SNOWJOE LJ602E 5-Ton Electric Log Splitter Owner’s Manual

SNOWJOE LJ602E 5-Ton Electric Log Splitter

IMPORTANT!

Safety Instructions

All Operators Must Read These Instructions Before Use Always follow these safety guidelines. Failure to do so may result in serious bodily injury or death.
General Safety Warnings!
When using the log splitter, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: warning! The use of any other accessory or attachment might increase the risk of injury.
TRAINING Before using the log splitter, take the time to familiarize yourself with the controls, especially how to stop the log splitter in an emergency. Only individuals who have read these instructions and have a thorough understanding of these instructions shall operate the log splitter. Never allow children to operate the log splitter. Retain this manual for future reference and reread it at the start of each log splitting season.

1.  Read, understand, and follow all instructions on the log splitter and in the manual(s) before attempting to assemble and operate. Save this manual for reference and ordering replacement parts.
2.  Never allow children under 18 years old to operate this machine. Children 18 years old and over should be trained and supervised by an adult who understands the operation of the log splitter.
3.  Never allow an untrained individual to operate the log splitter.
4.  Understand the function of all the controls and their proper operation. Know how to stop the machine in case of emergency.

PREPARATION

1.  Plan your log splitting pattern to avoid the discharge of material toward people, pets, and property. Thrown objects can cause serious personal injury.
2.  Always inspect the area where the log splitter is to be used. Ensure the surface the machine is on is 23.6 inch – 29.5 inch (60 cm – 75 cm) high, stable, level and free from overhanging items such as limbs, wires etc.
3.  All visitors: children, adults, and pets, should be kept at a distance from working area, at least 16.5 ft. (5 m) from the log splitter while it is in operation. Stop the log splitter if people or pets enter the discharge area.
4.  Always observe the surface conditions to avoid slipping, falling, and unexpected objects.
5.  Avoid Dangerous Environments – Don’t use appliances in damp or wet locations. Do not operate the log splitter in the rain or wet conditions.
6.  Operation of the log splitter where temperatures are below 41ºF (5ºC) or above 104ºF (40ºC), at a high altitude and/or high humidity may result in a malfunction of the machine. Do not use the log splitter in poor environmental conditions.
7.  Ensure electrical conditions meet requirements (see Electric Safety).
8.  Do not use the machine where gasoline, natural gas or other flammable vapors are present. The electric motor may spark and cause an explosion or fire.

Protective Clothing

1.  Thrown objects can cause serious injury to the eyes and exposed body. Always wear safety glasses or eye shields during operation and while performing an adjustment or repair. Always use face or dust mask if operation is dusty.
2.  Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear protective hair covering to contain long hair.
3.  Always operate wearing adequate protective garments. Dress Properly – Do not wear jewelry or other loose clothing, which could become entangled in moving parts. Wear footwear that provides protection for the feet and ensures sure footing.
4.  Always use ear protection if the noise level exceeds 85 dB. Observe any noise prevention regulations and laws.
5.  Inspect the log splitter for worn, missing or damaged parts and safety labels. See the maintenance section for detailed instructions.
6.  Use the Right Appliance – Do not use this appliance for any job except that for which it is intended.

Wood Condition

1.  Do not split oversized logs (max. log diameter: 10 inch ,max log length: 20.5 inch). Do not attempt to split “hard” wood that requires more than 5 seconds to split.
2.  Ensure the log is free from items that may be projected or cause damage to the machine (ie.: nails, wire).
3.  Ensure the end of the log is cut square and all branches have been cut flush.

OPERATION

Operator Requirements

1.  Only one person shall operate the log splitter. All other individuals and animals shall maintain a safe distance during operation (see safety warning in Preparation).
2.  Always operate the machine in a standing position and in a location that is not in the path of projected debris. The location of the machine should provide safe footing and balance for the operator.
3.  Do not operate the machine while under the influence of alcohol, drugs or physically, mentally fatigued. Always be alert and watch what you are doing!
4.  Contact with the moving parts can amputate body parts. Do not put any part of your body near moving parts.

Workload Requirements

1.  Never exceed the operating capacity of the log splitter.
2.  Always split the log in the direction of the grain. Do not place a log across the log splitter.
3.  Never split more than one log at a time.
4.  Do not load a log when the ram is moving.

Log Splitting

1.  Remove any keys and adjusting wrenches before turning the machine ON.
2.  Do not use accessories or attachments that are not recommended in this manual.
3.  Place the log on the log retention brackets. Do not hold or secure the log with your hands.
4.  Do not split wood that takes more than 5 seconds to split. Doing so will apply excessive pressure on the ram cylinder and damage the machine.
5.  Do not push/force the log onto blade. Always let the blade initiate splitting the log.
6.  If the log moves during operation, stop and reset.
7.  If a log is jammed do not request assistance of a second person. Ensure the machine power is disconnected and built up pressure released before attempting to release log.
8.  Ensure the machine is turned OFF when not in use. If the machine is left unattended then disconnect power to the machine.

MAINTENANCE AND STORAGE

1.  Maintain or replace safety and instruction labels. Ensure safety guards are in place.
2. Disconnect the power and ensure built up pressure has been released from the tool before cleaning, repairing, or inspecting the log splitter.
3. For best operation keep the blade sharp, moving parts lubricated and the machine cleaned.
4. Always check for damaged or worn parts, alignment of moving parts, and tightness of bolts and screws before each use.
5. Replace oil as specified in the Maintenance section. Follow all local regulations and laws concerning disposal of waste oil.
6.  Qualified mechanics and electricians must carry out repairs.
7.  When not in use, always store the machine in a secure location that children cannot access. Store the machine in a dry environment. The machine can be transported or stored in the ambient temperature between 77ºF – 131ºF (25ºC – 55ºC).

Electrical Safety

1.  Ground fault circuit interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for the log splitter. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.
2.  To reduce the risk of electric shock, this appliance has a
3.  prong grounding plug. Use this appliance only with a
4.  To prevent electric shock, use only with an extension cord suitable for outdoor use, such as SW, SOW, STW, STOW, SJTW, or SJTOW. Before use, check that the extension cord is in good condition. When using an extension cord, make sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

WARNING

•  Do not allow any part of the log splitter to make contact with water while it is in operation. If the appliance becomes wet while turned off, wipe dry before starting.
•  Use only a UL-, CSA-, or ETL-rated extension cord for outdoor, all-weather use.
•  Do not use an extension cord over 50 ft (15m).
•  Do not touch the appliance or its plug with wet hands or while standing in water. Wearing rubber boots offers some protection.

To prevent the appliance cord from disconnecting from the extension cord during operation, make a knot with the two cords as shown in Table 1.

Method of Securing Extension Cord

Do not abuse the cord. Never pull the log splitter by the cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil, and sharp edges.

GROUNDING INSTRUCTIONS

1.  In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug.
2.  The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
3.  Do not modify the plug provided – if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
4.  Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
5. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded
6. . Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug.
7. Repair or replace damaged or worn cord immediately.
8.  This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Sketch A in Figure 2. The tool has a grounding plug that looks like the plug illustrated in Sketch A in Figure 2. A temporary adapter, which looks like the adapter illustrated in Sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in Sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box.

PERMANENTLY CONNECTED TOOLS

1.  This tool should be connected to a grounded metal permanent wiring system; or to a system having an equipment-grounding conductor.
2.  USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 2 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

EXTENSION CORDS

1.  Use only three-wire outdoor extension cords that have three-prong grounding plugs and grounding receptacles that accept the appliance’s plug.

Safety Symbols

The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate.

To reduce the risk of injury, user must read instruction manual.

| |

SAFETY ALERT – Indicates a precaution, a warning, or a danger.

|

Wear heavy-duty gloves and steel-toed boots when using the machine and handling debris.

| |

Wear eye and hearing protection. For protection against injury, wear ear defenders and safety goggles.

|

WARNING! Do not expose or operate the unit in rain or wet conditions. Keep dry.

| |

Keep bystanders and children a safe distance away.

|

Moving parts can crush and cut hands and fingers. Keep hands clear of the ram plate, wedge, and logs while splitting.

| |

WARNING! Always be aware of the movement of the log splitter.

|

Disconnect the mains plug if the cord is damaged or entangled.

| |

Keep you hands away from splits and cracks which open in the log. Do not remove jammed logs with you hands.

Know Your Electric Log Splitter

Read the owner’s manual and safety instructions carefully before operating the log splitter. Compare the illustration below to the log splitter in order to become familiar with the location of the various controls and adjustments. Save this manual for future reference.

THE OTHER SIDE

1.  Log pusher
2.  Log rail
3.  Splitting wedge
4.  Bleed screw
5.  Oil drain bolt
6.  Lifting handle
7.  Supporting leg
8.  Log retaining plates
9.  Motor
10.  Appliance cord
11.  On/Off switch
12.  Switch box
13.  Rear wheels
14.  Hydraulic control lever 15 Control lever guard
15. Max pressure limit screw
16.  Beam

Technical Data

• Motor  15A
• Rated Voltage   120V AC 60 Hz
• Splitting Force Max  5 ton
• Ram Force/   5 ton
• Material   Steel
• Log Length Max  20.5 in. (52 cm)
• Log Diameter Max   10 in. (25.4 cm)
• Wedge Height   5 in. (12.7 cm)
• Beam Height   5.5 in. (14 cm)
• Hydraulic Cylinder Size   29.7 in. x 2.3 in.
• (Length x Diameter)  (75.5 cm x 5.9 cm)
• Hydraulic Rod Size 30.2 in. x 1.2 in.
• (Length x Diameter)  (76.8 cm x 3 cm)
• Hydraulic Capacity  1.1 gal (4.2 L)
• Wheel Size  6 in. (15.2 cm)
• Net Weight  92.6 lbs (42 kg)

Unpacking

Carton Contents

•  Electric log splitter
•  Lifting handle
•  Supporting leg
•  Bolts, nuts and washers (4 sets)
•  Manual and registration card
•  Carefully remove the log splitter and check to see that all

Inspect the product carefully to make sure no breakage or damage occurred during shipping. If you find damaged or missing parts, DO NOT return the unit to the store. Please call the Snow Joe® + Sun Joe® customer service department at 1-866-SNOWJOE (1-866-766-9563). NOTE : Do not discard the shipping carton and packaging material until you are ready to use your new electric log splitter. The packaging is made of recyclable materials. Properly dispose of these materials in accordance with local regulations.

Assembly

Place the lifting handle on the supporting leg, fix them together with the provided bolts, nuts and washers. Tighten securely (Fig. 1).

Attach the leg with handle assembly on the bottom of the log splitter, secure with the other 2 sets of bolts, nuts and washers. Tighten securely (Fig. 2).

Operation

Splitting Operation

Follow these instructions to operate the log splitter:

1.  Ensure all logs meet the proper size requirements [(max log diameter: 10 in. (25.4 cm); max log length: 20.5 in. (52 cm)]. IMPORTANT! Logs vary in hardness and structure. Small logs with knots or harder wood may be more difficult to split. Larger logs with less hardness may not be difficult to split. Do not force the log splitter if the log fails to split on the first attempt.
2.  When loading or positioning a log, always handle the bark side; never handle the ends. Never place your hands or body parts between the log and the splitter.
3.  Make sure all moving parts is completely stopped. Never load or unload logs while the log pusher is moving.
4.  Check that bleed Screw is open.
5.  Load the log lengthwise into the unit between the wedge and the log pusher. Be sure that the split will be along the grain. Check to make sure the log is fixed stably.
6.  Plug the appliance cord into an appropriate power outlet.
7.  Engage the log pusher by using your left hand to push the hydraulic control lever and your right hand to push the On/Off switch (Fig. 4). NOTE : This log splitter is equipped with ZHB control system, which requires both the On/Off switch and the hydraulic control lever to be engaged simultaneously to start the machine.
8.  The log pusher will move forward and the log will be split by the splitting wedge.

Duty Cycle

1. The electric log splitter is designed for occasional use. Use over a long period will overheat the motor and may cause damage.
2. The electric log splitter should not operate at 15A load for more than 5 minutes at a time, after which it must be switched off and allowed to cool down for at least 10 minutes before restarting.

Release both the hydraulic control lever and the On/Off switch, the log pusher will move to the original position. Wait until the wood pusher completely stops, and remove the split log.

Removing A Jammed Log

1.  Release both the hydraulic control lever and the On/Off switch.
2.  After the log pusher moves back and completely stops at its starting position, insert a wedge wood under the jammed log (Fig. 5).
3.  Start the log splitter to push the wedge wood to go completely under the jammed one.
4.  Repeat above instructions 2 – 3 with a sharper sloped wooden wedge as needed until the log is free.

Maintenance

General

•  Periodically apply a light coat of rust-resistant oil, such as 3-in-1 oil or WD-40, to the springs to keep them in proper working order.
•  Periodically check all fasteners for tightness.
•  Annually clean and lightly lubricate parts.
•  Use a glossy enamel spray paint to touch up scratched or worn painted metal surfaces.
•  Never exceed the load capacity rating of 5 tons; it will damage the log splitter and void the manufacturer’s warranty.
•  Periodically sharpen the wedge. Use a fine tooth file, take off burrs and smooth rough sections of the cutting edge.

IMPORTANT! If a part needs replacement, only use parts that are specifically recommended by the manufacturer. Replacement parts that do not meet these specifications may result in a safety hazard, may compromise the tool’s performance, and will void the manufacturer’s warranty.

Replacing the Hydraulic Oil

After every 150 hours of use, the hydraulic oil needs to be replaced. The following hydraulic oils or equivalent are recommend for the log splitter’s hydraulic transmission system.

•  SHELL Tellus 22
•  MOBIL DTE 11
•  ARAL Vitam GF 22
•  BP Energol HLP-HM 22

To replace the hydraulic oil, follow the instructions below.

1.  Turn off and unplug the log splitter. Make sure all moving parts have come to a complete stop.
2.  Unscrew to remove the oil drain bolt with dipstick
3.  Turn the log splitter and let it stand on the supporting leg to drain the hydraulic oil off (Fig. 8).
4.  Turn the log splitter and let it stand on the rear wheels, and refill the hydraulic oil into the hole behind the oil drain bolt with dipstick (Fig. 9).
5.  Clean the oil drain bolt before thread them back. Make sure it is tightened to avoid leakage before place the log splitter horizontally.

Storage

•  Before storing, make sure the log splitter is clean and dry. Such upkeep is necessary to ensure years of trouble-free performance.
•  Lightly lubricate all metal surfaces before storing.
•  Store the machine in a secure location that children cannot access. Store the machine in a dry environment. The machine can be transported or stored in the ambient temperature between 77ºF – 131ºF (25ºC – 55ºC).
•  Examine the log splitter thoroughly for worn, loose, or damaged parts. Should you need to repair or replace a part, contact an authorized Snow Joe® + Sun Joe® dealer or call the Snow Joe® + Sun Joe® customer service center at 1-866 SNOWJOE (1-866-766-9563) for assistance.

Service + Support

If your Sun Joe® LJ602E electric log splitter requires service or maintenance, please call 1-866-SNOW JOE (1-866-766-9563) for assistance.

Model + Serial Numbers

When contacting the company or reordering parts, you will need to provide the model and serial numbers of your product. These are found on the decal affixed to the housing or handle of your log splitter. Copy these numbers into the space provided below.

Troubleshooting

Motor does not run

| ****

•       Overload protection device disengaged to protect the log splitter from being damaged

| ****

•       Contact a qualified electrician for opening the switch box to engage the overload protection device inside.

The machine fails to split logs

| •       Log is improperly positioned.

•       The sizes or hardness of the log exceeds the capacity of the machine

•       Wedge cutting edge is blunt

•       Oil leaks

•       Unauthorized adjustment was made on Max. Pressure Limiting Screw. Lower max pressure rating was set.

| •       Reload the log

•       Reduce the log size

•       Locate leak(s) and call the Snow Joe® + Sun Joe® customer service department at 1-866-SNOWJOE (1-866-766-9563).

•       Call the Snow Joe® + Sun Joe® customer service department at 1-866-SNOWJOE (1-866-766-9563).

The log pusher moves jerkily, generating unusual noise or vibrating a lot| • Lack of hydraulic oil and excessive air in the hydraulic system.| •      Check oil level. Refill the hydraulic oil

if needed.

Oil leaks around the ram or from other points.| •       Air sealed in hydraulic system

while operating.

•       Bleed screw is not tightened

before moving the log splitter.

•       Oil drain bolt with dipstick is

not tightened.

•       Hydraulic control valve assembly and/or seal(s) is worn.

| •      Loosen bleed screw by 3 ~ 4 rotations before

operating the log splitter.

•      Tighten the bleed screw up before moving the

log splitter.

•      Tighten the oil drain bolt with dipstick.

•      Call the Snow Joe® + Sun Joe® customer service department at 1-866-SNOWJOE (1-866-766-9563).

OUR WARRANTY:

Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used for ordinary household use for a period of two years from the date of purchase by the original, end-user purchaser when purchased from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from unauthorized sellers. If your Product does not work or there’s an issue with a specific part that is covered by the terms of this Warranty, Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no charge, or (3) repair the Product. How cool is that! This Warranty gives you specific legal rights, and you may also have other rights which vary from State to State.
PRODUCT REGISTRATION:
Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOWJOE (1-866-766-9563), or by e-mailing us at help@snowjoe.com. Failure to register your Product will not diminish your warranty rights. However, registering your Product will allow Snow Joe to better serve you with any of your customer service needs.
WHO CAN SEEK LIMITED WARRANTY COVERAGE:
This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.
WHAT IS NOT COVERED?
This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This Warranty also does not apply if the Product was purchased from an unauthorized seller. This Warranty also does not cover cosmetic changes that do not affect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>