Proscenic M8 PRO Robot Vacuum and Mop – Refurbished Demonstration Model User Guide

Proscenic M8 PRO Robot Vacuum and Mop – Refurbished

Demonstration

Introduction for connecting to the app via WiFi

Note: The screenshots were taken on an Android device but are similar for Ios devices as well. There are two Proscenic apps in the App Store: “ProscenicHome” and “Proscenic Robotic”. “Proscenic Robotic” only works for older generation robots (Suzuka, 790T and 811GB). So, download the “ProscenicHome” APP to connect.

Download the “ProscenicHome” app and log in

Log in to the “ProscenicHome” app.

1.  Register your “ProscenicHome” account with your email address or phone number. Select “CA”. Please note: If you already have a “ProscenicHome” account, please skip this step.

2. Enter your username and password to log in with your
   “ProscenicHome” account.

3. Add the Proscenic M8 Pro.
   Note: Make sure your device is connected to a 2.4Ghz WiFi network. If your WiFi is 5Ghz, it probably has 2.4Ghz as well. So associate with the latter to connect or go into your router settings.

4. Following the instructions in the screenshots below to turn on your robot and proceed with activating pairing mode.

5. Select the 2.4Ghz WiFi network (e.g. PDCN) and enter your WiFi password. Then press the “Next” button.

6. On the WiFi settings page, switch from the 2.4Ghz Wifi network where you are connected to the robot’s Wifi network, i.e. the Wifi named Proscenic-M8-xxxx. Then go back to “Proscenic”. Now press the “Next” button.
   Note: The two buttons on the robot will change from flashing to solid when the connection is successfully established. You will now be able to control your Proscenic M8 Pro robot in “Proscenic”.

Introduction to Cleaning Mode

Adjustment of suction power and water flow speed.

1. Adjusting the suction power.
   The M8 PRO robot offers 4 levels of suction power:
   Suction 0 (off).

2.  Suction 1.

3.  Suction 2.

4.  Suction 3.
   It can be applied in global cleaning, partition cleaning and area cleaning.
   Note: When cleaning a spot, the robot will default to the maximum suction mode (2700Pa).

5. Water flow speed adjustment.
   The M8 PRO robot offers 4 levels of suction power:

6. Speed 0 (off)

7. Speed 1

8. Speed 2

9. Speed 3
   It can be applied in global cleaning, partition cleaning, area cleaning and one spot cleaning. If you only want to do vacuuming, please set the speed 0 or remove the cloth holder.

Cleaning Mode Settings (Mode List)

Global cleaning
The M8 PRO robot starts cleaning the edge of your home first and then continues with the interior cleaning. When finished, it will return to the charging base (dust collector). In this mode, you can freely adjust the suction mode and water speed flow.

Partition Cleaning

When the robot vacuum cleaner has finished cleaning once in the global cleaning mode, it will automatically divide into partitions on the app. You can also go into the settings and manage the partition management yourself. Selecting an area already divided, you can set a partition, assign it a name, and divide or join other areas of the house. In this mode, you can freely choose the suction and water speed flow.
Note: You can manually subdivide (a division divides into two) the area (or room) that has already been partitioned.

Area cleaning

You can select customize areas (name and adjust cleaning frequency) and perform suction or suction and wash operations. In this mode you can adjust the suction and water speed flow as you like.
Note: Provide settings in a rectangular and polygonal area.

Cleaning a point

Select a specific point on the map and your M8 PRO can go to the identified square area with a diameter of 1.5m on the central point. It will start vacuuming first along the edge of the square area and close in cleaning inwards (default suction setting: 2700pa), vacuum twice and return to the charging base to recharge.

Setting the Restricted Area.
You can set up multiple restricted areas (max. 15) and choose the most suitable shape for your restricted areas (square or polygon). You can also assign names, for example: forbidden area 1 and forbidden area 2. In this way you can formalize your restricted areas.

Y-Shape Washing Mode.
Choose Y washing mode

Cleaning program

Method:

1.  Choose the Cleaning Program in the settings.
2. Add the cleaning list: the cleaning time, the cleaning frequency, the cleaning mode (Global Cleaning, Area Cleaning and Partial Cleaning) and the frequency to empty dust automatically.
3. Tap the “save” symbol. This completes the setting process.

If you prefer, you can also turn on do not disturb mode.
More information in the settings

Introduction of other functions

Cleaning Record.

Device Sharing.
With the function of “add sharing”, you can share the device with your family and friends easily.
Note: The shared account must be registered in the same country as the main account, otherwise you cannot proceed with sharing.

Service life of parts.

About the Robot.

Notification Settings.

Manual control.

Setting the unit of measure

1.  4. Alexa/Google Home Setup
2.  4.1 Alexa configuration
3.  You can connect your M8 PRO robot to Alexa by activating the skill in the Amazon store.
4.  Open the Alexa application and search for the skill “ProscenicHome”.

Hit “Enable to use” as shown in the screenshot.
Now authenticate with your Proscenic account that you have in the application. Select “Europe”.
Now your account is connected to Alexa!
Do the device search and you should now find your M8 Pro in the list.
Google Home configuration
You can connect M8 Pro to your Google Assistant by doing the following:
Tap on “Configure Device”.
Press on “Compatible with Google”
Now login with your Proscenic account and remember to press “Europe”.
Now your device is connected to Google Assistant!

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>