August MR270-HD Dual Bluetooth Transmitter User Manual

August MR270-HD Dual Bluetooth Transmitter

Thank you for purchasing the August MR270-HD Dual Channel Bluetooth Transmitter.Thisuser manual is designed to familiarize you with all the features of this device. Please take the time to read this user manual carefully, even if you are already familiar with a similar product.

Safety

To ensure the safety of you and others, please read the Safety Instructions before using this device. Please do not disassemble the product, it can be unsafe and will invalidate the manufacturer’s warranty.

Disposal

Please ensure the product and accessories are disposed of in compliance with the WEEE (Waste Electrical and Electronic Equipment) Directive and any other regulations applicable to your country. Always check with the environment agency and any other relevant authorities for current disposal regulations .

Declaration of Conformity

The Declaration of Conformity can be found on our website at http://augustint.com/en/declaration/

Customer Service

You can contact us by phone on : +44 (0)845 250 0586 or by email at: service@augustint.com should you require further technical support or customer service.

Safety Instructions

1. Do not use this device near water
2. Clean only with a dry cloth. Switch this product off before cleaning.
3. Do not install near any heat sources such as stoves or other apparatus that produce heat.
4. Only use the accessories supplied by the manufacturer.
5. Do not open the device, as this will invalidate the warranty.

Main Features

• Transmits Audio to Two Devices Simultaneously
• Optical and 3.5mm Audio Input
• Built-in Long Life Rechargeable Battery
• Distance: up to 10m (Class II)
• Bluetooth Profiles: A2DP, AVRCP, PBAP

Box Contents

Part Names and Functions

1. Button I
2. Status LED I
3. Button II
4. Status LED II
5. Optical Audio In
6. Aux In
7. Charging LED
8. Charging Port
9. ResetButton 5 6 7 8 9 10 1 O.Power Button

Status LED Meaning

(1) When connecting two devices to the MR270-HD at the same time, the device will support aptX.
(2) Due to the LED used, the constant yellow light may be mistaken for green.

Operations

Setup

Note: When both optical and aux audio input are connected , the MR270-HDwill use the aux audio input.

Bluetooth Connection

Press and hold the power button to switch the MR270-HDon.
Both status LEDs will light white and the MR270-HD will search for paired devices to connect to.

 Connecting a Device

1. Press button I or button II to enter paring mode. In paring mode the status LED will flash blue quickly.
2. Enable Bluetooth on the receiving device and enter pairing mode (see the device’s user manual for more information).
3. The MR270-HD will connect automatically to the receiving device. Once successfully paired, status LED I or II will light blue, green, yellow or red constantly mode (see 4.1 Status LED Meaning for more information).

• Clearing Bluetooth Connections Press and hold button II for 5 seconds to clear all paired devices from the MR270-HD.

Charging and Power Saving

Charging the Device

The status LEDs will flash white when the battery is low.
To recharge, connect the MR270-HD to a power USB port using the provided USB power cable.

Whilst charging, the charging LED will light red and turn green once the battery is fully charged .

A full charge takes approximatively 1.5 hours depending on power input.

Note: When powered by a USB cable the MR270-HD will switch on automatically.

Power Saving

When the transmitter is switched on and powered
by the battery, but no Bluetooth connection is Iavailable, or no devices are connected, the MR270-HDwill switch off automatically after 30 minutes.

Enable/ disable aptX

If your headphones don’t support aptX, please switch Enable/  Disable button on MR270-HD.
Remove the USB cable, tum on the device, press Button I for 10 seconds to switch between Enable/Disable:

1. When aptX is enabled, press Button I for 10 seconds to disable aptX, the white indicator light turns off.
2. When aptx is disabled, press Button I for 10 seconds to enable aptX, the white indicator light will flash three times then tum off. After aptX switch, press power button twice to tum on device.

Specifications

Troubleshooting

• Fully charge the MR270-HD
• Turn on power switch

Unable to pair Bluetooth audio device|

• Confirm that the MR270-HD is in pairing mode. device
• Confirm that the MR270-HD is within 1 Om of the audio device.
• Press and hold button II for 5 seconds to reset the Bluetooth connection

There is no sound from my Bluetooth audio device|

• Make sure the device is connecting to the Bluetooth audio MR270-HD via Bluetooth. device
• Make sure the cable is connected between your source device and the MR270-HD.
• Check the volume on both source device and your Bluetooth audio device.

Warranty

This product is guaranteed for twelve months Ifrom the date of the original purchase. In the  unlikely event of any defect arising due to faulty materials or workmanship, the unit will be either replaced or repaired free of charge (where possible) during this period . An alternative product will be offered in case the product is no longer available or repairable.

This warranty is subject to the following conditions :

• The warranty is only valid within the country where the product is purchased .
• The product must be correctly installed and operated in accordance to the instructions given in this user manual.
• The product must be used solely for domestic purposes.
• The warranty only covers the main unit, and does not cover the accessories.
• The warranty does not cover the damage caused by misuse, negligence, accident and natural disaster.
• The warranty will be rendered invalid if the product is resold or has been damaged by inexpert repairs . The manufactures disclaim any liability for incidental or consequential damages.
• Please consult our customer adviser before returning any product; we are not responsible for any unexpected product returns .
• Any faulty product must be kept and returned in the original packaging with all the accessories and the original copy of the purchase receipt.

The warranty is in addition to, and does not diminish, your statutory or legal rights .

Customer Service:
Telephone: +44 (0) 845 250 0586
Email : service@augustint.com

This product is in compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU. The Declaration of conformity
may be consulted online at http://www.augustint.com/en/declaration

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules . These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation . If this equipment does cause harmful interference to radio or television reception , which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>