audio-technica AT4033a Cardioid Condenser Side Address Microphone User Manual

: June 15, 2024
: Audio-Technica

Table of Contents

audio-technica AT4033a Cardioid Condenser Side Address Microphone
Product Information
Product Usage Instructions
Features
Safety precaution
Connection procedure
Switch settings
Specifications
Dimensions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

audio-technica AT4033a Cardioid Condenser Side Address Microphone

Product Information

Specifications

Element: Fixed-charge back plate, permanently polarized condenser
Polar pattern: Cardioid
Frequency response: 30-20,000 Hz
Low cut: 80 Hz, 12 dB/octave
Pad: -10 dB
Open circuit sensitivity: -32 dB (25.1 mV) (0dB = 1 V/Pa, 1 kHz)
Impedance: 100 ohms
Maximum input sound level: 145 dB SPL (1 kHz at 1% THD), 155 dB SPL (When pad is on.)
Noise: 17 dB SPL (A-weighted)
Dynamic range: 128 dB (1 kHz at Max SPL)
Signal-to-noise ratio: 77 dB (1 kHz at 1 Pa, A-weighted)
Phantom power requirements: 48 V DC, 3.2 mA
Switches: Low cut (on/off), Pad (on/off)
Weight: 380 g (13.4 oz)
Dimensions: 170.0 mm (6.69) long, 53.4 mm (2.10) maximum body diameter
Output connector: Integral 3-pin XLR-M type
Audio-Technica case style: R1
Included accessories: AT8449a shock mount, stand adapter (3/8-5/8), microphone dust cover, carry case

Product Usage Instructions

Safety Precautions
Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product.

Cautions for the Product
Avoid using the product in hot, humid, or dusty places.

Connection Procedure

Connect the output terminals of the microphone to a device that has a microphone input (balanced input) compatible with a phantom power supply.
The output connector is an XLRM-type with polarity as shown in the figure below:

$audio-technica-AT4033a-Cardioid-Condenser-Side-Address-Microphone-FIG- $2$$

PIN1 (ground)
PIN2 (hot)
PIN3 (cold)

Switch Settings

To reduce the pickup of low-frequency ambient noise (such as traffic, air- handling systems, etc.), room reverberation, and mechanically coupled vibrations, turn ON the low-cut filter switch located on the side. If audio input exceeds the maximum input sound level, set the pad switch to -10 dB.

Low cut: on/off
Pad: on/off

FAQ

Q: What is the weight of the AT4033a microphone?
A: The weight of the AT4033a microphone is 380 g (13.4 oz).
Q: What are the included accessories with the AT4033a microphone?
A: The included accessories with the AT4033a microphone are the AT8449a shock mount, stand adapter (3/8-5/8), microphone dust cover, and carry case.

Thank you for purchasing this product. Before using the product, read through the user manual to ensure that you will use the product correctly. Please keep this manual for future reference.

Features

Specially engineered to meet the most critical acoustic requirements of professional recording, broadcast and sound reinforcement
Transformerless circuitry virtually eliminates low-frequency distortion and provides superior correlation of the high-speed transients
The 2-micron thick, vapor-deposited gold diaphragm undergoes a fivestep aging process so that the optimum characteristics achieved remain constant over years of use
Floating-construction capsule assembly provides isolation from noise and vibration
Precision-machined, nickel-plated brass, acoustic element baffle provides enhanced element stability and optimal sensitivity
Open acoustical environment of the symmetrical housing assembly minimizes unwanted internal reflections
Custom shock mount provides superior isolation
Integral 80 Hz low-cut filter switch and 10 dB pad switch
State-of-the-art design and manufacturing techniques ensure compliance with A-T’s stringent consistency and reliability standards

Safety precaution

Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product.

Cautions for the product

Do not subject the product to strong impact to avoid malfunction.
Do not disassemble, modify or attempt to repair the product.
Do not handle the product with wet hands to avoid electric shock or injury.
Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty place.

Notes on use

A raised Audio-Technica emblem is on the front of the microphone. Position this side of the microphone toward the sound source.
In use, secure the cable to the microphone stand or boom, leaving a slack loop at the microphone. This will ensure the most effective shock isolation and reduce the possibility of accidentally pulling the microphone out of its mount.

Connection procedure

Connect the output terminals of the microphone to a device that has a microphone input (balanced input) compatible with a phantom power supply. The output connector is an XLRM-type with polarity as shown in the figure below.

Switch settings

To reduce the pickup of lowfrequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically coupled vibrations, turn ON ( ) the low-cut filter switch located on the side.
If audio input exceeds the maximum input sound level, set the pad switch to -10 dB.

Specifications

Element Fixed-charge back plate, permanently polarized condenser
Polar pattern Cardioid
Frequency response 30-20,000 Hz
Low cut 80 Hz, 12 dB/octave
Pad -10 dB
Open circuit sensitivity -32 dB (25.1 mV) (0dB = 1 V/Pa, 1 kHz)
Impedance 100 ohms
Maximum input sound level 145 dB SPL (1 kHz at 1% THD) 155 dB SPL (When pad is on.)
Noise 17 dB SPL (A-weighted)
Dynamic range 128 dB (1 kHz at Max SPL)
Signal-to-noise ratio 77 dB (1 kHz at 1 Pa, A-weighted)
Phantom power requirements 48 V DC, 3.2 mA
Switches Low cut: on/off, Pad: on/off
Weight 380 g (13.4 oz)
Dimensions 170.0 mm (6.69″) long, 53.4 mm (2.10″) maximum body diameter
Output connector Integral 3-pin XLR-M type
Audio-Technica case style R1
Included accessories AT8449a shock mount, stand adapter (3/8”-5/8”),