product is loaded symmetrically and that the maximum permitted carrying capacity is not exceeded.
• Children are not permitted to play with the device. Children may not clean the product or perform user maintenance without supervision.
• The pull-out plate is only suitable for holding laundry or a laundry basket. Never place children or pets on the pull-out plate!
• The positioning of the cables of electrical home appliances must comply with electrical and technical regulations. Do not twist, crush or cut the cabl

Note

Use a spirit level to ensure that the finished washer/dryer column is exactly level. Ensure that both units are standing safely and securely with no room to move and check this every
time before using the appliances.

Warnung – Lashing strap

Only use the lashing strap for the purpose described; do not use it for lifting loads. Do not tie knots in the lashing strap and do not lash it across sharp edges. Avoid hot areas > 90°C. Check the lashing and its tension at regular intervals. Do not use the strap or the lock if they are damaged. Max. lashing capacity 800 daN.

4. Installation

Universal stacking kit for securely attaching a dryer to a washing machine: the side rails prevent the dryer from moving when the washing machine vibrates. Includes a sliding plate (holds up to 10 kg), practical storage and work surface at comfortable working height (e.g. for folding laundry, putting laundry into the machine, taking out, etc.)

• The stacking kit frame and shelf plate come preassembled!
• To install the washing machine, you must first pull out the shelf plate. Raise the end of the plate slightly and then remove it in an upward direction.
• Place the stacking kit frame parallel to the washing machine cover. The rollers on the side beams must face forward. The handle of the shelf plate will hang over the frame after installation is finished, so place the frame so it is slightly set back.
• The side beams must lie straight on the washing machine cover. Generally, washing machine covers have raised edges.
• Cut the foam strips to fit the depth of the stacking kit frame. Affix the foam strips to the top of the stacking kit frame.
• For safety reasons, the stacking kit frame must be screwed on to the washing machine cover using the 4 screws included in the kit. Ensure that the screws do not damage any of the underlying washing machine components. Place your dryer on the stacking kit frame. Once again, the previously attached foam strips act as padding. The dryer feet must be screwed all the way in and may not rest on the pull-out shelf plate. It is possible that the feet may have to be completely removed, so that the body of the dryer is truly only resting on the side beams.
• Mount the shelf plate and check that it moves easily.
• Secure the stacked dryer/washing machine arrangement using the lashing strap provided to prevent the dryer from toppling over, e.g. due to pulling on the door. Fit the strap around the entire column (i.e. washing machine and dryer), feed it through the clamping lock and pull it tight.

5. Technical data

6. Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe
the operating instructions and/or safety notes.

Distributed by
Hama GmbH & Co KG
86652 Monheim/Germany

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>