FLASH F7300259 LED SPIDER MINI RGBW User Manual

FLASH F7300259 LED SPIDER MINI RGBW

Product Information

• SERIES: DJ
• LED SPIDER MINI RGBW
• EAN: [5905358808740]
• Art No: F7300259
• Light Source: 8x3W high power RGBW LEDs (R:2, G:2, W:2) Each LED singly controlled
• Power consumption: 24W (not including motor working)
• Voltage: AC 100V-240V 50-60Hz
• Strobe : 0-20Hz
• Control Mode: DMX512, Sound-activated, Master/Slave, Auto
• DMX Channels: 7CH/15CH
• Pack Size: H(17)xW(31)xD(19) cm

Product Usage Instructions:

1. Unpack and carefully check for any transportation damage before using the fixture.
2. Before operating, ensure that the voltage and frequency of the power supply match the power requirements of the fixture.
3. Ground the yellow/green conductor to earth to avoid electric shock.
4. Disconnect the main power before servicing and maintenance.
5. Use a safety chain when fixing the fixture. Do not handle the fixture by taking its head only, always take it by its base.
6. Repairs should be carried out by authorized technical assistance centers using the same type of spare parts.
7. Do not connect the device to any dimmer pack.
8. Do not touch any wire during operation to avoid the risk of electric shock.
9. Do not expose the fixture to rain or moisture to prevent the risk of electrical shock or fire.
10. Replace the housing if it is visibly damaged.
11. Do not look directly at the light spot while the fixture is on.

WARNING

• Use a clamp to rig the fixture.
• When clamping the fixture to a truss or other structure at any other angle than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
• Position or shade the bar so that the front lens will not be exposed to sunlight or any other strong light source from any angle – even for a few seconds. See Figure 1. The LED SPIDER lens can focus the sun’s rays, creating a potential fire hazard and causing damage.

IMPORTANT  Do not point strong light output from other fixtures at the LED SPIDER, as intense illumination can damage the display.

INTRODUCTION

THANK YOU FOR PURCHASING LED SPIDER. FOR SAFETY REASONS AND TO ENSURE TROUBLE- FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.

SAFETY INFORMATION

• Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.
• Unpack and check carefully there is no transportation damage before using the fixture.
• Before operating, ensure that the voltage and frequency of the power supply match the power requirements of the fixture.
• It’s important to ground the yellow/green conductor to earth to avoid electric shock.
• Disconnect main power before servicing and maintenance.
• Use a safety chain when fixing this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
• Maximum ambient temperature is: 40°C Don’t operate it where the temperature is higher than this.
• In the event of a serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself.
• Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type of spare parts.
• Do not connect the device to any dimmer pack.
• Do not touch any wire during operation and there might be a hazard of electric shock.
• To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
• The housing must be replaced if they are visibly damaged.
• Do not look directly at the light spot while the fixture is on.

PRODUCT INFORMATION

• Light Source: 8x3W high-power RGBW LEDs (R:2, G:2, W:2)
• Each LED singly controlled Power consumption: 24W (not including motor working)
• Voltage: AC 100V-240V 50-60Hz Strobe: 0-20Hz
• Control Mode: DMX512, Sound-activated, Master/Slave, Auto
• DMX Channels: 7CH/15CH Dimmer: 0-100% linear dimmer Beam angle: 4.5°
• Lighting angle: 120°
• Material: Iron and ABS
• Net Weight: 1,2 kg
• Weight with packaging: 1,6 kg Net Dimensions:
• H(14)xW(28)xD(14,5) cm Pack Size: H(17)xW(31)xD(19) cm

INSTALLATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and can support a weight of 10 times the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place that is out of the touch of people and has no one pass by or under it. The fixture may be installed in any orientation, but if installed horizontally with a downward beam angle, water can potentially pool in the fan wells. Under normal operation, the moisture will evaporate. However, in locations with high rainfall, you may wish to fabricate a rain shield above the fixture or modify the position and orientation of the fixture to minimize pooling. Two quarter-turn brackets are supplied with the fixture if it is to be flown above the ground. Rig the fixture to a support truss or structure using the supplied brackets and suitable clamps. Fasten a safety cable between the support structure and the attachment point on the fixture. The safety cable must be able to bear at least 10 times the weight of the fixture.

The package includes

• LED SPIDER (1 pc)
• Power cable type IEC C13 (1 pc)
• Mounting bracket and two screws
• User Manual (1 pc)

CONNECTION

The device is equipped with the following interfaces:

1. DMX (in/out): XLR 3(5)-pin socket
2. Power (in): IEC C13 socket

The connection is performed using a cable with XLR-female -> XLR-Male plugs.

CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between signal (-) and signal (+) into an XLR plug and plug it in the DMX output of the last fixture.

Diagram of connection of devices by DMX cable.

The connection is performed using a power cable with an IEC C13 connector (included). The device must be operated by qualified personnel.

CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only by the manufacturer or by a person with appropriate permissions
Using a lamp, the change rate of power voltage should be within ±10%, if the voltage is too high, it will shorten the light’s life. Voltage Specification.

Input Voltage: 100-250[V] AC
Frequency: 50/60[Hz] Total Power: 40[W]

Control Menu

1. On the fixture display, four buttons from left to right:
2. „MENU” button. It is the Function menu.
3. „Up” button. Modify data up.
4. „Down” button. Modify data down.
5. „ENTER” button. Save the modified data and exit the edit state.
6. In the editing state, if the „Enter” button is not pressed, the modified data will not be saved and will be lost after shutdown.

Display Function Menu

slow to fast
SoUd| ON, OFF| Sound control Switch
SoEn| 0-100| Sound Sensitivity (0 close, 100 the most)
teSt|  | Automatically Test
diSP| NO| Reverse display
 | YES| Forward display
Led| OFF| Background Light Switch
 | ON| Background Light Switch
tIL1| NO| Y1 Motor reverse
 | YES| Y1 Motor Forward
tIL2| NO| Y2 Motor reverse
 | YES| Y2 Motor reverse
dEFt| YES, NO| Reset

DMX CHART

Channel Mode

Channel Mode

FLASH-BUTRYM Sp.j.
Skarbimierzyce 18 · 72-002 Dołuje · POLAND
WWW.FLASH-BUTRYM.PL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>