OREIN CE41a150012021 LED Semi Flush Mount User Manual
- June 8, 2024
- OREIN
Table of Contents
OREIN CE41a150012021 LED Semi Flush Mount
Safety Information
WARNING: PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED, IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE.
Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire or other injuries which could be hazardous or even fatal.
- Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WARNING: Risk of fire or electric shock. Lighting fixture installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
NOTICE: Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warranty
WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in
materials and workmanship for a period of ve (5) years from date of purchase.
This warranty applies only to the original consumer purchaser and only to
products used in normal use and service. If this product is found to be
defective, the manufacturer’s only obligation, and your exclusive remedy, is
the repair or replacement of the product at the manufacturer’s discretion,
provided that the product has not been damaged through misuse, abuse,
accident, modifications, alterations, neglect or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been
improperly installed, set up, or used in any way not in accordance with the
instructions supplied with the product. This warranty shall not apply to a
failure of the product as a result of an accident, misuse, abuse, negligence,
alteration, or faulty installation, or any other failure not relating to
faulty material or workmanship. This warranty shall not apply to the finish on
any portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear.
The manufacturer does not warrant and specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product.
Contact the Customer Service Team at 866-991-2495 or visit www.iorein.com.
Pre-Installation
PLANNING INSTALLATION
WARNING: Shut off power at the circuit breaker or fuse panel before removing the old fixture.
Read all instructions before assembly. Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.
NOTE: Keep your receipt and these instructions for proof of purchase.
TOOLS REQUIRED
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
PACKAGE CONTENTS
| Part | Description | Quantity |
|---|---|---|
| A | Fixture | 1 |
| B | Locking Nut | 2 |
| C | Mounting Deck | 1 |
| D | Mounting Screw | 2 |
| E | Mounting Plate | 1 |
-
Adjust the Color Temperature
- Select your desired color temperature (CCT) from five options:2700K,3000K,3500K,4000K, or 5000K through the toggle switch located on the back of fixture.
-
Mount the Mounting Plate
- Lock the mounting screws (D) to the mounting plate (E).
- Put the mounting plate (E) onto the junction box (not included) and fix with junction box screws (BB).
-
Connect the Wires
- Connect the copper grounding wire of the xture with the one from the junction box. Secure together using a wire nut (AA).
- Connect the black and white wires of the fixture with two wires of the same color from the junction box. Secure together using wire
nuts (AA).
-
Mount the Fixture Body
- Align the keyholes on the back of mounting deck (C) with the mounting screws (D).
- Screw locking nuts (B) onto the mounting screws (D) to secure the fixture body.
-
Turn on the Light
- Restore power and turn on the light.
- Restore power and turn on the light.
Care and Cleaning
- Clean the fixture with a soft, dry cloth.
- Do not use any cleaners with chemicals, solvents, or harsh abrasives.
WARNING: Shut off power at the circuit breaker or fuse panel before cleaning the fixture.
Troubleshooting
Dimmer Compatibility
- FOR USE WITH DIMMER MODELS:
LUTRON: DVCL-153PR-WH, CTCL-153PDH-WH, TGCL-153PH-WH, MACL-153MH-WH, P
-PKG1W-WH-R, MACL153, SCL153, MACL-153MR-WH, MACL-153MH-LA, DVWCL-153PH-WH,
CTCL-153PDH-IV, TGCL-153PR-WH, CTCL-153PR-WH
LEVITON: R62-06674-POw, c22-6672-1LW, R50-IPLO6-10M, 6674, PLO6, IPE04,
R08-TSLO6-1KT, M02-DSLO6-3PW
EATON: AALO6-C1, SALO6P-LA-K, DAL06, DLC03, SALO6, TALO6, ALO6
LEGRAND: HCL453PTCCCV6 120V 450W 60HZ, H703PTUTCCCV6
For a complete list of compatible dimmers, please visit
www.iorein.com
FCC compliance information is listed as below:
- Responsible party: Leedarson America, Inc.
- Responsible party address: 300 Technology Court SE Suite 100, Smyrna, GA 30082
- Telephone number: 678-293-8382
Questions, problems, missing parts? Before returning to the store, call OREIN
Customer Service
8 a.m.-5 p.m., EST, Monday Friday
866-991-2495
www.iorein.com
Retain this manual for future use.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>