ggm gastro WAEBJ1 Waffle Maker User Manual
- June 6, 2024
- ggm gastro
Table of Contents
WAFFLE MAKER
USER’S MANUAL
Thank you for buying our product, in order to ensure safe use, please read the instructions before using it and keep it for reference.
| Model | Dimensions(mm) | Voltage（v） | Power （w） | Hz |
|---|---|---|---|---|
| WAEBJ1 | 440305225 | 230 | 2000 | 50-60 |
| WAEBJ2 | 630420225 | 230 | 2000+2000 | 50-60 |
Safety Precautions
The following safety precautions must be observed when using this product:
- Please read the relevant instructions carefully before using this product.
- Do not share the same power source with other high-power appliances to avoid excessive power load and other dangers.
- The surface temperature of this product is very hot after working or just Burns may be caused by contact with hot parts.
- If children are nearby, use the product with extra Do not leave the product to children alone.
- Do not allow this product to be used unattended.
- Do not touch the power cord with sharp objects and high-temperature surfaces to avoid damage to the power cord.
- Frequently check whether the power cord and plug are Once any signs of damage are found, please stop using immediately and ask for professional maintenance or replacement.
- After use, press the power button to close and pull out the plug from the socket to avoid leakage or shock due to aging insulation
- The product shall be installed in a dry, clean, and ventilated place; And put the product in a horizontal and smooth position
- For the sake of safety, the product must be reliable grounding and install a leakage switch to ensure personal safety, otherwise not to use.
- Please unplug the power cord and remove, check or clean the product after it has cooled completely.
- Do not plug or unplug the power cord in wet hands to avoid electric shock.
Note for the First Time Use
- Please read the instructions carefully.
- Please check if all switches are in the off position.
- Please check all the accessories are complete.
- Please tear up the protective film on the surface of the product, then clean the rust oil wipe on the surface of the product with a dry cloth.
- The supply voltage must match the voltage specified on this machine.
- The smoke is normal when the first time turns on the machine, it’s the oil inside the machine which to protect it become rusting.
Operating Steps
| |
---|---|---
1. Mix the ingredients.| 2. Turn on the switch, adjust the temperature to
160-180℃.| 3. Wait for the indicator light to go out.
| |
4. Put the pulp on the non-stick plate.| 5. Turn the machine and adjust the
timer to 3 minutes.| 6. Turn on the machine and take out the waffle.
Care and Cleaning
- Unplug the power cable and ensure that the product is cooled completely, then clean and collect.
- Cleaning the cooking surface with a soft cloth or sponge dampened in a mild detergent.
- Please don’t use a wire brush, stiff brush, or other corrosive liquids to clean it, avoiding damage to the surface coating.
- If batter adheres to plates, simply pour a little cooking oil onto the baked batter and let stand approximately S minutes, allowing the batter to soften for easy removal.
- Never use an abrasive cleanser or harsh pad.
- Never clean the product by sprinkling water and immersed in water.
Tips and Maintenance
- Pan MUST be open when pre-heating (if closed the temperature inside is much higher than open, long time high temperature is not good for Teflon coating), 160-180°C is our best temperature during the test.
- If the machine is an additional product to your shop, please keep the temperature under 80°C when no customers, it’s better to turn off the machine if there’s a long time no customer.
- If the machine is the main product in your shop, 3-4 units machine is suggested, they can be replaced every two hours.
- Use a bamboo stick to take out the cone, do not use any metal tool. If there are black dots appear on the pan surface, it can be judged that the caramel with Teflon coating is falling off (Caramel is when oil and sugar do not clean for a long time, it cannot be seen by visual inspection, it turns into black dots and stick on waffles) The best solution is changing heating pan.
- Use a wet towel to clean the pan, if anything is difficult to wipe off, use a professional kitchen glue brush, put some water in holes, heat the water a bit, it’s easier cleaning, but do not let the water go inside of the machine.
- Do not brush oil on the pan directly, you can add oil inside your recipe or waffle mix, but do not add too much oil, or it will get infiltrated and the heater may get burnt.
- Do not use a corrosive cleanser to clean the waffle pan.
This machine shell must be grounded and ensure safety, thank you for your cooperation.
Notice
The products whose electric power is over 1kw must plug a properly (grounded)
individual receptacle.| | | It could result in fire by ignition.
---|---|---|---
Do not cover the product with a cloth or plastic bag while you are using it.|
| | It could result in fire.
Ensure to unplug the product while you don’t use it.| | | It could result in
fire or electric shock.
Do not touch the product with wet hands.| | | It could result in electric
shock.
Never clean the machine by sprinkling water.| | | It could result in electric
shock or product damage.
Do not use the product outside in the rain or wet area.| | | It could result
in electric shock.
Use the product in a light place.| | | It could result in an accident or burn
if you use it in a dark room.
Do not use the product near flammable gas or Do not use the| | | It could
result in an explosion or fire.
Fault| Reason| Method
---|---|---
Turn on the power，but the green light doesn’t work| 1. There is no power at
the outlet
2. The power cord contacts bad terminal is loose
3. The green light was burnt out| 1. Check the socket for power
2. Fastening the power cord and terminals wiring
3. Replace the green light
The yellow light didn’t go out and the temperature of the machine rose is out
of control| 1. The thermostat doesn’t work| 1. Replace the thermostat
The indicator light is not on, but the temperature control is normal| 1. The
indicator light has bad contact
2. The indicator light was burnt out| 1. Fastening the wires
2. Replace the indicator light
The yellow light is on but not heated| 1. Wrong connection of indicator light
2. The heating tube was burnt out;| 1. Rewire according to correct wiring
2. Replace the heating tube
The green light is on, the yellow light is off, but the machine is not heated|
Thermostat was damaged| Replace the thermostat
The yellow indicator light is always on, the lower plate is not hot, the upper
plate has been heating, and the temperature is ultra-high| 1. The connection
of lower board heating pipes is loose
2. The lower heating tube is damaged| 1. Check the connection of heating
pipes
2. Replace the lower heating tube
The yellow light is on and the temperature of the lower plate is normal, but
the upper plate is not hot.| 1. The connection of upper heating pipes is
loose
2. The top heating tube is burnt out| 1. Check the connection of heating
wires
2. Replace the lower heating tube
Plugin the power and turn on the thermostat, then caused switch trip| 1. The
internal wiring is loose and the belt parts touch the metal shell;
2. Short circuit is caused by heating pipe burning| 1. Check the internal
wiring of the machine and tighten it
2. Replace with a new heating tube
Inspection of general faults
WAEBJ1
No.| Material no|
Spare parts name
---|---|---
1| | Up cover
2| | Handle fixed board
3| | Element pressboard
4| 3050035| Up element
5| 3040012| Connect terminal
6| 3080195| Flexible tube
7| 3040030| Wire clip
8| | Down cover
9| 3030002| Wire
10| | Base
11| 3040041| Foot
12| | Bottom sealing board
13| 3020031| 5-minute timer
14| 3020070| Timer knob
15| 3020053| Thermostat knob
16| 3020037| 300℃ dial
17| 3020002| 300℃ thermostat
18| 3091248| Support column
19| 3040001| Switch
20| 3040025| Light
21| 3050035| Down element
22| 3070383| Down molding board
23| 3070383| Up molding board
24| 3080380| Handle
WAEBJ2
No.
| Material no|
Spare parts name
---|---|---
1| | Up cover
2| | Handle fixed board
3| | Element pressboard
4| 3050035| Up element
5| 3040012| Connect terminal
6| 3080195| Flexible tube
7| 3040030| Wire clip
8| 3030002| Wire
9| 3040041| Foot
10| | Bottom board
11| 3040001| Switch
12| 3040025| Light
13| 3020002| Thermostat
14| 3020037| 300℃ dial
15| 3020053| Thermostat knob
16| 3020070| Timer knob
17| 3020031| 5-minute timer
18| 3050035| Down element
19| | Base
20| 3091248| Support column
21| | Down cover
22| 3070383| Down molding board
23| 3070383| Up molding board
24| 3080380| Handle
GGM Gastro International GmbH
Weinerpark 16, 48607 Ochtrup
www.ggmgastro.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>