Peiying PY3278 Car Radio Owner’s Manual

Car radio PY3278
Owner’s manual 

SAFETY INSTRUCTIONS

Installation precautions

• This unit is designed to operate on a 14,4 V DC power supply. If your vehicle does not have this system, a voltage inverter is required. The device also requires connecting to the negative of the car.

• Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Install the unit where it does not get in the driver‘s way and cannot injure the passenger if there is a sudden stop. DO NOT install the unit or any cable in a location where:
  ◦ it may obstruct the steering wheel and gearshift lever operations,
  ◦ it may obstruct the operation of safety devices such as airbags
  ◦ it may obstruct visibility
  ◦ there is not enough ventilation provided

• there is not enough ventilation provided

• Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, hot air, or a heater, or where it would be subject to dust, dirt or excessive vibration. Do not expose this equipment to rain or moisture nor use near strong magnetic fields. Do not handle this appliance with wet hands.

• Make sure all the connections are executed in a proper manner. The reversed connection will cause a short circuit and damage.

• If the installation angle exceeds 30 from horizontal, the unit might not give its optimum performance.

• Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.

• If the fuse blows, check the power connection and replace the fuse with one of the same specified ratings. If the fuse blows frequently, consult an authorized service point for check-up/ repair.

• It is recommended to connect speakers with an impedance of 4 Ω.

• To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.

• Make sure that the ignition is off before connecting the device.

• Make sure to connect the yellow and red power supply cables after all other cables are already connected.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

• At the time of installation, be sure to fix all wires (wires both from this unit and from the car itself) in a way that any wires cannot come into contact with heat sinks on the rear and side of the unit.

• Installation illustrations show a typical installation. However, you should make adjustments corresponding to your specific car. If you have any questions or require information regarding installation kits, consult your car dealer.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician. The producer does not claim liability of incorrect mounting/installation nor for inappropriate handling and use disregarding this user’s manual.

• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used, parts could become loose or damaged. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

• When tightening screws or bolts, be careful not to pinch any connection cord.

• Make sure not to block the ventilation outlets.

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.

• BEFORE connecting the speaker leads, check the speaker wiring in your car.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. In case of any doubts concerning the place of installation, contact your vehicle’s dealer. Before drilling the holes in the vehicle’s body, make sure it will not damage any electrical cables or other components. During installation keep in mind, that any loose parts may pose danger in case of an accident – make sure to install every piece properly to ensure safety.

• Do not remove the housing/disassemble the device. The device has no user-serviceable parts inside. In case of damage, contact an authorized service point for a check-up/repair.

Temperature

• If the vehicle has been parked for a long time in a hot or cold environment, wait until the temperature in the vehicle becomes normal before operating the unit.

• When installing, to ensure proper heat dispersal when using this unit, make sure to leave some space behind the rear panel and wrap any loose cables so they are not blocking the ventilation outlets.
  Safety instructions

• DO NOT operate this device while driving, as this may lead to a traffic accident.

• The driver must not watch the monitor while driving.

• Stop the car before performing any operations! Do not perform any activities that may distract from cautious driving, such as managing a playlist.

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Clean with soft, slightly damp cloth only.

• When inserting batteries, please note the correct polarity.

• If the remote is not used for an extended period of time, remove the battery to prevent possible damage from battery leakage.
  Hearing safety

• Listen at a moderate volume. Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of sound. So after prolonged listening, what sounds “normal” can actually be loud and harmful to your hearing. To guard against this, set your volume to a safe level before your hearing adapts and leave it there.

• Listen for reasonable periods of time:
  ◦ Prolonged exposure to sound, even at normally “safe” levels, can also cause hearing loss.
  ◦ Be sure to use your equipment reasonably and take appropriate breaks.

Notes on external memory

• Use the memory drive only as indicated in its user’s manual
• Do not touch USB port/plug with the bare hand; do not touch metal objects.
• Do not expose memory drive to shocks.
• Do not bend, drop, disassemble, modify the memory drive. Protect from water and humidity.
• Do not store memory drive inside the vehicle where it will be exposed to direct sunlight, high temperatures, high humidity, or corrosive substances.
• Make sure the connected USB drive does not obstruct unhindered vehicle driving.
• Memory drive may not function properly in extremely high/low-temperature environments.
• Use only authorized memory drives. Please note, the producer does not guarantee compatibility with every external memory.
• Files protected against copying (copyright protection) may not be played.
• In some cases, the start of the playback may be delayed but does not constitute of any malfunction or damage.
• The producer does not claim any liability for any data loss.
• Do not unplug external memory while playback. Change the sound source before disconnecting the memory drive from this device.

INSTALLATION

Mounting

1. Insert the sleeve into installation holes of the dashboard.
2. Insert the unit into the sleeve.
3. Install decoration frame on the front panel.

Dismounting

1. Remove decoration frame.
2. Insert the release key into the gap between unit and sleeve.
3. Pull out the release key and remove the unit from the dashboard.

WIRE CONNECTION DIAGRAM

FRONT PANEL LAYOUT

1. Power Button / Mode button
2. Volume/Select knob
3. Display Button / Mute /
4. LCD Display
5. Reset Button
6. / Band button
7. Tune seek / Forward button
8. Tune seek / Backwards button
9. Automatically memory storing
10.Play/pause / Preset 1 button
11.Intro / Preset 2 button| 12.Repeat / Preset 3 button
13.Random / Preset 4 button
14.Preset 5 button / 10 songs down
15.Preset 6 button / 10 songs up
16. Front panel release button
17. IR sensor
18. AUX input
19. USB port
20. SD/MMC slot
21. Microphone
---|---

OPERATIONS

General
ON / OFF
Press the POWER button to turn on the unit. Press and hold the POWER button to turn the device off.
SOUND VOLUME ADJUSTMENT
Rotate VOLUME/SELECT knob to adjust the volume.
SELECT MENU
Press VOLUME/SELECT knob repeatedly to change between: BAL (balance) > FAD (fader) > LOUD (loudness) > EQ – Flat/Rock/Pop/Class/User > STEREO > DX > VOL. Rotate the knob to change settings.
Note:

• when the Equalizer is set, bass and treble adjustment is not available.
• STEREO / MONO: Selects mono mode if the FM stations are weak to improve the quality of reception.
• LOCAL / DX: Select LOCAL in areas with strong signals to let radio stop at only strong stations during manual turning; select DX in areas with weak signals to listen to all stations.

MUTE
Press the MUTE button to mute down the sound. Press it again to unmute and recover the previous volume level.
AREA SETUP
In radio mode, press and hold the VOLUME/SELECT knob for a few seconds. Rotate the knob to select between USA/EUR.
MODE SELECTION
Press the mode button to change between different function modes: Radio / USB / SD/MMC / AUX-IN / BT. Please note, when not connected with any BT device nor any memory storage (USB/SD card) connected, the modes will not be available for selection.
DISPLAY TIME

• Press the DISP button to show time (it will be displayed for 5 seconds)
• Press and hold the DISP button for a few seconds, the device will enter time adjustment mode (hour digits will flash). Rotate the knob to set the desired hour. Press the knob to confirm the hour, and go to minutes adjustment. Rotate the knob to set the desired minutes. Press the DISP button to confirm and exit time adjustment mode.

RESET
The RESET button is placed on the housing (underneath the front panel) and must be activated with either a ballpoint pen or a thin metal object (do not use sharp objects to avoid damaging the unit). The RESET button is to be activated for the following reasons:

• All function buttons do not operate.
• Error symbol on the display.

Radio
BAND SELECTION
In radio mode, press the BAND button to select the desired band. The reception band will change in the following order: FM1 > FM2 > FM3 > MW1 (AM1) > MW2 (AM2).
STATION SELECTION
In radio mode, the default station selection method is automatic. Press the TUNE SEEK / FORWARD button or the TUNE SEEK / BACKWARDS button to start the automatic station tuning function. Press and hold the TUNE SEEK / FORWARD button to change into manual station selection method, and press repeatedly TUNE SEEK / FORWARD button or TUNE SEEK / BACKWARDS button to perform manual tuning mode.
AUTOMATICALLY MEMORY STORING AND PROGRAM SCANNING
Automatic Memory Storing Press and hold the AMS button for a few seconds, the radio searches from the current frequency, and the 6 strongest stations are stored into the corresponding preset number button.

STATION STORING
Use preset button (11~15)

• The preset memory station is loaded after the selected button is pressed.
• The preset memory station is saved when the selected button is pressed and held for a few seconds.

SD CARD INSERTION

1. Press the front panel release button in the upper left corner of the device to lower the front panel.
2. Insert the SD card into the slot as indicated.
3. To eject the card, push the card lightly until it pops up.

USB DRIVE INSERTION

Open the rubber plug of the USB port and connect the USB drive.

PLAY / PAUSE
Press the PLAY/PAUSE button to pause or resume playback.
INT
Press the INT button: the device will play the first 10 seconds of each song.
RPT
Press the RPT button: the device will enter repeating mode (one, all, folder).
RDM
Press the RDM button to turn on/off random playback.
SELECT TRACKS
In USB/SD card mode, press the TUNE SEEK/FORWARD button / TUNE SEEK/BACKWARDS button to go to the next/previous song. Press and hold the TUNE SEEK/FORWARD button / TUNE SEEK/ BACKWARDS button to fast forward/fast reverse the song. Press Preset 5 button / Preset 6 button to move 10 songs up/down. Please note, when the total quantity of tracks is 10 or less, the function is not available.

BLUETOOTH

Pairing:

1. Turn on the device.
2. Make sure your BT device is nearby this car radio. Turn Bluetooth connectivity on your mobile device and search for external devices.
3. Connect with this car radio (CAR AUDIO).
4. Input the pairing password “8888” if necessary and confirm. When the pairing connect is successful, the Bluetooth logo on the display will stop blinking.
   REMARK: the system supports HSP, HFP, A2DP, and AVRCP Bluetooth profiles.

Phone call management
After successful connecting this car radio to your mobile device, the receiver can handle the calls:

• Press the button to accept the call.
• Press the button to reject the call during an incoming call.
• Press the button to end the call.
• Press the button to transfer the call from the car radio to your connected external device. Press the button again to transfer the call back to the car radio.

Music playback
In BT mode, the user can playback music stored on the connected external device:

• Press the TUNE SEEK/FORWARD button / TUNE SEEK/BACKWARDS button to go to the next/ previous song.
• Press the PLAY/PAUSE button to pause or resume playback.
• Press and hold the button to disconnect the Bluetooth. Press and hold the button again to reconnect the Bluetooth.

REMOTE CONTROL

1. Power Button
2. Pause / Play / Preset 1 butt
3. Intro / Preset 2 button
4. Repeat / Preset 3 button
5. Random / Preset 4 button
6. Preset 5 button / 10 songs
7. Preset 6 button / 10 songs
8. Mute button
9. Volume control buttons
10. Mode button| 11. ST/MO button
12. Loudness button
13. Scan button
14. Display button
15. AMS button
16. LOC / DX button
17. Band / select button
18. Tuning / Selecting tracks / Fast forward / Fast backward
19. Select button
---|---

REPLACING THE REMOTE BATTERY

Replace the CR2025 battery in the remote control with a new one whenever its operational range is shortened or the device does not respond to the remote.
Please note: before the first operation removes the insulation strip from the battery compartment.

1. Retrieve battery compartment

2. Insert the CR2025 battery into the battery compartment. Put the battery with (+) mark upward (when the remote is with buttons facing downward). Pay attention to the correct polarity.

3. Insert the battery compartment back into the remote.

SPECIFICATION

Technical parameters

• Max. power: 4 x 20 W

• S/N ratio: 50 dB

• Channel separation: 50 dB

• Frequency response: 20 Hz – 20 kHz

• Power supply: 14,4 V DC
  Main features

• Readers: USB, SD/MMC, AUX

• Supported formats: MP3

• Size: 1 DIN

• Panel: detachable

• Equalizer: Pop/Rock/Classic/Flat

• Tone controls:
  Bass (at 100 Hz): +/- 7 dB
  Treble (at 10 kHz): +/- 7 dB

• Loudness function: yes

• LCD display: blue backlight

• Keys backlight: blue

• Bluetooth: yes

• Phone call management: yes
  Analog radio tuner

• FM frequency range: 87,5 – 108 MHz

• AM frequency range: 522 – 1620 kHz

• FM preset memory: 18

• AM preset memory: 12

• Frequency search: automatic/manual

• Stereo separation: >50 dB
  I/O

• USB port: 2.0 (max. capacity: 16 GB)

• Memory card reader: standard SD (max. capacity: 16 GB, class 10)

• AUX socket: Jack 3,5 mm

• RCA output: 4x RCA low impedance line output at 1,2 V
  Set includes

• Main unit

• Panel

• Wiring harness with ISO plug

• Remote control

• Mounting bracket

• Frame

• Mounting accessories

Lechpol Electronics Sp. z o.o. Sp.k. hereby declares that Car Radio PY3278 is consistent with directive 2014/53/UE. Full text of the EU Declaration of Conformity is available at the following Internet address: www.lechpol.eu.

English
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature indicates that it should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of waste and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their suppliers and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k., ul. Garwolińska 1, 08-400 Miętne.

www.peiying.pl

References

• Rebel Electro - Co weekend SuperOkazje

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>