PEAK PTT-M64G Mobile LTE Communicator User Guide
- June 6, 2024
- PEAK
Table of Contents
PEAK PTT-M64G Mobile LTE Communicator
Main Mic & Noise Reduction
The PTT-MG4G is equipped with two microphones
The palm microphone attaches to the PTT-MG4G at the input jack (7)
The second microphone is built-in (8), and can be activated by simply pushing
the Pl button and speaking
LED LIGHT
The PTT-M64G Status LED Lights include; Power, Network, PTT, WH:i, Bluetooth and GPS.
POWER BUTTON
- Solid Green: Power On
- No Light: Power Off
- NETWORK INDICATOR Flashing Green: Connected To Network Flashing Red Network Connection Lost
- PTT INDICATOR: Transmit Solid Red Receive Solid Red
- BLUE TOOTH: Flashing Orange BT On, No Device Connected. Steady Yellow/Green BT device connected. No Light: BT Off
- GPS STATUS: Flashing Orange Searching For GPS satellites Solid Yellow- Green G PS signal acquired No Light: GPS Off4b not utilized.
Programmable Keys
FCC Warning
15.19 Labeling requirements.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Information to the user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the use(s authority to operate the equipment.
Note: This equipment has been tested and found to comply with: the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protect ion against harmful interference in a residentia I installation. This equipmen t generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmfulminterference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following.
measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet or on a cirruit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE
- 12 Month Limited Manufacturer Warranty
- PeakPTT reserves the right to change hardware, and/or software specifications mentioned in this operating guide without any prior notice. The product specifications and information mentioned here are for reference only.
CHECKLIST
Notice: Please check the box for all above parts, before discarding the packing material. Please contact Peak PTT Immediately, if any parts are missing or damaged
Installation Steps
-
Please Read The Following Instructions Before Installation.
-
Voltage Requirement 12-24 voe RED WIRE: Constant Power. WHITE WIRE: Ignition/Accessory BLACK WIRE Ground.
-
Check screw clearances before installing the radio, to avoid damage to vehicle wiring and other parts.
-
Connect antenna and power cord to the radio before attaching to the bracket Antenna cables are labeled – attach to same labels on radio.
-
Install radio with supplied mounting bracket, to secure radio to the vehicle
-
Install radio in an easily accessible location.
-
Insure proper spacing in back of radio to accommodate wiring harness/associated wires.
-
Be sure to only use 3 amp sized replacement fuses
-
Install the bracket in a location that is accessible.
-
Connect antenna and power cable to the radio before attaching to the bracket
-
Slide the radio into the mounting bracket and secure it using the supplied locking knobs.
-
Install the microphone hanger in an easily accessible location
-
Connect the palm microphone into the jack located on the front panel, attach to hanger.
ADDITIONAL INFORMATION
Avoid Installing the radio where it will be exposed to direct sunlight. Keep the radio free and clear of irrelevant articles to allow for optimal heat dissipation. Do not expose the radio to corrosive agents, solutions or water.
PTT USE
The PTT-MG4G is pre-configured and set-up for PTT service once the device has
been installed, connected to power and turned on. For additional support,
please contact PeakPTT info@peakptt.com
PTT-M64G CLEANING
Use a clean and dry lint-free cloth to remove dust and other fine particles
from the radio. Use an alcohol-free screen cleaner to clean the screen,
control knobs, LCD and jacks Do not use chemicals like stain removers, alcohol
sprays or oil based solutions on the radio. Ensure the radio is completely dry
before use.
CAUTION: Power off the radio before cleaning.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>