robustel R5020 5G WiFi Wireless Router Owner’s Manual
- October 27, 2023
- robustel
Table of Contents
R5020
Hardware Manual
Version: 1.0.0
Date: July 6, 2022
Robustel R5020 Hardware Manual
Regulatory and Type Approval Information
Table 1: Toxic or Hazardous Substances or Elements with Defined Concentration Limits
Name of
the Part| Hazardous Substances
---|---
(pb)| (Hg)| (Cd)| (Cr(VI))| (PBB)| (PBDE)| (DEHP)| (BBP)| (DBP)| (DIBP)
Metal| | | | | | | | | |
parts| o| 0| 0| 0| –| | | –| –| –
Circuit| | | | | | | | | |
modules| o| 0| 0| 0| 0| 0| 0| 0| 0| 0
Cables
and cable| | | | | | | | | |
assemblie s| o| o| 0| 0| 0| 0| 0| 0| 0| 0
Plastic and| | | | | | | | | |
polymeric parts| o| 0| 0| 0| 0| 0| 0| 0| 0| 0
o: Indicates that this toxic or hazardous substance contained in all of the
homogeneous materials for this part is below the limit requirement in RoHS2.0.
X: Indicates that this toxic or hazardous substance contained in at least one
of the homogeneous materials for this part might exceed the limit requirement
in RoHS2.0.
-: Indicates that it does not contain the toxic or hazardous substance.
Radio Specifications
RF technologies | 3G, 4G, 5G, GNSS*, Wi-Fi |
---|---|
Cellular Frequency* | 3G: WCDMA: B1/B2/B3/B4/B5/B6/B8/B19 |
4G: LTE FDD: B1/B2/B3/B4/B5/B7/B8/B12(B17)/B13/B14/
B18/B19/B20/B25/B26/B28/B29/B30/B32/B66/B71 LTE TDD:
B34/B38/B39/B40/B41/B42/B43/B48
LAA: B46
5G: NSA/SA: nl/n2/n3/n5/n7/n8/n12/n20/n25/n28/n38/n40/
n41/n48*/n66/n71/n77/n78/n79
Wi-Fi Frequency| 2.4 GHz: 2.412 – 2.472 GHz 5 GHz: 5.15 – 5.825 GHz
Max RE power| 28 dBm@5G, 25 dBm@WCDMA, 28 dBm@LTE, 22.96dBm@Wi-Fi
- May vary on difference models.
Simplified EU Declaration of Conformity
We, Guangzhou Robustel Co., Ltd. are located at 501, Building #2, 63 Yongan
Road, Huangpu District, Guangzhou, China, declare that this radio equipment
complies with all applicable EU directives. The full text of the EU DoC is
available at the following internet address:
www.robustel.com/certifications/
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
IC Declaration of Conformity
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radio Frequency Exposure Statement for IC
This device complies with IC exposure limits set forth for an uncontrolled
environment. This device shall be installed and operated with minimum distance
20cm between the radiator & body.
Related download link
Find more product documents or tools at:
www.robustel.com/en/documentations/
Technical Support
Tel: +86-20-82321505
Email: support@robustel.com
Web: www.robustel.com
Document History
Updates between document versions are cumulative. Therefore, the latest document version contains all updates made to previous versions.
Date| Firmware Version| Document Version| Change
Description
---|---|---|---
6-Jul-22| 5.0.0| 1.0.0| Initial release.
| | |
| | |
| | |
| | |
| | |
| | |
| | |
Overview
Robustel R5020 supports WCDMA 3G network, LTE 4G network, and 5G network to provide high-speed wireless network bandwidth for devices through wireless connection, and it has dual-SIM card backup to ensure stable wireless network connection.
Package Checklist
Before commencing installation ensure your package has the following components:
Note: The accessories could be different on specific order.
Panel Layout (May Vary on Different Models)
Interface Descriptions
- Power Supply. 3PIN 3.5mm pitch terminal block.
PIN| Description| Note|
---|---|---|---
1| V+| Connect adapter or battery positive (red line)| Note:
- ACC and POE function can only be selected one
- The input voltage is 10 to 30V DC(With ignition
sensing) or 9 to 36V DC(Without ignition sensing)
2| V-| Connect adapter or battery negative (yellow line)
3| ACC (Optional)| Car ignition and flameout detection (green line)
Note: when the car ignition and flameout detection function
is not used, the ACC pin need to be connected to the V+ andcannot be left floating.
- LED Indicator.
Name| Color| Status| Description
---|---|---|---
RUN| Green| On, solid| Router is powered on
On, blinking| Router starts operating
Off| Router is powered off
MODEM| Green| On, solid| Link connection is working
On, blinking| Data is sent and received
Off| Link connection is not working
NET| Green| On, solid| Connection to 5G network is established(5g signal is the best)
On, blinking| Connection to Legacy network (4G or 3G) is established(3G signal difference / 4G signal medium)
Off| Network is not joined or joining
USR-OpenVPN| Green| On, solid| OpenVPN connection is established
Off| OpenVPN connection is not established
USR-IPsec| Green| On, solid| IPsec connection is established
Off| IPsec connection is not established
USR-SIM| Green| On, solid| Main SIM card is being used
On, blinking| Backup SIM card is being used
Off| No SIM card is being used
| Green| On, solid| 5G network: Reference Signal Received Power greater than -86 dBm (Strong signal) Non-5G network: Received Signal Strength Indication greater than -73 dBm (Strong signal)
Yellow| On, solid| 5G network: Reference Signal Received Power -105 to -86 dBm (Moderate signal) Non-5G network: Received Signal Strength Indication -91 to -73 dBm (Moderate signal)
Red| On, solid| 5G network: Reference Signal Received Power -140 to -106 dBm (Weak signal) Non-5G network: Received Signal Strength Indication -111 to -93dBm (Weak signal)
—| Off| No signal
WiFi| Green| On, solid| Wi-Fi is enabled and working properly
Off| Wi-Fi is disabled or not working properly
Note: You can choose the display type of USR LED. For more details,
please refer to
RT123_SM_RobustOS Software Manual, Services > Advanced > System >System
Settings > User LED Type.
- Reset Button.
Function| Operation
---|---
Reboot| Press and hold the RST button for 2′ 5 seconds under the operating status.
Restore to default configuration| Press and hold the RST button for 5-10 seconds, the RUN LED starts blinking quickly, the router will restore to default configuration.
Restore to factory default settings| Once the operation of restoring default configuration is performed twice within one minute, the router will restore to factory default settings.
Note: The more details please refer to RT123 SM RobustOS Software Manual, 2.3 Factory Reset. - Ethernet Ports. There are four Ethernet ports on R5020, including ETH0 (Optional POE supported), ETH1, ETH2, ETH3. The ETH0 on the router can be configured as a WAN port, while ETH1, ETH2 and ETH3 can only be configured as a LAN port. By default, ETH1, ETH2 and ETH3 are lan0, and their IP are 192.168.0.1/255.255.255.0.
Ethernet LED Indicator| Status| Description
---|---|---
Link indicator (Yellow)| On, solid| Connection is established
On, blinking| Data is being transferred
Off| Connection is not established - Digital IO & Serial Port. 2x5PIN 3.5mm pitch terminal block, 1 set of DO, 1 set of DI, 1 x RS232 and 1 x RS485.
DI signal access, can be used for NPN/PNP type sensor signal or switch signal acquisition. DO signal output, can be used for NPN/PNP sensor control, please connect signals by referring to typical applications .
PIN| DI/DO| RS232| RS485| Direction|
---|---|---|---|---|---
1| IGND| —| —| —|
2| OGND| —| —| —
3| —| TXD| —| Router → Device
4| —| RXD| —| Router ← Device
5| —| GND| —| —
6| IN| —| —| —
7| OUT| —| —| —
8| —| —| A| —
9| —| —| B| —
10| —| —| GND| —
Typical Application:
Note: The external power
supply DC voltage range is 3V~30V.
- USB Interface.**
Function| Operation**
---|---
Firmware upgrade| USB interface is used for batch firmware upgrading, but cannot be used for sending or receiving data from slave devices which connected to it. You can insert a USB storage device into the router’s USB interface, such as a U disk or a hard disk. If there have a supported configuration file or a router firmware in this USB storage device, the router will automatically update the configuration file or the firmware. For more details, please refer to RT123_SM_RobustOS Software Manual.
Hardware Installation
- SIM Card Installation. Remove the SIM card cover to insert the SIM cards into the device, then screw up the cover.
- Antenna Installation. Rotate the antenna into the antenna connector accordingly. Here take the cellular antenna as example. For 5G 4-IN-1 combo antenna, LHM# cable need to be connected to ANT1 and ANT2 while the MH# cable need to be connected to ANT0 and ANT3. GPS function is available when using the 4 in 1 combo antenna.
- Terminal Block Installation. Insert the 2x5PIN terminal blocks into the interfaces connector, then can connect the devices or sensors to the gateway via corresponding interfaces e.g. RS232/RS485, DIDO…
- Mounting Kit installation.
- Grounding the Device. Grounding will help to prevent the noise effect due to electromagnetic interference (EMI). Connect the device to the site ground wire by the grounding screw before powering on.
- Power Supply installation. Insert the power supply cord into the corresponding terminal block if needed, then insert the terminal block into the power connector.
- Connect the router to the computer. Connect the Ethernet cable to any port labeled ETH0 to ETH3 on the bottom of the router, and connect the other end of the cable to your computer.
Login to the Device
- Connect the router’s Ethernet port to a PC with a standard Ethernet cable.
- Before logging in, manually configure the PC with a static IP address on the same subnet as the gateway address, click and configure “Use the following IP address”.
- To enter the gateway’s web interface, type http://192.168.0.1 into the URL field of your Internet browser.
- Use login information shown in the product label when prompted for authentication.
- After logging in, the home page of the web interface is displayed, then you can view system information and perform configuration on the device.
- The automatic APN selection is ON by default, if need to specify your own APN, please go to the menu Interface->Link Manager->Link Setting->WWAN Settings to finish the specific setting.
- The more configuration details please refer to RT123_SM_RobustOS Software Manual.
Support: support@robustel.com
Website: www.robustel.com
©2022 Guangzhou Robustel Co., Ltd.
All rights reserved. Subject to change without notice.
References
- 4G/LTE/5G/Cellular Routers, Gateways and Modems for Industrial IoT - Robustel
- 4G/LTE/5G/Cellular Routers, Gateways and Modems for Industrial IoT - Robustel
- Certifications | Robustel - Industry-leading IoT Solutions Provide
- Robustel Cloud Manager Service
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>