teesa TSA0515 Rotary Shaver Owner’s Manual

: June 6, 2024
: teesa

Table of Contents

teesa TSA0515 Rotary Shaver Owner’s
OVERVIEW
SAFETY INSTRUCTIONS
CHARGING
LED indicators
OPERATION
CLEANING
STORAGE
REPLACING SHAVING HEAD
SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

teesa TSA0515 Rotary Shaver Owner’s

OVERVIEW

teesa TSA0515 Rotary Shaver Owner's 1

Shaving head
Retaining frame
Retaining frame lock
Shaving head release button
Power button
LED indicators
Trimmer release slide
MicroUSB port (charging)

SAFETY INSTRUCTIONS

In order to reduce the risk of any injury, follow basic safety precautions applied when using any electrical device, including the following:

Read this instruction manual carefully, even if you are familiar with the appliance.
Before connecting the device to power supply socket, make sure the voltage indicated on the appliance corresponds to the voltage in the power supply socket.
ALWAYS turn off the device and disconnect it from the mains supply:
if it’s not operating correctly,
if there’s an uncommon voice when using,
before disassembling the device,
before cleaning,
before servicing.
When you disconnect the power cord, grasp and pull the plug, not the cord/cable.
This appliance may be used by children and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided by a person who is responsible for their safety in a cautious manner, and all the safety precautions are understood and followed. Children should not play with this device.
Use only the included AC charger to charge the device.
Do not use this appliance if it’s not operating properly or has been dropped into water. Do not attempt to repair this appliance yourself, only authorized and qualified personnel may repair this device. This product has no user serviceable parts.
Keep the device and its cord/cable away from heat, water, moisture, sharp edges and any other factor which may damage the appliance or its cord.
Do not use the product for purposes/uses different from what displayed in this operating manual.
Producer of this product is not responsible for damages caused by inappropriate handling and using of the device.
Use only original/authorized accessories.
The device is suitable to be used under the shower or in the bath.
Do not place or store product where it can fall or be pulled onto a tub or sink.
Do not reach for a product that has fallen into water. Unplug it from power supply socket immediately.
Do not handle the appliance with wet hands when it is connected to power supply.
Do not immerse the appliance in water or any other liquids.
Product for household use only. Not for commercial use.
Clean and store this appliance in accordance to instructions listed in “Cleaning” and “Storage” section.
This product is water-resistant based on the IPX7 rating, which tests submersion up to 1 meter for up to 30 minutes. Despite this classification, your device is not impervious to water damage in any situation. The device is electrically safe and is designed for use in the bathroom- it is suitable for cleaning under running water but it is not meant to be used underneath the water.

CHARGING

Connect one end of the microUSB cable with the microUSB port of the device.
Connect the other end to the power supply socket.
When charging has finished, disconnect the AC adapter from power supply and the device.

Notes

It takes about 60 minutes to fully charge the device what provides about 120 minutes of shaving time.

LED indicators

During charging, all LED indicators flash alternately.
When the battery level is lower than 10%, first LED indicator flashes red. It indicates that the device must be charged.
When the battery level reaches 10%, red light turns white and flashes.
When the battery level reaches 20%, first indicator stops flashing and lights white while the second one starts flashing.
When the battery is fully charged, all five LED indicators light white.

OPERATION

Shaving

Press power button to turn on the shaver.
Move the shaving head against the direction of beard growth using both circular and straight movements.
Gently press shaver to the skin, so the floating blades can easily follow the contours of your face.
After shaving turn off the appliance by pressing power button.
Clean the shaver according to the instructions included in “Cleaning” section.
Put the protective cap on the shaving head to protect the blades from any damage.

Note

The device is water-resistant, therefore it can be also used on wet skin.
It is also possible to use the shaver together with the shaving foam.
Your skin may need 2 or 3 weeks to get accustomed to the new shaving system.

Trimming

Push the trimmer release slide downwards to open the trimmer.
Turn on the appliance.
Start trimming.
After trimming, press power button to turn off the appliance.
Clean the trimmer according to the instructions included in “Cleaning” section.
Push the trimmer downwards until it locks in place to close it.

CLEANING

General

Do not immerse the appliance in water.
Do not use any abrasives or chemical agents to clean this product.
Clean only the casing with a soft and slightly damp cloth.
Do not clean the shaving head, blades or hair chamber with a cloth, towel or tissue as this may damage the shaving blades.
Clean the appliance after each use. Regular cleaning guarantees better shaving performance.
After using the appliance with shaving foam, please rinse the shaving head under warm running water to clean away any excess foam and dirt.

Cleaning with cleaning brush

Make sure the appliance is turned off and disconnected from power supply.
Clean the outside of the shaving head by brushing out dirt.
Press shaving head release button to open shaving head.
Clean the inside of the shaving head and hair chamber.
After cleaning close the shaving head by pushing it downwards until it locks in place.

Cleaning trimmer

Make sure the appliance is turned off and disconnected from power supply.
Push the trimmer release slide downwards to open the trimmer.
Brush up and down along the trimmer teeth.
After cleaning, push the trimmer downwards until it locks in place to close it.

Thorough cleaning

Note : Clean the shaving blades thoroughly once a month to provide optimal performance.

|

1. Make sure the appliance is turned off and disconnected from power supply.

2. Press the shaving head release button to open the shaving head.

---|---
|

3. Pull the shaving head off the appliance.

---|---
|

4. Turn the retaining frame lock counterclockwise and remove the retaining frame.

|

5. Remove and clean the shaving blade and its guard one by one. Note: Do not clean more than one blade and guard at a time, since they are all matching sets. Shaving performance may deteriorate if blade will be placed in the wrong guard.

|

6. Remove the blade from the guard and clean it with the included brush.

Note: Exercise caution while cleaning the blades as they are sharp!

7. Clean the guard with the brush.

|

8. Put the blade back into the guard.

9. Put the blade back into the corresponding blade holder in the shaving head.

|

Note: Make sure the notches on both sides of the shaving blades fit exactly onto the notches in the shaving blade holder.

| ****

10. Put the retaining frame back into the shaving head and turn the retaining frame lock clockwise.

| ****

11. Insert the lug of the shaving head into the slot in the top of the appliance.

12. Close the shaving head.

Note: If the shaving head does not close smoothly, check if you have inserted the shaving blades properly and if the retaining frame is locked.

STORAGE

Before storing the appliance, make sure it is clean, dry and disconnected from the power supply.
Store the appliance in a dry, cool place, out of the reach of children.
Store the appliance with the protective cap assembled to prevent damage to the blades.

REPLACING SHAVING HEAD

Notes

It is recommended to replace shaving head every 18 months.
Replace damaged shaving blades immediately.
Always replace the shaving head with the original Teesa shaving head (TSA0073).
Shaving head is available to be bought from the online store Teesa.pl or lpelektronik.com.

Make sure the appliance is turned off and disconnected from power supply.
Press the shaving head release button to open the shaving head.
Pull the shaving head off the appliance.
Insert the lug of the new shaving head into the slot in the top of the appliance. Close the shaving head.
Note: If the shaving head does not close smoothly, check if you have inserted the shaving blades properly and if the retaining frame is locked.

SPECIFICATIONS

Main features
Three floating blades adjusting to all face shapes Built-in pop-up trimmer perfect for trimming sideburns and moustache High-quality steel bladesProtection against beard pulling when low battery Wet and dry usage Five LED battery indicators Cord and cordless use Quiet operationEasy to clean Ergonomic design Anti-slip gripTechnical data Power: 8 W Protection class: IPX7

Rotation speed : 2200 – 2800 rpm
Run time : up to 120 min
Charging time : up to 60 min
microUSB port (charging)
Battery : 3,7 V / 800 mAh
Power supply: 100 ~ 240 V; 50/60 Hz
In set AC charger, protective cap, cleaning brush, travel pouch, user manual Physical parameters
Weight : 154,5 g
Dimensions : 59,7 x 153 x 55,8 mm

(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k., ul. Garwolińska 1, 08-400 Miętne.