SALUS RT510SPE Wireless Electronic Weekly Temperature Controller Installation Guide
- June 6, 2024
- SALUS
Table of Contents
- Introduction
- Product Compliance
- Safety Information
- Button Functions
- LCD icons
- DIP switch settings
- Smart plug LED indication
- Installation – Step 1
- Installation – Step 2
- Thermostat pairing process
- Test the pairing process
- Setting hour and day
- Temporary override
- Permanent override
- Setting programs
- Installer mode
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
RT510SPE
Installation Guide
Introduction
The RT510SPE module will switch your appliance on or off in accordance with the temperature set by you. The completed RT510SPE series consists of a transmitter – RT510TX thermostat and a Smart Plug SPE868. Go to www.salus- manuals.com for the full PDF version of the manual.
Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU, and
RoHS 2011/65/EU. Full text of the EU
Declaration of Conformity on www.saluslegal.com
868.0-868.6MHz; <13dBm
Safety Information
Use in accordance with the regulations. Indoor use only. Keep your equipment completely dry. Disconnect your equipment before cleaning it with a dry towel.
Button Functions
- Press for frost mode
- Press 3 sec for holiday mode
- Increase button
- Decrease button
- Press to confirm setting
- Press to select setting
- Press to enter/exit permanent override
- Press to enter/exit boost mode
LCD icons
- Current day of the program
- Current time
- Current Temperature
- Temperature unit
- Frost Protection
- Vacation Mode
- Temporary/Permanent Override
- Heating Mode ON
- RF signal
- Low battery
- Program number
- Boost Mode
DIP switch settings
The DIP Switches can be found on the rear of your thermostat.
| Control feature | TPI | Span |
|---|---|---|
| Operation | When TPI is selected on DIP switch № 2, the DIP switch № 1 is |
functional. You can choose the Cycles Per Hour between a lower comfort level (6CPH) and a higher comfort level (9CPH).| When Span is selected on DIP switch № 2, the DIP switch № 1 is not functional. The temperature accuracy of your thermostat is set to ± 0.25 °C.
Smart plug LED indication
| Solid Red – paired, a smart plug is off
---|---
| Solid Green – paired, a smart plug is on
| 1. Pulsating red- waiting for pairing
2. Slow Flash red – overheat protection
3. Flashing red – safe mode, lost connection with thermostat and smart plug
is off
| Flashing Green – in test pairing mode
| Flashing Red and Green -fail-safe mode, lost connection with thermostat, a
smart plug is on
If the thermostat loses connection with the Smart Plug, the Smart Plug goes into fail-safe mode after 22 minutes. In this mode, you still can operate your Smart Plug manually (by pressing the button on the device).
Installation – Step 1
The thermostat and the smart plug are pre-paired from the factory if purchased as a pack. If not, follow the thermostat pairing process.
Installation – Step 2
Thermostat pairing process
In case you have more than 1 smart plug, set ALL the smart plugs into pairing
mode and start the pairing process. The LED will flash red when the plug is in
pairing mode.
Put the thermostat into pairing mode, by pressing the pair button for 3
seconds. After the smart plug is paired with the thermostat, the LED is steady
red.
Begin pairing process
End pairing process
Test the pairing process
Setting hour and day
Continue with the same steps for setting the Day. Press Set to return to the Main Screen.
Temporary override
Permanent override
Setting programs
You can create personalized programs for your controller. You have the option to choose between a 5-2 days program or a daily one by using parameter d04 from Installer mode.
Press SET to change your programs
Use ∧and ∨to select Weekend/Weekday, press to confirm your option. Follow the same steps for setting the hour, minutes, and temperature. After you have done all the changes, please press SET to confirm all your choices and to return to the Main Screen. SELECT
Installer mode
Press the three buttons together for 3 seconds. Use to select dxx parameter, ∧or ∨to change +Hr parameter value and to confirm.
Parameter
| dxx | Function | Parameter | Default value |
|---|---|---|---|
| d01 | Temperature display increments | 0.1 or 0.5°C | 0.5°C |
| d02 | Temperature offset | +/-3.0°C | 0.0°C |
| d03 | Frost setpoint | 5.0-17.0°C | 5.0°C |
| d04 | Programmer selection | 5/2 or 24 hr (7d) | 52d |
FR/ NL / DE:
support@salus-controls.de
tel: +49 6108 8258515
Head Office:
SALUS Controls Plc
Units 8-10 Northfield Business Park
Forge Way, Parkgate, Rotherham
S60 1SD, United Kingdom
T: +44 (0) 1226 323961
E: sales@salus-tech.com
E: techsupport@salus-tech.com
www.salus-controls.com
SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development SALUS Controls plc
reserve
the right to change specification, design, and materials of products listed in
this brochure
without prior notice.
For PDF Installation guide please go towww.salus-manuals.com
Issue date: 2020 V
06/2020 V024
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>