ETA210090000 Vital Blend MINI Table Blender Instruction Manual

ETA210090000 Vital Blend MINI Table Blender

INSTRUCTIONS FOR USE

Dear customer, thank you for purchasing our product. Please read the operating instructions carefully before putting the appliance into operation and keep these instructions including the warranty, the receipt and, if possible, the box with the internal packing.

SAFETY WARNINGS

GENERAL PROVISIONS:

• Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.

•  Check whether the data on the type label corresponds with the voltage in your socket. The power supply plug has to be connected to a socket of the electrical installation that conforms to respective standards.

•  This appliance must not be used by children. Keep the device and its supply cord out of reach of children. The device may be used by persons with reduced physical or mental abilities or lack of experience and knowledge only if they are under supervision or they have been instructed about using the appliance safely and understand the potential dangers. Children must not play with the appliance.

•  Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the power socket!

•  Always unplug the appliance from the power supply if you leave it unattended.

•  Be careful when pouring hot liquid into the food processing device or the mixer because it may spurt out of the appliance because of the sudden boil.

•  Be careful when handling the blender, the knife is very sharp!

•  Never use the appliance if the power cord or power plug are damaged, if it is not functioning correctly or if it has fallen on the floor and been damaged, or if it has fallen into the water. In such cases take the appliance to a professional service center to verify its safety and correct function.

•  When the appliance is in operation, prevent pets, plants or insects to get in contact with it.

• After finishing work and before cleaning, always switch off the appliance and disconnect it from the power supply by taking the power cord connector out of the electric socket.

•  Never immerse the drive unit into the water and do not wash it in running water!

•  Do not plug or unplug the appliance from a socket with wet hands and do not pull the power cord!

•  Do not place any objects on the appliance.

•  Do not place any objects on the appliance.

•  Never leave the appliance unsupervised and check it during the whole time
  of preparing meals!

•  The appliance is equipped with a thermal safety fuse that disconnects the current supply in case of engine overloading. If it occurs, unplug the appliance and let the appliance get cooled at least 10 minutes.

•   CAUTION: Do not use the appliance with a program, time switch or any other part that turns the appliance on automatically as there is a risk of fire if the appliance is not covered or placed properly.
  It is not allowed to modify the surface of the appliance in any way (e.g. using a self adhesive wallpaper, foils, etc.).

•  Do not insert the appliance into anybody holes.

•  Use the appliance only with original accessories from the manufacturer.

•  Use the appliance only for the purpose it is intended for as specified in this manual. Never use the appliance for any other purpose.

• WARNING: There is a risk of injury in case of incorrect use (not in accordance with the manual) of the appliance.

•  The manufacturer is not responsible for damage and injuries caused by improper use of the appliance and the accessories (e.g. food deterioration, injury, cutting) and its guarantee for the appliance does not apply in situations when the safety warnings above are not complied with.

USE OF THE APPLIANCE:

• To press the ingredients to the knife, use the attached pusher only! It has been designed especially for that purpose.

•  Every time before the propulsion unit is switched on, the container needs to be attached properly and the lid needs to be placed appropriately so as to close the container. The safety plug or the pusher needs to be inserted in the lid.

•  Never remove or attach the container while the propulsion unit is in operation. Thus you avoid the risk of injury or damage to the appliance.

•  The appliance must not be used in damp or wet environments and in any environment with the danger of fire or explosion (spaces where chemicals, fuels, oils, gases, paints and other flammable or volatile materials are stored).

•  The maximum time of processing is 6 min. After that, keep the break for approx. 10 min necessary for the motor unit to cool off.

•  Correctly placing the bowl on the appliance will release the safety lock and the appliance may be turned on.

•  The container is not designed for keeping and storing food. Put the food in another container suitable for storage after mixing.

•  Do not fill the container with water or other liquid to the maximum. When in operation, the water could overflow and get into the appliance.

•  The product is intended for home use and similar (in shops, offices, and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!

•  Do not switch on the appliance without ingredients put in!

•  Do not remove the lid and dish if the propulsion unit is in operation!

•  Check if the switch is in the (0) position before each connecting of the appliance to the el. outlet and always unplug the appliance from the el. outlet after finishing work.

•  Before removing the lid or container, let the rotating part stop.

•  Do not put more liquid than marked on the dish and always use the lid when mixing or blending liquids.

•  When mixing or stirring liquids, never add more than 2000 ml of liquid, and always use the lid. The maximum hot food volume is limited to 1000 ml.

•  Before preparation, remove possible packages from food (e.g. paper, a PE bag, etc.).

•  Do not process ingredients of higher temperature than approx. 80 °C.

•  If the processed ingredients start to stick on the accessory (e.g. the knife, blender glass or the lid), turn the appliance off and clean carefully with a spatula.

•  Use the mixer only in its working position and at places where there is no risk of tipping and insufficient distance from heat sources (e.g. heater, stove, cooker, grill etc.) and wet surfaces (sinks, basins etc.)

•  Use the appliance only with accessories intended for this type of device. Using another accessory may pose danger for the user.

•  Never put e.g. fingers, forks, knives, spatulas, spoons into the rotating parts of the appliance.

Warning
If the blender runs idle (e.g. the blade cannot touch the ingredients), disconnect it from the mains and release the ingredients. The blender cannot run idle for more than 10 seconds!

POWER CORD:

•  If the power cord of this appliance is damaged, the cord must be replaced by the manufacturer, their service technician or by a similarly qualifi ed person, this will prevent the creation of a dangerous situation.
• Check the condition of the power cord of the appliance regularly.
•  Prevent the supply cord to hang loosely over the edge of the working desk where children could reach it.
•  If you need to use an extension cord, it has to be uncorrupted and it has to comply with the valid standards.
•  The power cord must not be damaged with sharp or hot objects, open fire, it must not be sunk into water or bent over sharp edges. Never put it on hot surfaces or do not let it hang over the edge of a table or work tables. Hitting, stumbling or pulling the power cord e.g. by children can result in tilting over or drawing the appliance down and serious injury!

FEATURES OF THE DEVICE

• propulsion unit
• A1  main switch
• A2  PULSE button for maximum revolutions speed control dial
• A3 speed control dial
• A4 propulsion shaft
• A5  locking mandrel for attaching the container
• A6 rubber feeder
• B – jar
• C – lid
• C1 – plug
• D – pusher

PREPARATION FOR USE

Remove all packaging material, remove the accessory. Remove all adhesive foils, stickers or paper from the appliance. Wash all parts which will come in touch with food in hot water with soap, rinse them thoroughly with clean water and wipe dry or let dry before first use.
Put the blender with the selected accessories on a flat, stable, smooth and clean work surface at the height of at least 85 cm, out of reach of children and incapacitated people. Make sure that the power cord is not damaged and that it does not lead through any sharp or hot surfaces. Plug power supply fork to the electric power. Choose the amount of the processed food so that the maximum volume of the containers marked with the gauge line is not exceeded. Possible short-time mild smoke when the appliance is operated for the first time is not a defect and the appliance is not subject to a complaint for this reason.

main switch (A1)
position (0) – standby mode of the blender
position (I) – switching the blender on (regulated speed)

PULSE button for maximum revolutions (A2)
This is an instantaneous switch (the motor is working at max. capacity and is in operation till the switch is switched over). Switch the PULSE button for maximum revolutions A2 in the lower position (I) and keep it in this position throughout the pulse duration.

Speed control dial (A3)
The speed control dial can only be used if the switch is set in position (I) (regulated speed). By rotating the speed control dial with signal lights indicating operation A3 clockwise, you can smoothly set the rate of speed within the MIN and MAX range.

ATTENTION
The appliance will be put in standby mode only if container B is attached properly, releasing the safety lock.

Putting the container (B) on the driver unit (A)
Put container B on the driver unit A according to Fig. 1. Apply the reverse procedure to remove the container.

Note
There are four positions for proper attachment of container B onto propulsion unit A.

 USING THE BLENDER

Clean and wash the ingredients before processing, or slice them into smaller pieces. Put all ingredients in the container and put on the lid with cap. Put the closed container with the ingredients on the driver unit.
The blender is intended for the preparation of juices, milk cocktails, smoothies, sauces,
ice-cream, soups, baby food, diet food, purées, etc.

Recommendation

• If you process big amounts of food, divide them in separate portions so that you do not overload the motor unit.
•  Soak hard ingredients in water before processing (e.g. legume, soybeans etc.).
•  A minimum quantity of 500g is necessary when processing nuts or making butter. Nuts must be kept within the knife working area by pushing them by stamper during the chopping process.
•  Never remove cover C when the unit is operating.
•  When the appliance is in operation, it is only possible to add liquid ingredients (e.g. water, milk, oil, etc.).
•  Never use the pusher D individually without the lid C.
•  The longer you process the ingredients in the blender, the finer the result will be.
•  You can also process hot liquids up to a temperature of 80 °C, e.g. sauces, soups.
•  Never fill the container with liquids that make foam (e.g. milk) up to 2000 so that they do not overflow. In this case we recommend amounts approx. 1250 ml.
•  If you are not satisfied with the result, turn the appliance off, stir the ingredients using the spatula, remove part of the ingredients or add some liquid.
• Times of preparation (processing) depends on amount, kind, and quality of substances used, normally they are in tens of seconds.

RECOMMENDED SPEEDS FOR PROCESSING INGREDIENTS
This is a high-speed blender. The revolutions are within the range of 15000-28000 RPM. The speed can be regulated smoothly within the MIN – MAX range or you can use the pulse function (the button for maximum revolutions A2). Always set the speed with regard to the kind and amount of ingredients being processed, and particularly with regard to ripeness of fruit and vegetables. We recommend that you always switch on the blender to minimum revolutions and then gradually increase the performance as required. When processing frozen food, always apply the maximum speed even when you are switching the appliance on for the first time.

RECIPES
Consider these following tips for processing examples and inspiration whose purpose is not to provide a manual but to show ways of different food processing. The amount of food to be processed is specified for 1 serving and for 4 servings. If necessary, divide the processed food into more batches in the respective proportion. Never put food in the container, volume of which exceeds the MAX gauge line!

Raspberry smoothie

Ingredients                         Amount (1 serving) Amount (4 servings)

raspberries| 100 g| 400 g
bananas| 1 pcs| 4 pcs
cocoa milk| 150 ml| 600 ml

Procedure:
Clean and wash the raspberries. Remove the banana peel and break the bananas into smaller pieces. Then place all the ingredients in the blender and mix them till smooth.

Cranberry smoothie

Ingredients                         Amount (1 serving) Amount (4 servings)

cranberries| 100 g| 400 g
cranberry juice| 100 ml| 400 ml
yoghurt| 50 ml| 200 ml
strawberries| 50 g| 200 g

Procedure:
Clean the cranberries and strawberries as required. Then place all the ingredients in the blender and mix them till smooth.

Tomato smoothie

Ingredients                         Amount (1 serving) Amount (4 servings)

tomatoes| 150 g| 600 g
tomato juice| 50 ml| 200 ml
apple juice| 50 ml| 200 ml
stalk celery| 20 g| 80 g
carrot| 1 pcs| 4 pcs
ice cubes| 4 pcs| 16 pcs

Procedure :
Clean the vegetables thoroughly and cut them into smaller pieces. Then place all the ingredients together with the ice in the blender and mix them thoroughly.

Watermelon smoothie:

Ingredients                         Amount (1 serving) Amount (4 servings)

watermelon| 200 g| 800 g
strawberries| 50 g| 200 g
water| 100 ml| 400 ml

Procedure:
Wash and dry the strawberries as required. We recommend that you rid the watermelon flesh of the seeds before mixing. In case that you leave seeds in the flesh, you can strain the smoothie through a strainer in the end. Mix all the ingredients thoroughly.

Mango smoothie:

Ingredients                         Amount (1 serving) Amount (4 servings)

mango| 1 pcs| 4 pcs
peaches| 1 pcs| 4 pcs
lemon| 1/2 pcs| 2 pcs
water| 100 ml| 400 ml

Procedure:
Wash the peaches, remove the seeds. Wash the mango, remove the seed and peel it. Then put everything in the blender. Flavour with squeezed lemon juice, if required. Finally, mix everything thoroughly.

Carrot and apple smoothie:

Ingredients                         Amount (1 serving) Amount (4 servings)

carrot| 1 pcs| 4 pcs
apples| 1 pcs| 4 pcs
lemon| 1/2 pcs| 2 pcs
water| 100 ml| 400 ml

Procedure:
Wash the carrot and apples, peel and cut them into smaller pieces. Then put everything in the blender. Flavour with squeezed lemon juice, if required. Finally, mix everything thoroughly.

Green tea and almond smoothie

Ingredients                         Amount (1 serving) Amount (4 servings)

green tea| 200 ml| 800 ml
almonds| 20 g| 80 g
honey| 2 spoonfuls| 8 spoonfuls

Procedure:
First of all, brew strong green tea and allow it to cool down. Put it then together with almonds and honey in the blender and mix thoroughly.

Banana-strawberry ice-cream:

Ingredients                         Amount (1 serving) Amount (4 servings)

bananas| 1 pcs| 4 pcs
strawberries| 50 g| 200 g

Procedure:
Peel the bananas cut them into smaller pieces, and freeze them. Use very ripe bananas. Clean and wash the strawberries as required. If you wish, you can freeze them too (it is not necessary). Then put everything in the blender and mix it. When preparing ice cream, use the pusher to push the ingredients to the knife. Frozen bananas form ice-cream consistency nicely.

Strawberry cocktail:

Ingredients                         Amount (1 serving) Amount (4 servings)

strawberries| 50 g| 200 g
milk| 200 ml| 800 ml
sugar| 1 spoonful| 4 spoonfuls

Procedure:
Clean and wash the strawberries as required. Then put everything in the blender and mix it thoroughly. We recommend using cane sugar for additional sweetening.

Banana cocktail:

Ingredients                         Amount (1 serving) Amount (4 servings)

bananas| 1 pcs| 4 pcs
milk| 200 ml| 800 ml
sugar| 1 spoonfuls| 4 spoonfuls

Procedure:
Peel the bananas and cut them into smaller pieces. Then put everything in the blender and mix it thoroughly. We recommend using cane sugar for additional sweetening.

STORAGE:
After cleaning, store the appliance in a dry, dustless, safe place, out of reach of children and persons sui juris.

 MAINTENANCE

Do not use coarse and aggressive cleaning agents (e.g. sharp objects, scrapers, diluting agents or other solvents). Clean drive unit with a soft and wet cloth with a little detergent. Clean all accessories in hot water with a detergent right after use (do not use a dishwasher). To clean the knife, pour ca. 0.5 l of pure water into the container, switch on the appliance and clean the knife with a few pulses. In case of larger contamination of the knife, repeat the procedure several times, or pour 1 l of water, add a small amount of detergent and switch the blender on for 1 minute.

Some ingredients can color the accessories in some way. But the change does not affect the function of the appliance and it is not a reason for a claim. This coloring usually disappears after some time. Never dry plastic moldings over a heat source (e. g. heater, electric/gas stove). Store the appliance after cleaning at a dry, dust-free, and safe place, out of reach of children and incapacitated people.

Replacing the rubber feeder A6
The rubber feeder is inserted in the driver unit shaft and is not fixed there. To remove the feeder, use a suitable tool, such as a small screwdriver or narrow pliers, to take and pull the feeder up (see Fig. 1).

TROUBLESHOOTING

Problem                                     Cause Solution

The appliance won‘t start| Power supply not connected| Check the power cord, the plug and the socket
The mixing bowl are not mounted properly.| Check and fasten to mixing bowl the right position in order to unlock the safety lock
The appliance stops working| The ingredients being processed are too heavy or the container is too full| Switch off the appliance, let it cool down, divide the

processed food into smaller portions and process them gradually

Knife is not rotating or the appliance vibrates too much| The rubber feeder on the driver unit shaft is worn| Replace the rubber feeder with a new one of the same type using a suitable tool (see MAINTENANCE section).

More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by professional service!
Failure to comply with the instructions of the manufacturer will lead to the expiration of the right to warranty repair!
If you are unable to fix the problem, or if you need any further information about the appliance or service centers, please contact your distributor.

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for the production of packing, components and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electric or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be taken over free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal.

Ask for more details at the local authorities or in the nearest collection site. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. If the appliance is to be put out of operation for good, after disconnecting it from power supply we recommend cutting off the power cord and thus it will not be possible to use the appliance again.

 TECHNICAL DATA

• Voltage (V)
• Input (W)
• Container volume (mI) about
• Weight (kg) about
• Protection class of the appliance
• Size of the product (mm)

shown on the type label of the appliance shown on the type label of the appliance 2000

Input in standby mode is < 0,50 W.
Noise level: Acoustic noise level of 80 dB (A) re 1pW
The manufacturer reserves the right to change the technical specifications and accessories for the respective models.
WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS MANUAL:
HOUSEHOLD USE ONLY.
DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.
TO AVOID THE DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

the symbol indicates a WARNING.

References

• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>