VOCOlinc VC1 Smart Indoor Camera User Guide
- June 5, 2024
- vocolinc
Table of Contents
VC1 Smart Indoor Camera
VC1
Smart Indoor Camera
- Lens
- Light sensor
- Infrared LED
- Microphone
- Speaker
- Indicator lights
- Reset button
- Power port
Vc1 key UI indicator Description
Press and hold the key for 10 seconds| The device is reset, the red and blue
lights flash alternately, and the horn gives a short sound
---|---
Power on and not paired (or WiFi is disconnected)| The blue light will flash
slowly
WiFi configuration is successful (start to allow data stream and recording)|
Blue light is always on
WiFi configuration is successful (turn off allow data stream and recording)|
All lights are off
Homekit paired successfully| Blue light flashes 5 times
Upgrade| Blue flash
In video recording (real-time data stream or recording)| The red light is
always on
A short press of a key| No function
Warm note:
Please make sure your router is connected to the Internet.
Easy Set-Up
Step1 Add accessory
Note: the device only supports the addition and use of the home kit
platform under the IOS system.
Please use a 2.4G WiFi access point to configure the device.
The device does not support a 5gwifi access point.
Please open the “home” app in the IOS system, select “+”, scan the setup code
on the body or package as required, and add the device.
You can also search for the “VOCOlnc” APP in the App Store, and add devices to the APP.
Step2 Using and configuring accessory
After adding the device, you can see the device and image preview in the home
interface.
Click preview to enter the full-screen state. You can set the image preview configuration in the full-screen state. After entering the settings, you can set specific functions.
![VOCOlinc VC1 Smart Indoor Camera
- Add accessory1](https://manuals.plus/wp-content/uploads/2022/04/VOCOlinc-VC1 -Smart-Indoor-Camera-Add-accessory1-265x550.png)
Step3 Accessory OTA and pan &tilt control
Due to the limitation of the home kit platform, if the device needs to upgrade OTA or control the pan-tilt rotation, it needs to be controlled through the vocalic app.
Safety Warnings
- For indoor use only
- Unplug from VC1 before cleaning
- DO NOT clean with liquid
- DO NOT use in wet or damp areas
- Keep children away from VC1
- DO NOT use the device when the casing is broken
FCC Declaration
Caution:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
The antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter.
IC Declaration
Caution:
This device complies with Industry Canada’s license-exempt RSS. Operation is
subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept
any interference, including interference that may cause undesired operation of
the device. In order to avoid the possibility of exceeding the ISEDC radio
frequency exposure limits, human proximity to the antenna shall not be less
than 20cm (8 inches) during normal operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>