TRIPP-LITE PDUMV15 Single Phase Metered PDU Owner’s Manual
- June 6, 2024
- Tripp Lite
Table of Contents
TRIPP-LITE PDUMV15 Single Phase Metered PDU
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be followed during
the installation, operation and storage of this product. Failure to heed these
instructions and warnings will void the product warranty.
CAUTION Only those who are properly trained or qualified to use this
device should do so. Anyone who is not trained or qualified should not use
this device unless it is under the supervision of someone who is properly
trained or qualified to do so.
Children must be supervised to ensure that they do not use the device as a
toy. Never use the device if the cord and plug are damaged; if it is not
working properly, or if it has been dropped or damaged, take it to an
authorized service center for inspection and repair. If the power cord is
damaged, it must be replaced by the manufacturer, its authorized service
agent, or by qualified personnel in order to avoid a danger.
Important Warnings
- The PDU provides the convenience of multiple outlets, but DOES NOT provide surge or line noise protection for connected equipment.
- The PDU is designed for indoor use only, in a controlled environment, away from excess moisture, temperature extremes, conductive contaminants, dust or direct sunlight.
- Keep indoor ambient temperature between 32°F and 77°F (0°C and 25°C).
- The PDU must be installed by a qualified technician only.
- Do not attempt to mount the PDU to an insecure or unstable surface.
- Install in accordance with National Electrical Code standards. Be sure to use the proper overcurrent protection for the installation, in accordance with the plug/equipment rating.
- Connect the PDU to an outlet that is in accordance with your local building codes and that is adequately protected against excess currents, short circuits and earth faults.
- The electrical outlets supplying power to the equipment should be installed near the equipment and easily accessible.
- Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that eliminate the connection to ground.
- Be sure to provide a local disconnect device on any models that are permanently installed without a plug that is easily accessible.
- Never attempt to install electrical equipment during a thunderstorm.
- Individual equipment connected to the PDU should not draw more current than the individual PDU’s outlet’s rating.
- The total load connected to the PDU must not exceed the maximum load rating for the PDU.
- Do not attempt to modify the PDU, input plugs or power cables.
- Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable parts inside.
- Do not attempt to use the PDU if any part of it becomes damaged.
- Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended.
Installation
0U Rack Configuration.
Attach the three mounting clips supplied with the PDU to the rack enclosure using the included hardware. The mounting clips should be attached along a vertical plane at equidistant points which roughly correspond to the center and ends of the PDU. The exact mounting configuration may vary depending on the rack and enclosure. If possible, use pre-existing mounting points within the enclosure.
Wall or Under-Counter Configuration
Attach thethree mounting clips supplied with the PDU to a wall or similar flat, secure surface using the included hardware. The mounting clips should be attached along a vertical or horizontal plane at equidistant points which roughly correspond to the center and ends of the PDU. If possible, use pre- existing mounting points. WARNING: Do not attempt to mount the PDU with the outlets facing downward; the mounting clips are not designed to support the weight of the PDU in that manner.
0U Rack Configuration
Attach the included mounting buttons to the PDU. Position the PDU as desired in the rack enclosure, align the buttons with the rack mounting slots, and slide the PDU into position
Attach the PDU to the mounting clips
Using an assistant, place a rear corner of the PDU at an inside edge of the mounting clips, pivot the PDU toward the alternate inside edge and snap into place.
Attach the input plug of the PDU to a grounded outlet.
Insert the plug directly into a grounded outlet that does not share a circuit with a heavy electrical load (such as an air conditioner or refrigerator).
Attach equipment to the PDU.
Do not exceed the load rating of the PDU. The total electrical current used by the PDU will be displayed on the digital meter in amperes (models PDUMV15 and PDUMV20 only).
Optional Installation (Models PDUMV20 and PDUV20)
The PDU includes an adapter that converts the L5-20P input plug to a 5-20P input plug. The adapter is optional; the PDU will work properly without connecting the adapter.
FEATURES
- NEMA 5-15P Input Plug (Models PDUMV15 and PDUV15)
- NEMA 5-15R Outlets (Models PDUMV15 and PDUV15)
- NEMA L5-20P Input Plug (Models PDUMV20 and PDUV20)
- NEMA 5-15/20R Outlets (Models PDUMV20 and PDUV20)
- NEMA 5-20P Plug Adapter (Models PDUMV20 and PDUV20) : The adapter converts the input plug from NEMA L5-20P to NEMA 5-20P.
- Circuit Breaker : If the current drawn by the equipment connected to the PDU exceeds the Maximum Load Rating, the circuit breaker will trip to prevent possible damage. When the circuit breaker trips, its plunger will pop up. Disconnect excess equipment and allow the breaker to cool at least one minute before depressing the plunger to reset the breaker.
- Ammeter (Models PDUMV15 and PDUMV20 only) : The total electrical current used by the PDU will be displayed on the digital meter in amperes.
- Illuminated Power Switch with Cover (Models PDUMV15 and PDUMV20 only)
Warranty & Product Registration
LIMITED WARRANTY
Seller warrants this product, if used in accordance with all applicable
instructions, to be free from original defects in material and workmanship for
a period of 5 years (basic models) or 2 years (metered models) from the date
of initial purchase. If the product should prove defective in material or
workmanship within that period, Seller will repair or replace the product, in
its sole discretion. Service under this Warranty can only be obtained by your
delivering or shipping the product (with all shipping or delivery charges
prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609 USA. Seller
will pay return shipping charges. Visit www.tripplite.com/support before
sending any equipment back for repair.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM
ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER
THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED
BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF
MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET
FORTH ABOVE; THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty
lasts, and some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply
to you. This Warranty gives you specific legal rights, and you may have other
rights which vary from jurisdiction to jurisdiction.) WARNING : The
individual user should take care to determine prior to use whether this device
is suitable, adequate or safe for the use intended. Since individual
applications are subject to great variation, the manufacturer makes no
representation or warranty as to the suitability or fitness of these devices
for any specific application.
PRODUCT REGISTRATION
Visit www.tripplite.com/warranty today to
register your new Tripp Lite product. You’ll be automatically entered into a
drawing for a chance to win a FREE Tripp Lite product! No purchase
necessary. Void where prohibited. Some restrictions apply. See website for
details.
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification,
your Tripp Lite product has been assigned a unique series number. The series
number can be found on the product nameplate label, along with all required
approval markings and information. When requesting compliance information for
this product, always refer to the series number. The series number should not
be confused with the marketing name or model number of the product.
Tripp Lite has a policy of continuous improvement. Specifications are subject
to change without notice. Photos and illustrations may differ slightly from
actual products.