globe GE50402 Smart 4 inch LED Integrated Ultra Slim Recessed Kit Installation Guide
- June 6, 2024
- globe
Table of Contents
globe GE50402 Smart 4 inch LED Integrated Ultra Slim Recessed Kit
SMART RECESSED LIGHTING
Check out product videos on our YouTube channel, on the Globe Smart Home – Amazon Certified for Humans playlist!*
SAVE THESE INSTRUCTIONS
Most electrical accidents are caused by carelessness or ignorance. If you combine a basic knowledge of electricity, a healthy respect for it, and a dose of common sense, you can safely tackle many household electrical repairs. Here are some basic guidelines for working with electricity:
- Before working on a circuit, go to the main service panel and remove the fuse or trip the breaker that controls that circuit. Tape a sign to the panel warning others to leave the circuit alone while you work.
- Before touching any wire, use a voltage tester to make sure it’s not live. Whenever you check for voltage in a receptacle, check both outlets—each may be controlled by a separate wiring circuit.
- To protect children, place safety covers over any unused outlets.
- Always work with enough light to see what you are doing; it’s easy to make mistakes when you’re working in dim light.
Before assembling your lighting fixture, TURN OFF THE POWER and consult a qualified licensed electrician.
- IC-rated for direct contact with insulation
- Energy Star
- Wet-rated
- Airtight per ASTM-E283-04
- CAN ICES-005 (B)
LIMITED WARRANTY: This smart recessed light is warranted to last 3 years
from the date of purchase based on use of 3 hours per day. If it fails before
that time, we will replace it. Send the recessed light, proof of purchase and
register receipt along with your complete name and address to Globe Electric.
See caution text for proper use. This warranty is void if this product is
misused in any way. This replacement is the sole remedy available and
liability for incidental or consequential damage is expressly excluded. This
device is not intended for use with emergency exit fixtures or emergency exit
lights, photocells and electronic timers.
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications made to this product are not expressly approved by the party
responsible and could void the user’s warranty of the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna. Increase the distance between the equipment and
receiver. Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected. Consult the dealer or an experienced
radio/TV technician for help.
RF EXPOSURE The equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This device should be installed and
operated with minimum distance 20cm between the radiator & your body.
USER MANUAL NOTICE FOR LICENSE°EXEMPT RADIO APPARATUS This device
complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. CAN ICES-005
(B).
RADIATION EXPOSURE STATEMENT: This equipment complies with IC radiation
exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the
radiator & your body.
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment. NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
FCC RESPONSIBLE PARTY Globe Electric 15301 Shoemaker Ave, Norwalk, CA 90650 www.globe-electric.com
FEATURES
- LED integrated – dimmable through the app
- RGB: Choose from a full spectrum of colors
- Tunable white (2000 K – 5000 K): Choose from a focused bright white to a relaxed sunset glow
- Manually or remotely control your light with the Amazon Alexa app
- Pair with Amazon Echo to control your light through voice commands
- Set schedules and control your light from anywhere
SPECIFICATIONS
| 540 lumens (at 5000 K) | 9 watt |
|---|---|
| Lasts 50,000 hours | CRI 90 |
| 120 V • 60 Hz | IC-rated |
| Indoor/outdoor use | Minimum starting temperature: -18˚C (0˚F) |
Since 1932, Globe has taken pride in offering products of the highest quality, and a level of service unparalleled in the industry. Should you encounter any difficulties, have any questions or simply wish to offer us your valuable feedback, you may contact us in the following ways: Toll Free Telephone: 1-888-543-1388 (North America Only) / Toll Free Fax: 1-800-668-4562 (North America Only) E-Mail: info@globe-electric.com Mail: Globe Electric Customer Service Department 150 Oneida, Montreal, Quebec, Canada H9R 1A8 Please visit our website to discover other quality Globe products: http://www.globe-electric.com
Planning Installation
Compare all parts with the “Hardware Included” section. If any part appears missing or damaged, do not install this product and contact the Customer Service team at 1-888-543-1388 or e-mail to info@globe-electric.com.
Tools Required
- phillips head screwdriver
- pliers
- electrical tester
Hardware Included NOTE: Hardware is not shown to actual size.
| Item | Quantity |
|---|---|
| light panel + receiver + cable | 1 |
| junction box + cable | 1 |
| foam gasket | 1 |
INSTALLATION
Improper wiring of any electrical device can cause fire, serious injury or death. Always consult a qualified licensed electrician who will ensure the switch is installed in accordance with local electrical codes and regulations. Before starting installation, ensure the power is disconnected at the circuit breaker and test existing switch with a voltage tester.
Caution
-
Make sure that the power at the circuit breaker is off before wiring.
-
Neutral wire is required. Confirm the wall box contains a neutral wire (typically white).
-
The wire colours indicated in this manual are the common colors and may differ in some homes. Please contact an electrician if you have different wire colours.
-
Ensure the wire conductors are securely fastened to each wire.
-
DO NOT USE WITH STANDARD DIMMER.
-
Step 1 Turn power OFF from the electrical panel prior to installation.
-
Step 2 Determine the location for installation and cut a hole of the appropriate size in the ceiling. Refer to the hole diameter table for appropriate sizes or use the supplied template on the “Hole Size” page.
cutting hole diameter- 4 inch slim
- 4 1/4ʺ ± 1/8ʺ (83 ± 3mm)
-
Step 3
- Open the junction box cover and remove the appropriate knockout(s) on the side panel.
- Insert the electrical supply cable through the knockout. If you do not have electrical wiring experience, Globe recommends consulting a qualified licensed electrician who will ensure the fixture is installed in accordance with local installation codes.
- Using quick-connect push-in terminals, connect the green ground wire to the green wire terminal; the black wire to the black wire terminal; the white wire to the white wire terminal.Use the cable clamp to secure wire in knockout hole.
-
Step 4 Place all wiring and connections back into the box and close the cover. Plug the connector cable from the junction box into the light panel, secure with screw cover.
-
Step 5 Insert the junction box through the mounting hole.
-
Step 6 Push spring-loaded clips on the fixture upwards and insert the fixture base into the mounting hole. Release the clips and the fixture will be pulled flush with the ceiling.
NOTE: For airtight requirements, ensure the foam gasket remains between fixture and ceiling. -
Once the fixture has been installed, you’re now ready to pair it with the Amazon Alexa app (see connecting instructions).
CONNECTING INSTRUCTIONS
- Download the Amazon Alexa app.
- Power on your device. Ensure your device has been installed correctly by following the instructions in the “Installation” section.
- Scan barcode
- Launch the Amazon Alexa app.
- Select “Add a Device”.
- Select “Light”, locate Globe Electric and follow the in-app instructions on how to scan the 2D barcode.
Please note: The device is automatically in pairing for 5 minutes once powered on. When you scan the barcode, the white light will flash indicating the pairing is successful. If within 5 minutes, it does not connect, turn the device OFF and ON again to re-enter pairing mode. Please keep these instructions in a safe place. This is the only duplicate of the unique QR code for your product. You may need it to reconnect the product to your account or transfer it to another account.
Don’t have a barcode? Select “Don’t have a barcode?” in the Alexa app and
follow the in-app instructions on how to connect without a 2D barcode.
How to factory reset device If you are struggling to set up your device,
or if the device was already connected to a network, perform a factory reset
by following the instructions below:
- Turn device ON for 10 seconds.
- Turn device OFF and ON 5x. The light will flash RED and then the light will change to WHITE. When the light changes to WHITE, this means the factory reset mode was successful.
- Scan the inner barcode (located on the instruction manual) and connect within 5 minutes. If you fail to connect within the 5-minute time frame, turn device OFF and ON again once to re-enter pairing mode.