robustel R1510 4G LTE Router User Manual

May 15, 2024
robustel

robustel R1510 4G LTE Router

robustel R1510 4G LTE Router

Regulatory and Type Approval Information

Table 1: Toxic or Hazardous Substances or Elements with Defined Concentration Limits

Name of the Part|

Hazardous Substances

---|---
(Pb)| (Hg)| (Cd)| (Cr(VI))| (PBB)| (PBDE)| (DEHP)| (BBP)| (DBP)| (DIBP)
Metal

parts

| o| o| o| o| –| –| –| –| –| –
Circuit

modules

| o| o| o| o| o| o| o| o| o| o
Cables and cable assemblies| o| o| o| o| o| o| o| o| o| o
Plastic and polymeric parts| o| o| o| o| o| o| o| o| o| o
o:
Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in RoHS2.0.X:
Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials for this part might exceed the limit requirement in RoHS2.0.

-:
Indicates that it does not contain the toxic or hazardous substance.

Radio Specifications

RF technologies 2G, 3G, 4G, Wi-Fi
Cellular Frequency* 2G : GSM: B3/B8

3G : WCDMA: B1/B8
4G : LTE FDD: B1/B3/B7/B8/B20/B28A
Max RF power| 33 dBm±2dB@2G, 24 dBm+1/-3dB@WCDMA, 23 dBm±2 dBm@LTE, 18 dBm@Wi- Fi

* May vary on difference models.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s) and Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC& IC Radiation Exposure Statement

This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Simplified EU Declaration of Conformity

We, Guangzhou Robustel Co., Ltd. are located at 501, Building #2, 63 Yongan Road, Huangpu District, Guangzhou, China, declare that this radio equipment complies with all applicable EU directives. The full text of the EU DoC is available at the following internet address: www.robustel.com/certifications/

Safety Information

General

  • The router generates radio frequency (RF) power. When using the router, care must be taken on safety issues related to RF interference as well as regulations of RF equipment.
  • Do not use your router in aircraft, hospitals, petrol stations or in places where using cellular products is prohibited.
  • Be sure that the router will not be interfering with nearby equipment. For example: pacemakers or medical equipment. The antenna of the router should be away from computers, office equipment, home appliance, etc.
  • An external antenna must be connected to the router for proper operation. Only uses approved antenna with the router. Please contact authorized distributor on finding an approved antenna.

RF Exposure

  • This device meets the official requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by authorized agencies.
  • The device must be used with a minimum separation of 20 cm from a person’s body to ensure compliance with RF exposure guidelines. Failure to observe these instructions could result in your RF exposure exceeding the applicable limits.

Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Router may be used at this time.

The symbol indicates that the product should not be mixed with general household waste but must be sent to separate collection facilities for recovery and recycling.

The symbol indicates that the product meets the requirements of the applicable EU directives.

Symbol The symbol indicates that the product meets the requirements of the relevant UK legislation.

Document History

Updates between document versions are cumulative. Therefore, the latest document version contains all updates made to previous versions.

Date| Firmware Version| Document Version| Change Description
---|---|---|---
July 6, 2022| 5.0.0| 1.0.0| Initial release.
Nov. 23, 2022| 5.0.0| 1.0.1| Added declaration for product.

Overview

Robustel R1510 router is a Dual Ethernet port (LAN + WAN) 3G/4G router with advanced software functions at a very competitive price point.

Package Checklist

Before commencing installation ensure your package has the following components:

  • Device

  • 2-PIN Terminal Block

  • 3-PIN Terminal Block

  • Cellular Antenna

  • Wi-Fi Antenna

  • SIM Card Sticking Patch

  • Mounting Kit (Optional)

  • Power Supply (Optional)

  • Ethernet Cable (Optional)

Note: The accessories could be different on specific order.

Panel Layout (May vary on difference models)

  •  Side View
    Panel Layout

  • Front View
    Panel Layout

  • Back View
    Panel Layout

Interface Descriptions

  1. Power Supply. 2PIN 3.5mm pitch terminal block.
    Interface Descriptions PIN| Power| DI/DO| Description
    ---|---|---|---
    1| V+| —| Power input Positive, 9-36VDC
    2| V-| —| Power input Negative
    3| —| DI| Digital input (Maximum absolute voltage: 30V. Maximum absolute current: 20mA)
    4| —| GND| Ground
    5| —| DO| Digital output (Maximum absolute voltage: 30V. Maximum absolute current: 20mA)
    Interface Descriptions
    DI&DO Internal Diagram
  2. LED Indicator
Name Color Status Description
RUN Green On, solid Router is powered on (System is initializing)
On, blinking Router starts operating
Off Router is powered off
MDM Green On, solid Link connection is working
On, blinking Data is sent and received.
Off Link connection is not working
USR USR-OpenVPN Green On, solid
Off OpenVPN connection is not established
USR-IPsec Green On, solid IPsec connection is established
Off IPsec connection is not established
RSSI Green On, solid Signal Level: Best Signal Level

Wireless module: 21-31dB (signal strength)
On, slow blinking (1s)| Signal Level: Average Signal Level
Wireless module: 11-20dB (signal moderate)
On, fast blinking| Signal Level: Abnormal Signal Level
Wireless module: 21-31dB (signal weak)
Off| No signal
WLAN| Green| On, solid| WLAN is enabled and working properly
Green| Off| WLAN is disabled or not working properly

Note: You can choose the display type of USR LED. For more details, please refer to
RT123_SM_RobustOS Software Manual, Services > Advanced > System >System Settings > User LED Type

  1. Reset Button
    Function| Operation
    ---|---
    Reboot| Press and hold the RST button for 2~ 5 seconds under the operating status.
    Restore to default configuration| Press and hold the RST button for 5~10 seconds, the RUN LED starts blinking quickly, the router will restore to default configuration.
    Restore to factory default settings| Once the operation of restoring default configuration is performed twice within one minute, the router will restore to factory default settings.
    Note: The more details please refer to _RT123_SMRobustOS Software Manual, 2.3 Factory Reset.
  2. Ethernet Ports. There are two Ethernet ports on R1510, including ETH0 (WAN/LAN), and ETH1. Each has two LED indicators. The green one is a link indicator but the yellow one doesn’t mean anything. For details about status, see the table below.
    Ethernet LED Indicator| Status| Description
    ---|---|---
    Link indicator (Green)| On, solid| Connection is established
    On, blinking| Data is being transferred
    Off| Connection is not established

Hardware Installation

  1. SIM Card Installation. Insert the SIM cards into the device, then stick the sticker.
    Hardware Installation

  2. Antenna Installation. Rotate the antenna into the antenna connector accordingly.

  3. Terminal Block Installation. Insert the 2PIN、3PIN terminal blocks into the interfaces connector.
    Hardware Installation

  4. Mounting Kit installation.

    • Wall mountingHardware Installation
    • DIN rail mounting
      Hardware Installation
  5. Connect the Router to a Computer
    Hardware Installation

  6. Power Supply installation. There are two cables associated with the power adapter. Following to the color of the head, connect the cable marked red to the positive pole through a terminal block, and connect the yellow one to the negative in the same way.
    Note: The range of power voltage is 9 to 36V DC.

CONNECTING THE POWER CABLE

COLOR

| POLARITY
---|---

RED

|

+

YELLOW|

Connectting The Power Cable

Login to the Device

  1. Connect the router’s Ethernet port to a PC with a standard Ethernet cable.

  2. Before logging in, manually configure the PC with a static IP address on the same subnet as the gateway address, click and configure “Use the following IP address”.
    Login to the Device

  3. To enter the gateway’s web interface, type http://192.168.0.1 into the URL field of your Internet browser.

  4. Use login information shown in the product label when prompted for authentication.
    Login to the Device

  5. After logging in, the home page of the web interface is displayed, then you can view system information and perform configuration on the device.
    Login to the Device

  6. The automatic APN selection is ON by default, if need to specify your own APN, please go to the menu Interface->Link Manager->Link Setting->WWAN Settings to finish the specific setting.
    Login to the Device

  7. The more configuration details please refer to RT123_SM_RobustOS Software Manual. (END)

Customer Support

Related download link

Find more product documents or tools at: www.robustel.com/en/documentations/

Technical Support
Tel: +86-20-82321505
Email Support: support@robustel.com
Website: www.robustel.com

© 2022 Guangzhou Robustel Co., Ltd.
All rights reserved. Subject to change without notice.

Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals