Zhejiang Balma Lock M001D Smart Chain Lock User Manual

Zhejiang Balma Lock M001D Smart Chain Lock

Product Technical Parameters

Funtion:   Tuya APP+fingerprint
Matching products: padlock, traffic lock,U-shaped glass lock,drawer lock, cabinet lock
Battery: Lithium battery
Fingerprint capacity: 20pcs
Fingerprint reading speed ≤ 0.5 Seconds
working temperature: -10°C-45°C
Working humidity: 40°/oRH-90°/oRH
USB Charging: 5v, Micro USB Interface

Before you do the following, make sure your phone’s Bluetooth is turned on and your phone and padlock are within a reasonable distance. It is recommended to operate within 5 meters.

Connect the APP

Search for “Tuya” APP in the application market and download it. Open the APP.

1.  Click the “+” icon in the upper right corner of the app home page
2. Click on the “Security Sensing” category on the left
3. Find the Door Lock (Bluetooth) and click.
4. Click “start Bluetooth distribution network”,At the same time place your finger on the padlock fingerprint area and turn on Bluetooth
5. Enter the Bluetooth search interface, the device name appears, click “OK” to connect.
6. Prompt connection success
7. Bluetooth unlock, click the unlock button on the device interface to unlock.

Fingerprint management

In the initial state, the device has no fingerprint information. Any finger can unlock.

1. Add fingerprint settings
   Enter the device management interface and click lower right corner Settings- Fingerprint Management-upper right corner “+”-click “user password in the middle of the interface”-click to start collection. Place your finger on the fingerprint area to start fingerprint recognition according to the APP prompt. The sampling is successful, the blue light is on, the red light is faulty, and the continuous sampling is successful 4 times, indicating that the entry is successful. After entering the fingerprint successfully, you can unlock it with the corresponding fingerprint. The green light is on and the buzzer sounds when unlocking is successful. Failure lights up red.

2. Delete fingerprint information
   Open the app, click the corresponding device on the homepage, enter the management interface, click “Settings-Fingerprint Management”, and click the registered fingerprint -delete it.

Fingerprint lock charging instructions

1. When charging, the red light is on; when fully charged, it lights up in green.

2. Low voltage alarm
   After unlocking operation, if the battery voltage is lower than 3.6V. The low- voltage alarm time is about 5 s, the red light flashes once per second, and the buzzer sounds.

3. Low voltage protection:
   When the battery voltage is lower than 3.2 V, it will enter a low-voltage protection state. No matter if you touch the fingerprint or the button, there will be no response. Now you need to plug in USB to charge to restore normal working status.

Product initialization

1. Click the home device ,enter the unlock interface ,click in the upper right corner,enter the next interface
2. Click the remove device in the bottom,it will pop up the interface in the bottom,click on the unbundling and remove the data,initialization successful.

FCC Cautions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>