EV-PEAK U6Q-1 Fast Charger User Manual
- May 15, 2024
- EV-PEAK
Table of Contents
EV-PEAK U6Q-1 Fast Charger
Preface
- Thank you for purchasing the EV-PEAK Balance Charger. This manual could help you install and operate easily.
- Please read the manual carefully before operating and keep it handy for further reference.
- Items herein mentioned are only supplementary to local safety regulations.
WARNING
Very important to understand the items below. Failure to comply with the mentioned items, would damage the charger or battery, injure your body, or even cause a fire disaster.
- Do not put the charger in inappropriate conditions such as direct sunlight, rain, moisture, and so on
- Keep it away from thermal sources, high voltage, water, flammable gas, corrosive, and so on, be sure to keep it at the range of recommended temperature O” C· 40/32°F-104°F.
- Keep it horizontally stable to avoid any tilt or shake. And be sure to provide it(around>50cm) with enough ventilation during operation.
- Do not put anything or any cover on the radiator or battery during operation.
- Do not charge any non-rechargeable Lithium batteries without specifications.
- Keep the charger and battery on an anti-flammable and anti-conductive surface, and do not put it on the car seat, carpet, and so on to avoid any losses or damages.
- Do not use any voltage out of the specifications, and provide it with the specified type of battery and number of batteries.
- Do not charge or discharge any battery that has been damaged physically.
- Do not plug off the input cable during operating, and plug it off timely once charging is completed.
- Please wipe off any objects attached to the metal ports with a dry cloth.
- Do not disassemble or modify the charger by yourself.
- Do not operate it during thunderstorms.
- Keep children under the age of 14 away from the charger.
- Do not tumble, short-circuit, or reverse polarity to avoid damage before connecting.
- Keep an eye on it during operation.
- Please use a dry powder extinguisher in case of fire, and do not take a liquid extinguisher to avoid electric shock.
Product Introduction
- This product charges 4 sets of lithium batteries at the same time, with a maximum output power of 3000W.
- Two modes of charging and maintenance can be selected. The charging current can be adjusted between slow charging, normal charging, and fast charging.
- It has over-current protection, over-temperature protection, and disconnection.
- Protection, fast equalization, display status indication, and other functions.
- U6Q is highly integrated with the charge butler function. In slow charging mode, 4CH is charged at the same time. In fast charging mode, the battery is charged in cycles according to the saturation and higher battery charging sequence.
- The peak peak current and the maximum charge current can reach 60A; The normal mode charges two batteries at the same time, the charging current is automatically and evenly distributed, and the operation is simple.
- The charger is equipped with an LCD dot matrix display and supports Chinese. English and Japanese display.
- During use, the operating mode, charging voltage, charging current, charging time, battery capacity, and battery cell voltage are automatically displayed.
Part Name
- Main switch
- Inlet
- Charging button
- Balance mouth
- Charging port 1
- Charging port 2
- Maintenance button
- LED indicator
- Handle
- Current adjustment knob
- MICRO_USB Upgrade interface
- AC Input
- cooling fans are the same battery charging port and the balance port, is an independent channel without a balance port; the opposite is the same.
FIRMWARE UPGRADE
Please visit EV-PEAK’s official website to upgrade the firmware if needed and follow the steps below:
- Visit EV-PEAK’s official website www.ev-peak.com
- Connect the charger to your computer via a Micro USB upgrade port.
- Run the firmware and click the “Upgrade” button to upgrade.
- After the upgrade is completed, the equipment will restart.
- If failure to upgrade, please restart steps as above.
Connection instructions
- Connect the power cord to the AC input port and AC power socket (100-240V, 50/60Hz), and turn on the “Power On” switch to start up.
- Connect each LiPo battery pack to the charger via the charging and balance port with compatible connectors as illustrated.
- Before connecting, please check whether the terminals and wiring harness of the battery pack are damaged or disconnected;
- When using the adapter cable, be sure to connect according to the positive and negative signs.
- This charger only supports hybrid charging in fast charging mode!
- Not Support different sets and different types of battery hybrid charging in normal and slow charging modes!
Operating Instructions
The charger is a dual channel with an independent output and an independent interface.
Take either channel of the charger for example as below:
-
Startup and Self-Test
- The charger automatically counts down after getting all the connectors well connected, the LCD screen turning on, and the buzzer alarming. The charger starts charging normally after the buzzer stops. Long press the “Storage” button for more than 2s to function storage.
-
Operation Modes
-
Charging mode: It’s an automatically preferred mode, after getting the battery well connected, the charger countdown self-checks, automatically detects and starts up charging, or bypasses the countdown self-check and directly manual startup.
-
Storage mode: It’s a manual mode, while the battery is idle, recommended to take storage every 15 days; or while the battery life significantly declines or more than SOmV cell voltage tolerance; In storage mode, the charger charges and discharges with trickle current to get each cell voltage balanced to 3.84-3.86v.
-
Continuous working mode: After getting the charging extension manager connected, the charger automatically detects and switches to continuous working mode. In this model automatic mode doesn’t work anymore, the user needs to manually operate and define the continuous working mode once, and then the charger coordinately and continuously works with the charging extension manager until pressing any button to stop or power off.
-
Setting Of Charging Modes
- Based on battery capacity and actual application, adjust the current switch to the right gear.
-
Charging
Long press the charge button for more than 2 seconds to charging mode. -
The red light is on, the charger is charging battery, and the LCD indicates real-time charging status.
-
Green light on. charging finished.
-
Press any key to stop charging.
-
Storage
Long press the charge button for more than 2 seconds to charging mode. -
The red light is on, the charger is charging the battery, and the LCD display indicates the real-time charging status.
-
The green light was on, charging was finished.
-
Press any key to stop charging.
SCREEN
The interface is displayed below:
When the wrong use of charger or failure, the charger will prompt an error message!
As shown below:
Indicator status description
Host indicator
Channel indicator ( The red light flashes for 5 seconds)
Specifications
SUPPORT AND WARRANTY
- Thank you for purchasing our EV-PEAK charger. We do our best to provide you with timely and satisfying support.
- Please contact us with any questions or concerns.
- This product is warranted to be free from manufacturer defects for 1 year from the original purchase date.
- Please keep your original proof of purchase for warranty purposes.
Disclaimer: What our manufacturing warranty does not cover
- Damage caused by incorrect connections.
- Damage caused by incorrect operation.
- Damage caused by impact or drops.
- Damage from disassembly or modification.
- Internal damage from moisture, submersion, dust, dirt or other contaminants.
- Signs of normal wear and tear, scratches dents, and dings.
Note: Any expense exceeding the original purchase price of the charger shall not be borne by EV-PEAK. We reserve the right to modify the contents of this manual at any time with or without notice.
WARNING
- Do not attempt to operate this charger if you are impaired in any way.
- Do not allow children to be near this charger when it is in operation.
- Do not allow children to operate this charger.
- Please turn the power off when the charger is not in use.
- This charger is for indoor use only.
- Shenzhen EV-PEAK New Energy Technology Co., Ltd www.ev-peak.com
- The product specifications and information mentioned in this instruction manual are for reference only and are subject to change without prior notice.
- Copyright © Shenzhen EV-PEAK New Energy Technology Co., Ltd
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>