legrand WNRR15 Radiant 15 Ampere Tamper Resistant Electrical Outlet Installation Guide

No: 341309 5/21

radiant® WNRR15/WNRR20 Smart 15A/20A Tamper-Resistant Outlet with Netatmo, Resistive: 120VAC, 60Hz, 15A/20A; Incandescent, Halogen: 1000W/1500W, Standard

• Electronic Ballast: 3.75A/5A; Motor: 1/2 HP/1 HP
  Installation Instructions

Catalog Number(s) : WNRR15, WNRR20
Country of Origin: Made in China

REGULATORY INFORMATION
FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 90 mm between the transmitter’s radiating structure(s) and the body of the user or nearby persons.

NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment.
Contains FCC ID: 2AU5D982057

IC NOTICE: This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

RF EXPOSURE STATEMENT:
This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation distance of 90 mm to the human body.
Note: Any changes or modifications to this device that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment.
IC ID: 25764-982057
HVIN: 982057

BEFORE YOU START

Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities.

Warning: Incorrect installation could result in death, serious injury, and/or damage to your home or devices.
Caution: To reduce the risk of injury and/or overheating and damage to other equipment:

• For dry, indoor use only.
• Do not use to power medical equipment ­ not suitable as a disconnecting means.
• Do not use with loads exceeding the device load rating.
• Connect the smart switch to a 120 VAC, 60 Hz power source ONLY.
• Always use copper wire to install the smart switch & follow all applicable local and national electrical codes.

WHAT YOU NEED

Required:

• Phillips-head screwdriver
• Flat blade screwdriver

You May Also Need:
Voltage tester, pliers, wire cutter, wire stripper, electrical tape, flashlight, wiring leads (included), and wire nuts (included).

INSTALLATION & SETUP

1. Turn off power to device at circuit breaker
   Plug a light or a fan into the outlet and turn it on. Next go the the circuit breaker and turn off the breaker that connects to the outlet. Confirm that power is now out to BOTH outlets.
   NOTE: Ensure power is off to all devices in electrical box.

2. Remove existing device
   Check for the following wires:
   a. HOT or LINE: Receives power from the circuit box. Referred to as “HOT” for the purpose of this guide. Do not touch or let “HOT” wire contact other wires. The box may contain additional LOAD wire to connect to downstream devices.
   b. NEUTRAL: Creates a path to return current to the power source. The box may contain additional NEUTRAL wire to connect to downstream devices.
   c. GROUND: Provides a safe path for electricity in the event of a short circuit.

3. Wire Smart Outlet
   When connecting each wire, loosen the terminal screw, insert the wire into terminal slot, and tighten the terminal screw until the wire is secured.
   a. Connect the WHITE neutral wire(s) in the box to the Neutral Terminal on the device.
   b. Connect the HOT wire(s) in the box to the LINE HOT terminal on the device.
   c. Connect the ground wire from the box to the Ground terminal on the side of the device.
   The grounding terminal screw is Green in color.
   NOTE: This outlet can be optionally wired to control downstream outlets. For more information please see the resources section for this product on the Legrand.us website.

4. Secure Smart Outlet
   **** a. Fold the wires into electrical box, taking care not to pinch a wire.
   b. Use included screws to secure smart outlet to electrical box. Do not fully tighten the screws.

5. Test The Smart Outlet
   NOTE: See getting to know your outlet section for feature details.
   Turn the power back on at the circuit breaker, press button to turn controlled outlet on/off.
   a. Turn the power on at the circuit breaker and check that the indicator light on the smart outlet is on to indicate that it is active.
   b. Plug a lamp or device into the smart outlet.
   c. Press the on/off button to turn the smart outlet on.
   Your lamp or device should power on.
   d. Press the on/off button to turn the smart outlet off.
   Your lamp or device should power off.
   TROUBLESHOOTING TIP: If the device is not powering, visit www.legrand.us/radiant/smart-lighting/support for support.

6. Attach Wall Plate
   a. Use the sub-plate screws (provided) to secure the subplate to the smart outlet.
   b. Tighten device screws to secure to the electrical box.
   c. Angle the UP end of the wall plate over the top edge of the sub-plate. Push the screwless wall plate down and in until it “snaps” into place over the sub- plate.
   NOTE: To remove the wall plate, place the tip of a flat blade screwdriver into the slot under the wall plate and twist gently.

7. Set Up Your System
   a. Download and launch the Legrand Home + Control app. The app is available on the App Store or on Google Play.
   b. Connect your smart device to your home network by following the step by step instructions in the app.
   c. Use the app to control your smart device.

GETTING TO KNOW YOUR OUTLET

for detail.
2| On/Off Button| Turns the controlled outlet on or off
3| Controlled Outlet| Outlet controlled by On/Off button and app
4| Uncontrolled Outlet| “Always on” outlet
5| EZ Button| Use to connect the device to Netatmo network

LED Indicator Light Explanations

Reset To Factory Default
To manually reset the outlet to factory defaults press and hold the EZ Button for 10 seconds until you see the LED blink then release. The device will reset in about 20 seconds after release.

SPECIFICATIONS

Legrand reserves the right to change specifications without notice.

For most recent instruction sheets or more information on WNRR15, please see this link or scan the QR code: https://www.legrand.us/p/wnrr15wh| For most recent instruction sheets or more information on WNRR20, please see this link or scan the QR code: https://www.legrand.us/p/wnrr20wh

LIMITED ONE YEAR WARRANTY

Legrand will remedy any defect in workmanship or material in Legrand products which may develop under proper and normal use within one years from date of purchase by a consumer:

1. by repair or replacement, or, at Legrand’s option,
2. by return of an amount equal to consumer’s purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such remedy by Legrand does not include or cover cost of labor for removal or reinstallation of the product. ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED HEREBY. (Some states do not allow disclaimers or exclusion or limitation of incidental or consequential damages, so the above disclaimer and limitation or exclusion may not apply to you.) ANY IMPLIED WARRANTIES INCLUDING WHERE REQUIRED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE one YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)

To ensure safety, all repairs to Legrand products must be made by Legrand, or under its specific direction. Procedure to obtain performance of any warranty obligation is as follows:

1. Contact Legrand, Syracuse, New York 13221, for instructions concerning return or repair;
2. return the product to Legrand, postage paid, with your name and address and a written description of the installation or use of the Legrand product, and the observed defects or failure to operate, or other claimed basis for dissatisfaction. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

For covering patents, see www.legrand.us/patents
No: 341309 5/21
© Copyright 2021 Legrand All Rights Reserved.

Questions? We’re here to help.
Phone: 1-877-833-3303 8:00 a.m. to 8:00 p.m. EST (M-F)
Email: smartlighting@legrand.us
Chat: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the chat icon to open a dialogue box)

References

• Legrand US | Delivering and Managing Power, Light, and Data
• Legrand CA | Delivering and Managing Power, Light, and Data
• Legrand US | Delivering and Managing Power, Light, and Data
• Patents | Legrand
• The radiant Collection by Legrand
• Smart Lighting from the radiant Collection ⎸Legrand
• Smart 15A Outlet with Netatmo
• Smart 20A Outlet with Netatmo
• Smart Lighting from the radiant Collection ⎸Legrand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>