bomaker Odine IV 2.0 Channel Soundbar User Manual

bomaker Odine IV 2.0 Channel Soundbar

www.bomaker.com

Thanks for purchasing BomakerOdine N. This guideline aims to offer you details on setting up this sound bar so that you can enjoy the ultimate sound experience.

ACCESSORIES

4. Power adapter
5. Optical cable
6. AUX audio cable
7. Wall mounting bolts

DIAGRAM (BUTTONS, PORTS & INDICATOR)

1. Power ON/OFF/Mode button. Long press the button to switch on/off the machine, short press to switch mode.
2. Short press to switch to Bluetooth mode,long press to disconnect Bluetooth.
3. Next song/Volume+.
4. Previous Song/Volume-.
5. DC 18V IN Jack.
6. OPTICAL IN: Connect to the compatible devices via an optical cable(provided)
7. HDMl(ARC}: Connect to the compatible devices via an HDMI cable(not provided)
8. USB IN: Connect to the flash drive for playing MP3/WAV files (FAT32 format and 64GB max)
9. AUX IN: Connect to the compatible devices via the 3.5mm RCA stereo jack cable(provided)

MODE

PLACEMENT

A. Table Placement

Place the sound bar on a solid surface.

B: Wall Mounted

REMOTE CONTROL

Battery installation

Use remote control
The working range of remote is +/-30° in both Vertical and Horizontal Direction.

USING YOUR SOUNDBAR

Power Connection

Connect to TV

Use Remote Control or Button on Sound bar to change modes.
Note:

1. Prior to usage, check whether your TV has HDMI ARC, Optical and Aux Output.
2. Prior to using HDMI ARC connection, please ensureyourTV supports HDMI ARC and HDMI Cable is not lower than HDMI 1.4.
3. Turn on PCM settings of your TV When connected in Optical Mode in case there is no sound.
4. 32 is the maximum volume of the sound bar.

Connect to Other Devices

Need to purchase one 3.5mm RCA audio cable if there is only female output on your Devices.

Connect to Bluetooth Device

Long press “BT” button on the remote control or on the soundbar to enter Bluetooth mode. The BT bl: will flash when entering the pairing mode, and bl: will stop flashing once successfully paired

SPECIFICATION

Safety Instructions

1. Avoid dropping
2. Do not disassemble
3. Avoid extreme temperatures
4. Don’t use the device outdoors during thunder storms
5. Use original or certified cables
6. Don’t use any corrosive cleaner/ oil to clean
7. The products should not be exposed to dripping or splashing water

FCC Regulatory Compliance

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment.

RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ISED WARNINGS
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’ s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier Trade Name: Bomaker, Model No: Odine IV
Responsible Party- U.S. Contact Information
Substanbo Inc.
381 Elliot St. Suite llOL Newton, Upper Falls, MA 02464 USA
Tel:+ 1(719)309-2056

Correct Disposal of This Product
(Waste Electrical& Electronic Equipment)
This mark shown on the product or its packaging, indicates that this product should not To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household user should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contact. This product should not be mixed with other commercial wastes for disposal.

Declaration of Conformity

We (Manufacturer is responsible for this declaration)
Guang Dong Substanbo Technology Co , Ltd
(Company name)
Room 2508, Bd.4, Tianan yungu 2nd Industrial Park, Longgang District Shenzhen,China
(Company address)
declare under our sole responsibility that the product
Trade name: Bomaker
Equipment: 2.0 Sound bar system
Model No. : Odine N
to which this declaration relates is in conformity with the essential requirement set out in the Council Directive on the Approximation of the laws of the Member States relating to RED

Directive(2014/53/EU) & RoHS(2011/65/EU) product is responsible to affix CE marking, the following standards were applied:
EN 62479:2010
EN 62368-l:2014+All:2017
EN 55032:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 55035:2017
ETSI EN 301 489-1 V2.2.3(2019-ll)
Draft ETSI EN 301489-17V3.2.0(2017-03)
EN 300 328 V2.2.1(2016-ll)
IEC62321-3-l:2013
IEC62321-4:2013
IEC62321-5:2013
IEC62321-6:2015
IEC62321-7-l:2015
IEC62321-7-2:2017
IEC62321-8:2017
Full Name: Lion Liao  Position:Approbation Manager

bomaKer
EU Representative: E2euro Consulting Hungary
Address: Hoferstasse 9B, 71636 Ludwigsburg, Germany
UK Representative: Substanbo Innovations Technology Limited Address: lOS, 11 Courtenay Road, East Lane East Lane Wembley United Kingdom HA9 7ND
US Representative: Substanbo Inc.

Address: 36 South 18th Avenue, Suite A, Brighton, CO, USA 80601 Manufacturer: GuangDong Substanbo Technology Co., Ltd. Address: 2508, Building 4, Tia nan Cloud Park Phase 11, Bantian Street, Longgang District, Shenzhen, China 518100
+ 1(437)800-0151
support@bomaker.com
www.bomaker.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>