Shenzhen Yecon Technology TR08A Face Recognition Intelligent Terminal Instruction Manual
- June 6, 2024
- Shenzhen Yecon Technology
Table of Contents
Shenzhen Yecon Technology TR08A Face Recognition Intelligent Terminal Instruction Manual
Product description
This product is aimed at the needs of large capacity, high performance, wide application, and customization in the face recognition application process. It introduces a face recognition intelligent temperature measurement hardware that can be combined with face recognition algorithms without user cooperation. Realize living body detection, human face dynamic recognition, body temperature induction measurement, warn of abnormal body temperature and remind users to put on masks to provide users with a safe environment for use.
The product is based on Rock chip RK3399, dual-core Cortex-A72 (2.0 GHz) and quad-core Cortex-A53 application processor (1.4 GHz), 200W RGB + IR binocular camera, supports WIFI + Gigabit networking and rich peripheral security interfaces, Meet the needs of user access control management, body temperature detection and identification.
The product is suitable for office areas, hotels, passage gates, office buildings, schools, shopping malls, shops, communities, public services and management, etc. where face recognition and temperature measurement are required.
Features
Specification and performance
Product List
Structure diagram
Wiring description
Note: The electric control lock needs the access control special power supply to supply separately, the condition may increase the UPS uninterrupted power supply.
Electric lock wiring
Access controller connection
Note: The combination of NO and COM is normally open, and the combination of NC and COM is normally closed, respectively to the NO, NC and COM terminals of the access controller. The corresponding wiring mark is printed on the 1 0PIN interface, please refer to the actual product.
Installation instruction
Wrong usage
Wall-mounted installation
On the wall surface about 140cm above the ground, open a groove about 9cm in
length and 5cm in depth, and select a box with a depth of 5cm to install and
fix it.
3 sets of wires need to be embedded in advance at the host equipment (reserved wire length is 10cm):
- 12V power cable RW2 x 1.0 standard and above, one end is at the host device, and the other end is pulled to the original access control dedicated power supply or the 220V power supply 3 hole socket on the top of the sliding door, When installing, connect to the 12V end of the factory supplied 12V1 .8A power adapter. The 220V power cable of the adapter is directly plugged into the 220V power supply 3-hole socket.
- Door opening control line RW2 x 0.5 standard and above, one end is at the host device, and the other end is pulled to the original access control dedicated power supply or the top controller of the sliding door, and connected to their door opening signal interface during installation.
- Cat5e network cable 8 x 0.5 oxygen-free copper standard and above, one end is at the host device, and the other end is pulled to the weak motor room switch, and connected to the Internet during installation. If it is difficult to increase the wired network, you can consider using wireless when the wireless network is stable.
Installation steps
Declaration of toxic and harmful substances
Product warranty card
Thank you for purchasing our products. I guarantee the interests of our
customers. If the products of our company fail due to quality problems, they
can contact the local dealers with the invoice and warranty card.
Warranty notice:
- Within one year from the date of purchase, in case of failure under normal use, the company will provide free warranty, parts replacement and other services according to the fault conditions.
- The warranty card and purchase invoice are the certificates for our company to provide aftersales service to customers. This card is valid after the following forms are filled in in in detail and stamped with the official seal of the dealer.
- Under one of the following circumstances, free warranty service is not implemented, and maintenance is required at a charge;
(1) Beyond the validity of the warranty.
(2) Damage caused by improper use, maintenance or storage not in accordance
with the requirements of the product manual.
(3) Failure and damage caused by dismantling, repairing and refitting products
without permission of our company.
(4) Mechanical failure or damage caused by force majeure.
(5) Wearing parts and random accessories.
This card is issued with the goods, one card for each machine. In order to ensure that you can fully enjoy the right of free warranty service provided by our company, please keep this card properly and do not make up for it if it is lost.
FCC warning statements:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
IC warning statements:
-English Warning Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence exempt
RSS(s). Operation is subject to the following two conditions: (1)This device
may not cause interference. (2)This device must accept any interference,
including interference that may cause undesired operation of the device.
This device complies with ISED RF radiation exposure limits set forth for an
uncontrolled environment. This device must be installed and operated with a
minimum distance of 20 cm between the radiator and user body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>