PEAK M-CS-BK-2 Wireless Charging Stand Instruction Manual

June 1, 2024
PEAK

PEAK M-CS-BK-2 Wireless Charging Stand

Specifications

  • Name: Wireless Charging Stand
  • Model: M-CS-BK-2
  • Manufacturer: Peak Design
  • Input: 9V2.25A
  • Wireless Output: 5W/7.5W/10W/15W
  • Accessory: 200cm Recycled USB-C to USB-C cable

Product Overview

  1. USB-C Input port
  2. Wireless charging area
  3. Metal support bracket

Usage Guideline

  1. Connect the USB-C end of the provided cable to the USB-C port on the unit, and USB-A end to the wall charger.
  2. Wireless Charging: Place the mobile phone in the wireless charging position to charge it.
  3. Wireless Charging Protection: The device will stop output if\ there is a metal foreign body in the charging position or due to high temperature to ensure safety.

Declaration of conformity

  1. Frequency Range:114.4-148.2KHz; Power H-field: -10.25dBuA/m at 10m (for EU/UK); Frequency Range:356.8-369.6KHz(for EU/UK); Power H-field: -16.74dBuA/m at 10m (for EU/UK).
  2. Hardware version of this product : V2.3, Software version: V0.30.
  3. Hereby, [Peak Design ] declares that the radio equipment type[M-CS-BK-2] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of Conformity is available at the following internet address:
  4. https://www.peakdesign.com/EU-certification.
  5. Hereby, [Peak Design ] declares that the radio equipment type[M-CS-BK-2] is in compliance with UK Radio Equipment Regulations (SI 2017/1206). The full text of the UK Declaration of conformity is available at the following internet address: https://www.peakdesign.com/EU-certification.

RF Exposure Compliance

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20 cm between the radiator and your body. This equipment complies with IC RSS 102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20 cm between the radiator and your body.

FCC  statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

ISED compliance statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence exempt RSS(s). Operation is subject to the following two conditions:

  1.  This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device

Security and Precaution

  • Some phone cases may block the wireless charging.
  • Do not place other materials, like metal objects, magnets, and magnetic stripe cards, between the mobile device and the wireless charger pad.
  • Check your mobile device’s battery percentage using the charging icon displayed on the screen of your phone.
  • When the mobile device is not placed on the charging area accurately, your mobile device may not charge properly.
  • Please do not expose this device to moisture or heat sources.
  • This is not a toy, not suitable for children under the age of 7.

FAQ

Q: What should I do if my phone is not charging wirelessly?

A: Ensure that your phone is properly aligned with the wireless charging area on the stand. Remove any metal objects that may interfere with charging.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

PEAK User Manuals

Related Manuals