OREIN OS0600112267 Elves HDMI Sync BOX with Lighting Kits User Guide

Elves HDMI Sync BOX with
Lighting Kits
Quick User Guide

Model ID : OS0600112261
OS0600112263
OS0600112267

We appreciate the trust and confidence you have placed in OREIN through the purchase of lighting Kits. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing OREIN.

**IMPORTANT

**

Read carefully before installing the fixture. Retain these instructions for future reference.OREiN fixture must be wired in accordance with the National Electrical Code and all applicable local codes.

SAFETY WARNINGS

Read all product labels and directions. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation WARNING-To prevent

Note:
HDIM Cable(1.4) Can not Support 3840×2160 50FPS/60FPS.

Package Item

Introduction Of Sync Box

Mode Button (short press: change the mode) (long press at least 5s: reset the sync box)| Synchronization mode
---|---
Presets mode
Music mode
Button◁▷| Change Synchronization’ mode
Change Presets’ mode
Change Music’ mode

box and other HDMI signal devices
USB TOP| Strip Light Note: From TV backside view
USB BOTTOM| Strip Light Note: From TV backside view
DC| 12V/2A Power Adapter

HOW TO INSTALL

1. Facing the back of the TV, Paste four brackets: Fixing Bracket-A is glued to the lower right corner and the other 3 are glued to the remaining 3 corners

2. Facing the back of the TV. start from the “start” (right bottom corner), finishing the strips adhesion along from the TOP to the end(left top corner), then we call this light strip as “TOP” strip. Paste the tie holder and fix the extra extended strip light with the strip tie.
   NOTE: Please move the bar through the APP: “①.Device Settings-②.Lightlength Adjust“ to confirm that the light length just covers the TV length. Then you can cut off the additional strips or hang them on the back of the TV.

3.  Facing the back of TV, start from the “start’ (right bottom corner), finish the strips adhesion along from the BOTTOM to the end(left top corner), then we call this light strip a “BOTTOM” strip. Paste the tie holder and fix the extra extended strip light with the Strip tie.
   NOTE: Please move the bar through the APP: “①.Device Settings-②.Lightlength Adjust“ to confirm that the light length just covers the TV length. Then you can cut off the additional strips or hang them on the back of the TV.

4. Finish the fixing bracket, led strips, and connection of the devices

5. Install the brackets clip on the fixing bracket
   5. Connect the devices via input and output port and finally sequentially power on the HDMI sync box.

Connection:

1. Output port-HDMI cable-TV, projector, or monitor screen
2. Input port-HDMI cable-PS4, Switch and other games devices/Computer/Laptops/TV box and other HDMI signal devices
3. DC port-12V power adapter
4. USB port 1(TOP)-TOP led strip
5. USB port 2(BOTTOM)-Bottom led strip

CONNECT THE APP AND SETTING THE Lightlength

1. Get the AiDot APP for Android or iOS
   http://apps.aidot.com

2. Create an account and sign in, enable your location and open your Bluetooth.

3. Press the “+” button to add the Sync Box.

4. Automatic discovery devices which to be added(through BLE protocol), then follow the instructions on App.

5. IMPORTANT: Select “Setting” – “Light length Adjust”, Make sure your Strip lights light on the right length. Then you can be cutting off extra extended strips (You can also keep them then when you change a bigger TV them can help).

Trouble Shootting

Q1: Why I didn’t receive the verification letter for the registration?
A:

1. Please check if you entered a wrong email address during the registration;
2. Check if the mail was stuck in the spam folder;
3. Make sure you have registered on the app instead of the website.

Q2: I failed to get my Sync Box connected to the network, what should
I do?
A: After ensuring the Wi-Fi of your home is 2.4G, we suggest you
reset the Sync Box first.
1. Long press the “Mode” button for 5S to Reset the Sync Box.
2. Readd the Sync Box on the APP If you fail again, don’t worry. It is not necessarily a fault or bug on the product. There are multiple factors that can influence the connection. Please contact our technical team via the contact details shown on the app Or the package. We will check it for you.
Q3.How can I connect the Sync Box to Alexa? A: Step 1: Tap “Me” at the top left corner of the Home page, select settings-Third-Party Services”, Alexa & Hey Google’, Select “Amazon Alexa” When it says “AiDot with Amazon Alexa Step 2: Tap”Sign in with Alexa, follow the on-screen instructions to link your account. When it is successful: it means the connection is done.
Note: If you already have an Alexa APP account but have not signed in Alexa APP. Tap “Sign in with Alexa, t will take you to the sign-in page of Alexa APP Step 3: If Alexa does not successfully add your AiDot devices (which must have been already added in AiDot APP), you can add them by saying “Alexa, discover the device
A: Q4: Why the app states “No Internet Access” when I select the Wi-Fi
of the Sync Box?
B: The notification is from your phone, especially some Android phones instead of our APP. That is because the Wi-Fi of the device does have no access to the Internet, You can tap Connect to proceed. Please do not choose “Cancel”
Q5: How can I share the light control with family members?
A: Step 1: Tap the Home you create on the home page, select “Home Management” enter home share page, Tap the home you want to share.
Step 2: Select “Invite… on the settings page.
Step 3: At the Invite” page, fill in the name and Email of the Invitee you want to add the “Name” here works as a note, not necessarily to be the same aS that used in the APP

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

To maintain compliance with FcC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum of 20cm distance between the radiator and your body: Use only the supplied antenna

SYVIO TECHNOLOGY CO., LIMITED
Room A, 8/F,Kwok Cheung Building, 635-637 Shanghai Street, Mong Kok, Hong Kong
0086-199-2547-1900
www.iorein.com
Support@iorein.com
Follow us on social media
Facebook: @orein.Ied
Youtube: OREiN LED
Made in China

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different
  from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

References

• 888-694-6735" class="nturl" > Technology.co is available at DomainMarket.com. Call 888-694-6735

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>