Haloview BT7 Touch 2.4G Digital 1080P Touch Screen System User Manual

June 1, 2024
Haloview

Haloview-logo

Haloview BT7 Touch 2.4G Digital 1080P Touch Screen System

Haloview-BT7-Touch-2.4G-Digital-1080P-Touch-Screen-System-
image

Specifications

  • Product Name: 2.4G Digital 1080P Touch Screen System
  • Model: BT7 Touch / BT6 Touch
  • Antenna Length: Varies between BT6 and BT7
  • Power Options: DC 10-32V or USB Type-C 5V/2A
  • Screen Size: 5.5 inches
  • Resolution: 16:9, 1024×600 (BT7) / 1280×720 (BT6)
  • Camera Inputs: 4 wireless inputs
  • Recording Format: AVI signal format, supports single-channel and 4-channel composite recording
  • Additional Features: Upgraded touch screen, auto-dim function, camera night LED control, touch screen invalidation during triggering function

Product Usage Instructions

1. Powering the Device:

The device can be powered by either a DC 10-32V input or a USB
Type-C 5V/2A input. Ensure proper cable connections to avoid damage
to the monitor. Disconnect power cables when not in use.

2. Installation:

Suction Cup Mount:

  1. Adjust monitor height by sliding it up or down in the slot and tighten the knob.
  2. Loosen the lower knob on the suction cup mount to adjust the monitor angle to the desired position, then re-tighten the knob.

3M Mount:

This multi-purpose multi-angle adjustment display mount can be used for flexible positioning.

3. Camera Wiring:

Method 1 (Recommended):

Ensure green wires are left unconnected. Connect the camera plug and green wires. Connect the red and green wires to a 10-32VDC power source and the black wire to the negative/ground source.

Method 2:

Connecting the camera plug and green wires. Connecting the red and green wire to 10-32VDC power source, connect the Black wire to Negative/Ground source.

Note: Touch Screen functionality is disabled when the triggering function is activated.

FAQs

  • Q: What should I do if the touch screen is unresponsive?
    • A: The touch screen may be disabled when the triggering function is active. Ensure that you are following the correct camera wiring method to avoid touch screen issues.
  • Q: Can I power the device using a USB Type-C cable?
    • A: Yes, the device can be powered using a USB Type-C cable with a 5V/2A power input.

1. The device can be powered by DC 10-32V or USB Type-C 5V/2A. 2. Improper cable connections may damage the monitor. Remove the power cable connections
when you do not intend to use the device.
1

2

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
3

7″ or 5.5″ Monitor

Camera

3M Mount Bracket

Suction Cup Mount Bracket

Power Adapter for Furrion Pre-wired RV

Pairing Cable

Cigarette Lighter

Type-C Cable

Camera Conversion Cable

The product is under continuous improvement and the specifications will change without notice. Picture for reference only. Please refer to the actual product and accessories. The antennas of BT6 is shorter than BT7, please refer to the actual product received.
4

1. Upgraded touch screen for easy operation. 2. NORMAL, MIRROR, FLIP and MIR- FLIP viewing available. 3. Split mode auto-scan mode and single-display mode available. 4. Support 4-channel composite and single-channel recording in AVl signal format. 5. Auto dim function available. 6. 4 wireless camera inputs. 7. Video input:1080P. 8. Wide voltage input: DC10-32V or USB Type-C 5V. 9. Camera night LED can be turned ON/OFF via monitor.

7″ 16:9 1024×600 1000 Max.6W

5.5″ 16:9 1280×720 550 Max.4.5W 800:1

256G DC10-32V USB Type-C 5V

5

PAIR button Light Sensor Micro SD Card Slot

Power button USB Type-C DC

Power Indicator It turns to red when the monitor is powered on.
6

Speaker

Installation of Suction Cup Mount: 1. Adjust monitor height by sliding monitor up or down in slot, then tighten knob.
Adjust monitor angle by loosening lower knob on suction cup mount, tilting monitor to desired angle and re-tighten knob.
2. Installation of 3M Mount
7

This multi-purpose multi-angle adjustment display mount can be used like below
8

Camera Wiring Method 1: (Suggested)

PLEASE MAKE SURE GREEN WIRES UNCONNECTED

Green

Green

Green

Camera Wiring Method 2:
Green

Green

Notice: Touch Screen invalid when triggering function activated. If you use the camera for long-hour observation, please do not follow Camera Wiring Method 2.
Connecting the camera plug and Green wires. Connecting the red and green wire to 10-32VDC power source, connect the Black wire to Negative/Ground source.
This wiring method can achieve camera triggering function. For example, if the green wire is connected to left turn signal light, the monitor will switch to this camera every time the left turn signal light is turned on. For multi cameras, triggering function can help switch screen display automatically without manually switching channels of cameras to avoid diverting the driver’s attention during driving.
Monitor Wiring:
Connect the monitor to the cigarette lighter power adapter. Power the monitor through the vehicle’s 12V cigarette lighter or USB Type-C.

15
9

15

CH1

CH1

10

2
2 Image freezing may occur when the vehicle is 42-65ft long and the antenna is mounted in a poor location (the antenna is not placed on the roof of the vehicle or there is obstruction around the antenna). In this case, it is recommended to purchase the Haloview 10M or 12M antenna extension cable and place it on the roof without any obstacles.
It is recommended to choose an antenna length that is 2-3ft longer than the length of the RV.
To achieve better signal, it is recommended to purchase the Haloview antenna extension cable and place it in front of the RV where near the roof without any obstacles.
11

If you get poor signal reception, or signal cannot reach at

least 2 bars, please keep the antennas perpendicular and

CH1

adjust the angle of antenna to find best signal reception

position.

Shortcut Menu

Tap the screen when in single image mode, it pops-up the first group of shortcut MENU. You can easily switch to each of the four channels of cameras or go to Quad Mode.
Tap to go to Main MENU.

CH1

REC

CH1 CH2 CH3 CH4 QMODE

Tap the screen again, it pops-up the second group of shortcut MENU.

CH1

REC

SCAN
12

Tap to turn on/off parking line in current channel of camera. When parking line is turned on, exit the shortcut menu to display the parking line. Tap to turn on/off voice in current channel of camera. Tap to adjust the screen brightness. Tap to turn on/off current camera night light. When camera night light is turned on, the indicator will turns from to . Tap to start recording or pause recording. Tap SCAN to automatically switch channels of cameras.
In quad mode (QMODE), an audio icon highlighted in CH1 that has the audio active.

CH1

REC CH2

CH3

CH4

Tap any of the audio icon to hear the audio of any channels of cameras.

CH1

REC CH2

CH3

CH4

13

The audio icon is highlighted to indicate that audio is turned on for that channel.

CH1

REC CH2

CH3

CH4

Notice: Please tap the audio icon instead of other areas. Otherwise the display will switch to the certain channel of camera.

Press

to go to Main Menu

CH1

REC

SCAN

Press

to exit.

9.1 MENU

CH1

REC

SCAN
14

9.2 VOLUME
CH1

REC
9

MUTE

OFF

Tap

to get access to VOLUNE setting

Tap the bar to adjust volume. Tap ON/OFF to MUTE or UNMUTE the volume.

PAIRING

CH1

REC

Please Press Pair key on Camera or Transmitter Box
50

Camera and monitor are paired at the channel of CAM4 as factory default setting. When you open the box, power on the monitor and camera, tap the monitor to find the first group of shortcut Menu and tap CH4, the image will be displayed. Otherwise, please try below methods for pairing.

Tap

to get access to Main Menu. Tap

to enter pairing status, you will

have 50 seconds for pairing. Press the pairing button on the bottom of the camera

until you hear a “tah”. Video will be displayed after pairing complete.

PAIR button

15

Quick Access to Pairing Status: Press the PAIR button for 3 seconds to enter pairing status.

PAIR button
If you press the pair button by mistake and the monitor enters the pairing status, you can tap to exit the pairing status.

CH1

REC

Please Press Pair key on Camera or Transmitter Box
50

9.4 PICTURE
CH1

REC
9 9 9
ON

Tap

to get access to Main Menu. Tap

to enter Picture setting.

Tap the bars to the adjust BRIGHTNESS/CONTRAST/COLOR.

Tap ON/OFF to turn on/off the current camera night led light.

16

9.5 MIRROR

CH1

REC

Tap

to get access to Main Menu. Tap

Tap Normal/Mirror/Mir-flip/Flip at your will.

9.6 QMODE

to enter MIRROR setting.

CH1

REC

13
SPLIT-1/3

14
SPLIT-1/4

23
SPLIT-2/3

24
SPLIT-2/4

34
SPLIT-3/4

4 12
TRIPLE 1

4 13
TRIPLE 2

4 23
TRIPLE 3

12 4
TRIPLE 4

13 4
TRIPLE 5

23 4
TRIPLE 6

4 21
TRIPLE 7

3 12
TRIPLE 8

3 21
TRIPLE 9

12 34
QUAD 1

1

3 4

2

QUAD 2

2

3 4

1

QUAD 3

Tap

to get access to Main Menu. Tap

Tap any of desired display mode.

SETTING

to enter QMODE setting.

CH1

REC

CAM
TRIGGER
COLOR-SYS

ON NTSC

AUTODIM

ON

SCREEN OFF

0

17

Tap

to get access to Main Menu. Tap

Tap ON/OFF to turn on/off Trigger.

Tap NTSC/PAL to switch video format.

to enter.

Tap ON/OFF to turn on/off Autodim. When Autodim is turned on, monitor will automatically decrease brightness in low light. Tap the bar from 0 to 45 to set screen off duration. If 0 is selected, the screen stays on. If 45 is selected, the display will turn off after 45 seconds of inactivity.

9.8 SCAN

CH1 ON ON
CH3

REC
ON
CH2
ON
CH4 45

Tap

to get access to Main Menu. Tap SCAN to enter SCAN setting.

The SCAN function allows the monitor to automatically switch channels of cameras.

In the shortcut menu, you can tap

to start Scan or exit Scan. A Scan icon will

appear on the display if the display enters scan mode.

18

9.9 PARK-LINE

CH1

REC

Tap

to get access to Main Menu. Tap to enter parking line setting.

You can slide the screen to adjust the inclination and the width of the parking line.

9.10 RECORD

CH1
REC. RECORD FORMAT
COVER
TIME

REC
ON OFF
ON
2023/12/03 00:00:00

Tap

to get access to Main Menu. Tap to enter RECORD setting.

Please insert TF card in TF card slot, max 256G Micro SD card.

Note: TF card must be formatted before using. Tap Format ON and Confirm Format.

After TF card is formatted, a yellow folder icon will be shown on the screen,

indicating TF card is available now.

19

When COVER is turned on, overwrite function will be activated. Previously recorded video files will be overwritten when TF card memory is full.
Note: When in QUAD or SPLIT display, the monitor will record all displayed channel of CAM at the same time.
TIME Setting:

CH1
REC. RECORD FORMAT
COVER
TIME

REC
ON OFF
ON
2023/12/03 00:00:00

Tap Year/Month/Date/Hour/Minute/Second, it will pops-up and , tap and to adjust Year/Month/Date/Hour/Minute/Second.
9.11 PLAY

Free : 20.69G Total : 29.73G

DCIM

FOLDER

Tap

to get access to Main Menu. Tap to enter PLAY setting.

Tap

to select, Tap and to move up or down.

Tap

to play the selected file.

Read the SD card through PC, there will be two formats of files. It is suggested to play the AVI format file for higher video resolution.

20

9.11 Trigger Function

Tap

to get access to . The Trigger switch off by default.

CH1

REC

CAM
TRIGGER
COLOR-SYS

ON NTSC

AUTODIM

ON

SCREEN OFF

0

Tap ON to activate Trigger function. If trigger switch is turned on, the yellow icon will appear on display. To achieve trigger function, you also need to complete trigger wiring.

In Triggering status, MENU operation invalid, and the screen prompts TRIGGER LOCK.

CH1

REC

21

15 15

Touch screen invalid

For example, if you connect the camera to left turn signal light, the camera will automatically displayed on the monitor every time the left turn signal light turned on. Touch screen invalid during triggering. Once triggering released, touch screen be operational again.

22

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals