NEEWER CT-16 Camera Flash Trigger Instruction Manual
- June 6, 2024
- NEEWER
Table of Contents
CT-16 Camera Flash Trigger
NEEWER® Camera Flash Trigger
Bm Instruction nual
C….. Thank you for purchasing CT-16 Series Camera Flash Trigger It is a
control discteness formeb trigger
…meh synchronouslThe device is comped of two parts, namely signal tnsmter and
iver. :r.r.a..,…..’.F.11″‘1>’&. b pvent damage to the product r iUy to you or
to othe ad the following safety putions in their entity before using this
equipment.eep these saty instructions where use n ad them for ady reference
A Do not disaemble r modify Failure to obserthis preution could result in
electric shock or product malfunction Should the product break open as the
result of aII or other aident, remove the batteries and e the product to
auorized maintenan nr for inspection.
A Keep
Do not handle with wet hands or immee in orpose
to water or rain. Flure to bserve this precauon culd esult ine or electric
shock.
A Keep out I the reach of children
This device contains small pathat may p se a
chking hazard. Cult a physician immedialya
child swallows any part of this device.
e A Do not expose to high temperature D not leave the devi in a closed vehicle
in the sun or in oer aas subject to enely high mpeture. Flure to obrve this
preution could
… esult in r damae to the casing or inmal parts ·IF.Ti.:C-. ·dy
7
9 8
4
a Ra ivar
5
(1)Sync cJack
(2)Receiving lnditor Lamp
(3)Power Switch
1 (4)ChannelCode Switch (5)UmbIla Input
6
3
(6)Hot Shoe Flash Connection (7)Batcompartment
(8)Hot Shoe Mounting Foot
(9)1/4″ Bracket Mounting H le
Transml
(1OJ Test Button
(11)Channel c de Switch
(12)CameHot Shoe (13)Sync Cord Jack (14)Tnsmitter lnditor Lamp
· Access ries
1. Sync Cable 2. Convert Adapter 3. Insuction Manual
-u1 2
· Battery and Battery Installation
Transmitter: The transmitter is equipped with a 23A 12V lithium-ion battey
which can nonmally be used for over ten thousand times. Receiver. Slide the
battey-chamber cover from the back f the receiver and insert twAAA 1.5V
alkaline batteries (available sepately)
L w Ba·y lndicat r:
LED inditor on receiver will blinkst when the battes
a low. Please change batteries before theyn down in
se offlash failure orflash missing.
Replaclng Baarias:
When replacing batteries on
transmitter or receiver. 1 Tum themeraand disconnect the receiver 2.Remove the batteries with new
ones
A When the device is not in u
1. The transmitter consumes little power and can last or
thee yearwhen it is in spae w10ut any operati n. 2. Theceiver is equipped with
a power n/oswitch. lb
the dain on the batteries when the device is not in use, please slide the
po·er to OFF position. · Channel Settings There are16 channels in this device
Set the tnsmitr and receiver on the same channel before use. Check the ble for
channel seng as below:
Chan1 I2 I3 I4 Is Is I1 Ia Ie 11011111211311411s11s
S1 IO I1 IO I1 IO I1 IO I1 IO I1 IO I1 IO I1 IO I 1
…·l”iB..”·..r.r’··
· lnstructi ns forUse
CT-16 Series Camera Flash Trigger is based on a wiless mote system. The transmitter is equipped with an advand electric circuit It has sleepy function, thus velow power consumption is needed. The iver is used with alternating cunrent, and it achiees quick sponse under the advanced MCU control. It n me the need of syncflash for any diffeent shutterme
· Connection Mount the camerash to Hot Shoe Flash Connectionof the receiver.
Tum on the Power Switch (3)
· Operation
4′
1.Set the transmitter and iver in the same channel position
2. pdown the Testing Button (10), and the Transmitter Indicator Lamp(14)
willflash and simulneously the Receiving Indicator Lamp (2n the iver will also
flash And then the meraflash willflash to wo
3. Attach the tnsmittar onto the me hot shoe mount for no,mal use.
(Conesponding setting is nded in diffent mes.)
4 lf the cameflash ad pts35mm
nccord jack , a sync ble is need Insert one end of the sCble into the Sync
Cord Jack (1)of the iver and the other end into the sync c jack of the flash.
5. When using the syncble and convert adapter together, a studioash can be
triggered. Insert one end of the sync ble into the Sync Cord Jack (1) of the
iver and the other end (with theconvadapter)intoe scco jack of theflash
… … ·t’,1’T..2
M
CT-16
Chanel
16
Transmit f1quency
433MHzwilemo system
Transmittar power Reiver power
Sync s cket
Outd r operation disnee
Ind r opetion dian
12V23A Aithium-ion battery
3V(AAA 6 35mm /<1>3 5mm
S30 m (Open spa
<20m (Open spa
Sync speed
1/250C
Tnsm,tr Dimension
60’42mm
Rever Dimension
90’50’32mm
CTil,r 1. Unable to triggerflash orme shutter. Make su the transmitter and
eceiver ae set to the same channel, and the PC cor the hot shoe mount is
complely connected 2. Signal distuanr shooting interferenChange
derent channel n the device. 3. Operating distance limited rash missing. Check
if
the battey is exhausted Ty to change the battey.
4.Keep away from strong magneticeld. The song
stic r magneticeld produced by devices such as radio tnsmitter leads to
malfunction.
-1,F.I11’ 1. Avoid falling. The device may malfunction after strong shocks or under excess stress.
2.eep dry. The production isn’t water-proof. It will lead
to malfunction if soad in war r ped in high humidwhich use malfunction and
corrosion. 3. Avoid sudden temperature changes, such as the circumstan whenng
the remote control out of a building with higher temperature to ouin winr.
This may lead to condension of moisture. Please put the mote control in
handbag or plastic bag to prevent sudden temperature changes.
82.AOOCT160-00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>