Proscenic M8 Pro LDS 8.0 Laser Navigation Smart Robot Vacuum Cleaner Instruction Manual

Proscenic M8 Pro LDS 8.0 Laser Navigation Smart Robot Vacuum Cleaner Instruction Manual

www.proscenic.com
support@proscenic.com

Product descriptions

Robot

Host and sensor

2-in-1 Dust bin & water tank

Dust collector unit

Installation Notes

Install dust collector

About your Dust Collector

The dust collector unit is designed to collect dust and charge the robot cleaner. When the cleaning is completed, the robot vacuum automatically returns to the dust collector, which collects all the dirt and dust and recharges the robot vacuum automatically.
A new bag is required to install in the dust collector once it is filled with dust and dirt.

Instructions for use

Instructions for robot

Power on / off
Press and hold the ” ” button to power on, and the robot enters the standby mode. After booting, press and hold the “ ” button to shut down.
Note: When the machine is charging on the dust collector, it will automatically turn on, and it cannot be turned off during charging.

Start / pause
Under the power on state, short press the ” ” button to start the whole house cleaning.
Press any key to pause while cleaning.

Note: It is recommended to let the sweeping robot start cleaning from the dust collector.
When the battery is too low, the cleaning will not start.
Please charge and then start cleaning.
When the power is insufficient during the cleaning process, the robot will automatically return to the dust collector unit for charging.
After the battery is fully charged, it will automatically return to the interrupted location to continue cleaning.

Instructions for dust collector

Start/Stop Button

Short press: Start auto cleaning / pause cleaning
Press and hold for 3s: Start spot cleaning

Pairing of dust collector and robot (Paired in default factory settings)

1. Press and hold the both buttons and on the dust collector simultaneously for 5 seconds: The dust collector enter the pairing mode, the three indicators of the dust collector flash green.
2. Press and hold the button for 5 seconds on the robot: The robot enter pairing mode, the indicators of the robot flash green.
3. Place the robot at the dust collector to charge, and the voice prompts that the pairing is successful.

Charging

Automatic recharging: The robot will automatically return to the dust collector unit to charge after the cleaning is completed or when the battery is low. Manual charging: Press the ” ” button to start recharging. after the machine is powered off, you can manually put the machine back to the dust collector unit to charge.
Note: Please make sure the charging pole piece is in good condition.

Sleep
If there is no operation for more than 20 minutes, the robot will automatically enter the sleeping mode.

Note:
The machine will not enter the sleeping mode when charging.
It will automatically shut down after the power runs out while sleeping.

Home button
Short press: Return to collect dust and charge
Press and hold for 3 seconds: Return to collect dust and then continue to clean from the place where it left off last time

Connect to the mobile client

(2) Scan the QR code below, or search for “ProscenicHome” in the mobile app store the download the app, register and login to the account.http://www.proscenic.cn/app/

(4) Press and hold the “ ” and “ ” keys for 5 seconds to enter network configuration.

(6) go to the mobile phone WLAN list and select and connect the “Proscenia -XXXX” device hotspot.

Remote control

Install the 2-in-1 Dust bin & water tank

Routine maintenance

2-in-1 Dust bin & water tank (recommended weekly)

Universal wheel (recommended to be cleaned monthly)

1. Flip the main unit and pull out the universal wheel upwards.
2. Clean the hair and dust on the wheel, axle and support.
3. Reinstall the universal wheel and press it tight.

Note: Wash with water, dry it and put it back.

Rolling brush (recommended to be cleaned weekly)

1. Turn the main unit, press the left and right buckles, and remove the rolling-brush cover.
2. Remove the rolling brush upwards and clean the entangled hair and rubbish with a cleaning brush.
3. Replace the rolling brush and insert the three legs of the rolling-brush cover into the slot, press down and fix the buckle.

Note: Depending on the usage, it is recommended to replace the roller brush every 6-12 months to ensure the cleaning effect.

Side brush (recommended weekly cleaning)

1. Use a screwdriver to unscrew the side brush screw and remove the side brushed.
2. After cleaning the wrap hair and rubbish on the side brush, replace the side brush.

Note: Depending on the application, it is recommended to replace the side brush for 3-6 months to ensure the cleaning effect.

The main unit and sensor (recommended to be cleaned monthly)
Wipe the sensor on the main unit with a soft, dry cloth, including:

1. 4 cliff sensors at the bottom of the main unit
2. Wall sensor on the right side of the host
3. Infrared auxiliary recharge sensor
4. Charging pole piece on the back of the robot

Dust bag
When the dust bag is full, replace it with a new one according to the mil Dust bag indicator (solid green light).lt is recommended to replace the dust bag every 6-8 weeks.

Cleaning the dust tunnel

1. The dust bag indicator light is solid green, but the dust bag is not full, unplug the dust collector, turn the dust collector over, use a screwdriver to remove the screws as shown in the figure and open the dust duct cover to clean out the foreign objects.
2. Open the air outlet at the rear of the dust collector, clean the sponge filter, and then put it back in.

*Do not disassemble by force, use a screwdriver to remove the screws. Reassemble it according to the original design after each clean.

Cleaning the dust collector infrared lens and I Cleaning the fan filter screen bracket the charging/dust collector clips

Check the infrared lens and charging / dust collection clips of the dust collection unit for dirt. Wipe them with a clean dry cloth to ensure they are clean and free of dirt. It is recommended to wipe them at least once a month.

Check whether there is any lint or debris accumulated on the filter screen bracket of the fan. If there is any, please use the cleaning brush for robot or a dry cloth to remove it. It is recommended to clean it at least once a month.

Basic parameters

Robot

Dust collector unit

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1) This device may not cause harmful interference, and
   (2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

Common problems

Troubleshooting

Robot

Documents / Resources

| Proscenic M8 Pro LDS 8.0 Laser Navigation Smart Robot Vacuum Cleaner [pdf] Instruction Manual
LDSM8PRO, 2ARZX-LDSM8PRO, 2ARZXLDSM8PRO, LDSM8, 2ARZX-LDSM8, 2ARZXLDSM8, M8 Pro LDS 8.0 Laser Navigation Smart Robot Vacuum Cleaner, M8 Pro, LDS 8.0 Laser Navigation Smart Robot Vacuum Cleaner
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>