Creek Wearable C1024 Smart Watch User Guide

CW Watch S6 G
User Guide

Your CW Watch S6 G

Steps for Use

You can follow these steps to use CW Watch S6G: ①Wear→ ②Power On→ ③Set up → ④Start using
The following steps will take approximately 5 to 10 minutes, please schedule a suitable time.
① Wear Your Watch
Step 1: Thread the longer band through the first loop of the shorter band.
Step 2: Adjust to a comfortable tightness, then press the holes on the longer band onto the metal pin buckle of the shorter band.
Step 3: Insert the longer band into the second loop of the shorter band and tighten.

② Power On
Press the Digital Crown until the startup screen appears.

Note: If the watch can’t power on, it may be because the battery has drained due to long periods of inactivity. Please charge it far approximately 10 minutes and wait for it to power on automatically.
③ Set up the Watch
Step 1: Download the Fitbeing app
Go to the app store on your phone, search for Fitbeing, and install it.
For Android phanes, go to the Google Play.
For iPhone, go to the App Store.
You can afso scan the QR cace on the left to quickly go to the Fitbeing app in the app store, and install it.

https://app.fitbeing.com/#/code/caB8

Step 2: Pair with the App
Open the Fitbeing app and select “Set Up a Device” on the home page. Follow the instructions to pair your “CW Watch S6 G’ via Bluetooth. Then you can start using the watch.

Attentions:

1. To prevent connection issues between the app and the watch, please do not pair directly within the Bluetooth device list in your phone’s system settings.
2. To ensure successful pairing. please grant Frtbeing App permissions to access Bluetooth, Location, and Camera on your phone.

④ Get Started
Touchscreen Operation
Support full-screen touch (swipe, tap, touch and hold)

Digital Crown Operation
Press

1. Press the digital crown to wake up the screen
2. Press the digital crown to enter the app center from the watch face screen.
3. Exit the app

Long press for 8 seconds to force restarting the watch.

Rotate

1. Toggle between screens or navigate through menus.
2. Adjust the valume of prompt tones and phone calls.

Common Functions

| Notification Center
Swipe down on the watch face screen.
---|---
| Control Center
To access the Control Center, swipe up on the watch face screen. Enable features like Silent Mode, Sleep Mode, Always-on Display, and adjust brightness and volume swiftly.
| Tiles
To switch quickly between the Activity, Heart Rate, Sleep, Suggestions, Weather, or Workout tiles, swipe left or right on the watch face screen.
| Change the Watch Face
To change the watch face, press and hold the screen for 1 second to access the watch face gallery.
| Record Workouts
To start your workout recording, access the Workout app and select a specific workout.
For outdoor workouts, wait in an open area until the GPS connects. The blinking icon “ ” shows it’s acquiring a location fix and will stop blinking upon success.
| Health Metrics Measurement
When wearing the watch, it automatically measures health data such as heart rate, sleep. stress, and activity. You can also view and track this data in the application.

Amazon Alexa

How to wake up Alexa?

1. Press and hold the crown (approximately 2 seconds) ta start using it. Button mapping needs to be set in advance in the app.
2. In the Alexa primary card, tap on the Alexa icon.
3. In the app list, tap on the Alexa icon.

Prerequisite:

1. Sign in to your Amazon account in the app in advance (My Watch -> Amazon Alexa).
2. Ensure that the watch is connected to the app.
3. Ensure that your network connection is stable.

Alexa allows you to use voice commands to listen to news, check the weather, control smart devices, and more. You can control Alexa-compatible speakers, lights, and thermostats with your voice.
On your watch, you can use voice commands to set alarms, timers, reminders, check the weather, and add items to your shopping list, among other things.
When setting up recurring alarms, it is important to ensure that the alarms are synced with the app after each ring. Failure to do so may result in the alarm not ringing at the next scheduled time.
You can access and manage your alarms, timers, and other settings by entering the Alexa app. When ‘ you need to delete an alarm or timer, launch Alexa and verbally command the specific alarm or timer you want to delete.

Install New Watch Faces

In the Fitbeing app, navigate to the Face Gallery page to pick up your preferred watch face.

Charge the Watch
To charge the watch, connect the charging cable to a USB power source. Attach the other and to the charging contact on the back of the watch. The watch will display a charging icon while it is being charged.
Note:
– Make sure the USB charging plug is at the same side as the crown.
– Ensure to use a standard USB power source with an output of 5V™1A or above.
– Prior to charging, ensure to clean the charging contacts of the watch to eliminate any lingering sweat or moisture.

Change the Band

Remove band

1. Lift the spring bar from the groove.
2. Push and hold the spring bar.
3. Pull it out gently to remove the band.

Install band

1. Insert the metal pin at position “A” in the hole.
2. Push and hold the spring bar.
3. Press the band into the body and release the spring bar.
4. Pull the watch band to confirm the firm installation.

Wear and Care

• It is advised to remove the watch for approximately one hour daily. If you experience discomfort or irritation like redness, tingling, or a burning sensation, take off the watch and rest your wrist.
• To maintain hygiene, regularly clean your watch and wrist, particularly after warkouts and sweating. Avoid using hand soap, shower gel, dishwashing liquid, or Cleaning wipes as they can cause skin irritation. Instead, use mild soap and fresh water to clean the band.

Wear Your Watch

For optimal data accuracy please observe the following guidelines while wearing the watch:

1. Wear the watch at a position approximately two finger-widths from your wrist bone.
2. For comfort, adjust the band to allaw a finger’s width between it and your wrist. This ensures both contact and fit.

Key Specifications

Precautions

• Do not replace the built-in battery yourself as it may pose a safety risk.

• Avoid forcibly opening the watch case, as it may cause short circuits and overheating.

• Keep the watch away from environments exceeding 60°C to prevent battery leakage or explosion.

• While the product complies with IP68 waterproof standards, it is not recommended for activities such as bathing, diving, or water skiing that involve high temperatures, steam, or rapid water flow.
  Note that the waterproof perfarmance may be compromised if the product structure is damaged.

• Be aware that firmware upgrades can lead to interface and usage changes. For detailed information, please refer to the product’s upgrade instructions.

Help and Guide

Frequently Asked Questions
If you encounter any problems while using the product, you can access the “Profile – Help & Support” section in the Fitbeing app for assistance.

https://h5.fitbeing.com/#/faq/5vnhl2

Scan the QR code on the right to access or visit help.fitbeing.net for assistance.
Product Manual
You can find the complete product manual in Fitbeing app at “Profile → User Guide”.

https://h5.fitbeing.com/#/instructions/5vnhl2

Scan the QR code on the right to access it, or visit help.fitheing.net to browse.

FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device camplies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. tf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and recerver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an expenenced radio/TV technician for help.

ISED
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>