Peiying PY3258 Car Radio Owner’s Manual
- June 6, 2024
- Peiying
Table of Contents
Peiying PY3258 Car Radio
SAFETY INSTRUCTIONS
Installation precautions
-
This unit is designed to operate on 14,4 V DC power supply. If your vehicle does not have this system, a voltage inverter is required. The device also requires connecting to negative of the car.
-
Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Install the unit where it does not get in the driver‘s way and cannot injure the passenger if there is a sudden stop. DO NOT install the unit or any cable in a location where:
◦ it may obstruct the steering wheel and gearshift lever operations,
◦ it may obstruct the operation of safety devices such as air bags
◦ it may obstruct visibility
◦ there is not enough ventilation provided
◦ there is not enough ventilation provided -
Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, hot air, or a heater, or where it would be subject to dust, dirt or excessive vibration. Do not expose this equipment to rain or moisture nor use near strong magnetic fields. Do not handle this appliance with wet hands.
-
Make sure all the connections are executed in a proper manner. Reversed connection will cause short circuit and damage.
-
If installation angle exceeds 30 from horizontal, the unit might not give its optimum performance.
-
Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
-
If the fuse blows, check the power connection and replace the fuse with one of the same specified rating. If the fuse blows frequently, consult an authorized service point for check-up/ repair.
-
It is recommended to connect speakers with impedance of 4 Ω.
-
To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.
-
Make sure that the ignition is off before connecting the device.
-
Make sure to connect the yellow and red power supply cables after all other cables are already connected.
-
The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
-
At the time of installation, be sure to fix all wires (wires both from this unit and from the car itself) in a way that any wires cannot come into contact with heat sinks on the rear and side of the unit.
-
Installation illustrations show a typical installation. However, you should make adjustments corresponding to your specific car. If you have any questions or require information regarding installation kits, consult your car dealer.
-
If you are not sure how to install this unit correctly, have it installed by a qualified technician. Producer does not claim liability of incorrect mounting/installation nor for inappropriate handling and use disregarding this user’s manual.
-
When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used, parts could become loose or damaged. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
-
When tightening screws or bolts, be careful not to pinch any connection cord.
-
Make sure not to block the ventilation outlets.
-
DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.
-
BEFORE connecting the speaker leads, check the speaker wiring in your car.
-
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. In case of any doubts concerning place of installation, contact your vehicle’s dealer. Before drilling the holes in vehicle’s body, make sure it will not damage any electrical cables or other components. During installation keep in mind, that any loose parts may pose danger in case of an accident – make sure to install every piece properly to ensure safety.
-
Do not remove the housing/disassemble the device. The device has no user-serviceable parts inside. In case of damage, contact an authorized service point for check-up/repair.
Temperature
- If the vehicle has been parked for a long time in hot or cold environment, wait until the temperature in the vehicle becomes normal before operating the unit.
- When installing, to ensure proper heat dispersal when using this unit, make sure to leave some space behind the rear panel and wrap any loose cables so they are not blocking the ventilation outlets.
Safety instructions
- DO NOT operate this device while driving, as this may lead to a traffic accident.
- The driver must not watch the monitor while driving.
- Stop the car before performing any operations! Do not perform any activities that may distract from cautious driving, such as managing playlist.
- Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.
- Clean with soft, slightly damp cloth only.
Hearing safety
- Listen at a moderate volume. Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of sound. So after prolonged listening, what sounds “normal” can actually be loud and harmful to your hearing. To guard against this, set your volume to a safe level before your hearing adapts and leave it there.
- Listen for reasonable periods of time:
◦ Prolonged exposure to sound, even at normally “safe” levels, can also cause hearing lose.
◦ Be sure to use your equipment reasonably and take appropriate breaks.
Notes on external memory
- Use the memory drive only as indicated in its user’s manual
- Do not touch USB port / plug with bare hand; do not touch with metal objects.
- Do not expose memory drive to shocks.
- Do not bend, drop, disassemble, modify the memory drive. Protect from water and humidity.
- Do not store memory drive inside the vehicle where it will be exposed to direct sunlight, high temperatures, high humidity or corrosive substances.
- Make sure the connected USB drive does not obstruct unhindered vehicle driving.
- Memory drive may not function properly in extremely high/low temperature environments.
- Use only authorized memory drives. Please note, the producer does not guarantee compatibility with every external memory.
- Files protected against copying (copyright protection) may not be played.
- In some cases, start of the playback may be delayed, but does not constitute of any malfunction or damage.
- Producer does not claim any liability for any data loss.
- Do not unplug external memory while playback. Change the sound source before disconnecting the memory drive from this device.
INSTALLATION
Mounting
- Insert sleeve into installation holes of dashboard.
- Insert unit into sleeve.
- Install decoration frame on front panel.
Dismounting
- Remove decoration frame.
- Insert the release key into the gap between unit and sleeve.
- Pull out the release key and remove the unit from the dashboard.
WIRE CONNECTION DIAGRAM
FRONT PANEL LAYOUT
- Power Button / Mode button
- Volume/Select knob
- Display Button / Mute /
- LCD Display
- Reset Button
- / Band button
- Tune seek / Forward button
- Tune seek / Backwards button
- Automatically memory storing
- Play/pause / Preset 1 button
- Intro / Preset 2 button
- Repeat / Preset 3 button
- Random / Preset 4 button
- Preset 5 button / 10 songs down
- Preset 6 button / 10 songs up
- AUX input
- USB port
- Microphone
OPERATIONS
General
ON / OFF
Press POWER button to turn on the unit. Press and hold the POWER button to
turn the device off.
SOUND VOLUME ADJUSTMENT
Rotate VOLUME/SELECT knob to adjust volume.
SELECT MENU
Press VOLUME/SELECT knob repeatedly to change between: BAL (balance) > FAD
(fader) > LOUD (loudness) > EQ – Flat/Rock/Pop/Class/User > STEREO > DX > VOL.
Rotate the knob to change settings.
Note:
- when the Equalizer is set, bass and treble adjustment is not available.
- STEREO / MONO: Select mono mode if the FM stations are weak to improve quality of reception.
- LOCAL / DX: Select LOCAL in areas with strong signals to let radio stop at only strong stations during manual turning; select DX in areas with weak signals to listen to all stations.
MUTE
Press MUTE button to mute down the sound. Press it again to unmute and recover
previous volume level.
AREA SETUP
In radio mode, press and hold VOLUME/SELECT knob for few seconds. Rotate the
knob to select between USA/EUR.
MODE SELECTION
Press the mode button to change between different function modes: Radio / USB
/ AUX IN / BT.
Please note, when not connected with any BT device nor any memory storage
(USB) connected, the modes will not be available for selection.
DISPLAY TIME
- Press the DISP button to show time (it will be displayed for 5 seconds)
- Press and hold the DISP button for few seconds, the device will enter time adjustment mode (hour digits will flash). Rotate the knob to set the desired hour. Press the knob to confirm hour, and go to minutes adjustment. Rotate the knob to set the desired minutes. Press the DISP button to confirm and exit time adjustment mode.
RESET
RESET button is placed on the housing (underneath the front panel) and must be
activated with either a ball point pen or a thin metal object (do not use
sharp objects to avoid damaging the unit).
The RESET button is to be activated for the following reasons:
- All function buttons do not operate.
- Error symbol on the display.
Radio
BAND SELECTION
In radio mode, press BAND button to select the desired band. The reception
band will change in the following order: FM1 > FM2 > FM3 > MW1 (AM1) > MW2
(AM2).
STATION SELECTION
In radio mode, default station selection method is automatic. Press TUNE SEEK
/ FORWARD button or TUNE SEEK / BACKWARDS button to start automatic station
tuning function.
Press and hold TUNE SEEK / FORWARD button to change into manual station
selection method, and press repeatedly TUNE SEEK / FORWARD button or TUNE SEEK
/ BACKWARDS button to perform manual tuning mode.
AUTOMATICALLY MEMORY STORING AND PROGRAM SCANNING
Automatic Memory Storing
Press and hold AMS button for few seconds, the radio searches from the current
frequency and the 6 strongest stations are stored into the corresponding
preset number button.
STATION STORING
Use preset button (11~16)
- Preset memory station is loaded after the selected button is pressed.
- Preset memory station is saved when the selected button is pressed and held for few seconds
USB DRIVE INSERTION
Open the rubber plug of the USB port and connect USB drive.
PLAY / PAUSE
Press PLAY/PAUSE button to pause or resume playback.
INT
Press INT button: the device will play the first 10 seconds of each song.
RPT
Press RPT button: the device will enter repeating mode (one, all, folder).
RDM
Press RDM button to turn on/off random playback.
SELECT TRACKS
In USB/SD card mode, press TUNE SEEK/FORWARD button / TUNE SEEK/BACKWARDS
button to go to next/previous song. Press and hold TUNE SEEK/FORWARD button /
TUNE SEEK/ BACKWARDS button to fast forward/fast reverse the song.
BLUETOOTH
Pairing
- Turn on the device.
- Make sure your BT device is nearby this car radio. Turn Bluetooth connectivity on your mobile device and search for external devices.
- Connect with this car radio (CAR AUDIO).
- Input the pairing password “8888” if necessary and confirm. When the pairing connect is successful, the Bluetooth logo on the display will stop blinking.
REMARK: the system supports HSP, HFP, A2DP and AVRCP Bluetooth profiles
Phone call management
After successful connecting this car radio to your mobile device, the receiver
can handle the calls:
- Press button to accept the call.
- Press button to reject the call during an incoming call.
- Press button to end call.
- Press button to transfer the call from car radio to your connected external device. Press button again to transfer the call back to the car radio.
Music playback
In BT mode, user can playback music stored on the connected external device:
- Press TUNE SEEK/FORWARD button / TUNE SEEK/BACKWARDS button to go to next/ previous song.
- Press PLAY/PAUSE button to pause or resume playback.
- Press and hold button to disconnect the Bluetooth. Press and hold button again to reconnect the Bluetooth.
SPECIFICATION
Technical parameters
- Max. power: 4 x 20 W
- S/N ratio: 50 dB
- Channel separation: 50 dB
- Frequency response: 20 Hz – 20 kHz
- Power supply: 14,4 V DC
Main features
-
Readers: USB, AUX
-
Supported formats: MP3
-
Size: 1 DIN
-
Panel: detachable
-
Equalizer: Pop/Rock/Classic/Flat
-
Tone controls:
Bass (at 100 Hz): +/- 7 dB
Treble (at 10 kHz): +/- 7 dB -
Loudness function: yes
-
LCD display: blue backlight
-
Keys backlight: blue
-
Bluetooth: yes
-
Phone call management: yes
Analogue radio tuner
- FM frequency range: 87,5 – 108 MHz
- FM preset memory: 18
- Frequency search: automatic / manual
- Stereo separation: >50 dB
I/O
- USB port: 2.0 (max. capacity: 16 GB)
- AUX socket: Jack 3,5 mm
- RCA output: 4x RCA low impedance line output at 1,2 V
Set includes
- Main unit
- Wiring harness with ISO plug
- Mounting bracket
- Frame
- Mounting accessories
Lechpol Electronics Sp. z o.o. Sp.k. hereby declares that Car Radio PY3258 is consistent with directive 2014/53/UE. Full text of the EU Declaration of Conformity is available at following Internet address: www.lechpol.eu
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems) This marking shown on the product or its literature,
indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environmentor human
health from uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where
they purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k., ul. Garwolińska 1, 08-400 Miętne.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>