Vantrue 11.5ft Type C USB 12V 24V to 5V Dash Cam Hardwire Kit with Mini-Complete Features/Instruction Guide

Vantrue 11.5ft Type C USB 12V 24V to 5V Dash Cam Hardwire Kit with Mini

Specifications

• DIMENSIONS : 4.45 x 2.91 x 1.93 inches
• WEIGHT : 5.3 ounces
• INPUT VOLTAGE: DC 12V-24V
• OUTPUT CURRENT: DC 5V
• OUTPUT CURRENT: 5A
• CABLE LENGTH: 5 FT
• BRAND: Vantrue

Introduction

The Vantrue hardwire kit is compatible with 12 and 24V vehicles. It connects the camera to the car, truck, bus, SUVs or big roof. It provides constant power by directly connecting to the battery. The hardwire kit comes with a switch button that can be used to ACC mode, which means it can turn on and off with the ignition, without requiring to plug in the charger. Another important feature is that it has a smart low voltage protection for your camera, so if the supply to your vehicle’s camera drops below 11.6V it shuts it off automatically. It is compatible with multiple devices using the type C USB plug.

Product view

1. Type C USB Dash Cam Hardwire Kit
2. Mini/LP ACN Add-A- Circuit Fuse Holder
3. Mini ACS Add-A-Circuit Fuse Holder
4. ATO ACU Add-A-Circuit Fuse Holder
5. Micro2 Add-A-Circuit Fuse Holder
6. Red Wire to Fuse Box
7. Black Wire to the Ground

Installation

You can just check the installation video at product details page or via this YouTube link:

https://www.youtube.com/watch?v=v37kMMnbGDI

Please note : This video was done using a previous version of the hardware kit. This new version includes 4 Add a Circuits and there is no need to purchase it separately.

Locate your fuse box
Use your owner’s manual to identify the location of the internal fuse box. This is normally found by the footwell on the driver’s side of your vehicle. You may need a tool to gain access.

Find the correct fuse slot for your hardwire kit
Next you need to find the fuse map which is a diagram describing what each fuse does and where it’s located in the box. This simplifies the process and ensures you don’t pull the airbag fuse. Or you will need a circuit tester or multimeter to test if a fuse is ignition switched or always on.

If you need to find an ignition switched fuse, put the key in the vehicle, find the fuse which is not lit up while the car is off, and test it by turning the car on to see if it lights up. If your kit requires constant power, turn off the car and remove the key to see which fuse slots stays lit on.

Identify your fuse type
Next you need to identify the type of fuse as depicted above.

Connect to car fuse box

1. Once you’ve determined which fuse slots you need to use for your hardwiring kit you can crimp the red wire of your hardwire kit onto the Add-A-Fuse.

2. Make sure the key has been removed from the ignition. Using a fuse puller or a pair of pliers, gently remove the fuse you identified.

3. Install the fuse you just removed into the installation kit add-a-fuse circuit.

4. Plug the add-a-circuit into the fuse box in the correct orientation.

Ground the hardwiring kit
Next, slip the black wire (which is in the shape of a C) under a metal bolt or screw in your vehicle (this is the ground wire).  Using a multimeter, check that it is not attached onto plastic parts.  You will typically need a socket wrench to loosen the nut or bolt that you choose to ground with. To attach the grounding terminal, loosen the nut or bolt enough to slip it in and tighten it back up afterward. A lose of ground can result in power issues for your dashcam.

Test your installation
Connect the dashcam with the hardwire kit. If everything was installed correctly, you should see your dashcam turn on and begin recording! At this point you may go ahead and reinstall all interior panels that were removed to facilitate running the power cable.

Warranty & Support

The Vantrue dash cam hardwire kit comes with a full 12 months warranty. If you register your product on our official site (www.vantrue.net/register), you can extend the warranty to 18 months.

If you have any questions regarding your product, please do not hesitate to contact us at support@vantrue.net, or drop us a message through the live chat box at www.vantrue.net. Queries are typically answered within 12-24 hours.

Your opinion matters

VENTURE is firmly committed to always improving our products, services, and user experience. If you have any thoughts on how we can do even better, we welcome your constructive feedback and suggestions. Connect with us today at support@vantrue.net

FREQUENTLY ASKED QUESTIONS

• Can anyone tell me the wire length. (Both sides of the control box)?
  The length of the wire is approximately 11.5m

• Does this work for hybrid vehicles?
  Yes, it works for hybrid vehicles

• What amp fuse is this?
  5 amp

• Does this provide enough power for the N4 with GPS module?
  Yes, it does.

• Will this work for the T3 model?
  Yes, it will work for T3 model.

• Can this work with Lexus UX250H?
  Yes, it can work with Lexus UX250H

• Why doesn’t Vantrue have fuses with the hardwire kits ?
  The hardwire kits have fuses.

• The camera work as GPS too?
  No, the camera itself doesn’t work as GPS.

• Will it work on the Viofo A139?
  Yes, it will with Viofo A139.

• Is this compatible with the Vantrue X3 1440P?
  No, it is not compatible with Vantrue X3 1440P.

https://vantrue.net/Support/detail/id/138.html

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>