vocolinc VP5X SmartBar Plug Instruction Manual

June 6, 2024
vocolinc

SMARTBAR PLUG/PRISE
VP5X

Download the VOCOlinc App
KEEP YOUR QR CODE SAFE
Setup code Code de configuration

Product Overview

VPSX Smartbar Plug can be controlled through Wi-Fi wireless network.
You can switch on / off the outlet and monitor its status wirelessly from anywhere.

1 LED indicator Wi-Fi / Power status
2 Power / Reset Button – Quick press to switch on / off

– Press & hold for about 10 seconds to factory reset

LED Status Indication

Status LED Indicator
Search Wi-Fi Green blinks quickly
Adding a device Green blinks slowly
A device added successfully Red blinks slowly S times
Discovering a device Red blinks slowly 5 times
Connected to Wi-Fi (Outlet On) Green staying on
Connected to Wi-Fi (Outlet Off) Indication LED stay off
Disconnected from Wi-Fi Red blinks quickly
Reset Press & Hold for 10s -4 red blinks once -‘ green blinks quickly
OTA in Progress Red blinks slowly
OTA done Red blinks quickly 4 times

Features

  • Smart Controls
  • Works with Apple HomeKit
  • Works with Amazon Alexa
  • Works with the Google Assistant

Factory Resetting

Press & hold the reset button for about 10 seconds to factory reset Note: all connection data will be cleared. VPSX must be removed from the app and then added back again.

What’s Included

  • User Manual
  • VPSX Smartbar Plug

Electrical Ratings

Smart AC Outlet
Input: AC 120V, 60Hz
Output: AC 120V, 15A Max, 1800W (Pure Resistive Load)
General use ONLY Indoor dry location use ONLY

System Requirements

  • Mobile device running the latest IOS / Android 4.3 or later
  • Existing Wi-Fi network
  • Stable Internet with good signal strength

Safety Warnings

  • Plug directly into the electric outlet (not into an extension cord)
  • For indoor use only
  • Unplug from VPSX before cleaning
  • DO NOT clean with liquid
  • DO NOT remove the ground pin (round pin) as there is risk of electric shock
  • DO NOT use in wet or damp areas
  • Keep children away from VPSX
  • DO NOT exceed the recommended electrical ratings
  • DO NOT use in precision timing applications where inaccurate timing could be dangerous (sunlamps, saunas, etc.)
  • DO NOT use with devices that should not be operated unattendedly
  • After switching off the main power, DO NOT operate until the main power indicator goes completely off (about 2 seconds delay)
  • DO NOT use the device when the casing is broken

FCC Declaration

Caution: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

IC Declaration

Caution:
This device complies with Industry Canada’s license-exempt RSS. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. In order to avoid the possibility of exceeding the ISEDC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals